Rice husk silica as a sustainable filler in the tire industry

In this paper, we studied commercially available precipitated rice husk silica (RHS) with conventional precipitated silica, which has nearly the same surface area, and replaced part of the carbon black with RHS and conventional silica in a basic tread formulation. All formulations were mixed with the same amount of filler during the study. Silica was used at 15, 30 and 50 phr loading, and part of the carbon black was replaced by silica. Compound curing characteristics, physical properties, rebound resilience, heat generation, abrasion loss, dynamic properties and morphology were analyzed. The results indicated that RHS demonstrated compound properties comparable to those of conventional silica. As part of the carbon black was replaced with conventional silica, a slower cure rate, higher rebound resilience, lower heat generation, lower abrasion loss, and lower tan delta were observed with no significant change in physical properties, but some changes in physical properties were observed using one way ANOVA analysis. We found the same trend when replacing part of the carbon black with RHS, such as a slower cure rate, higher rebound resilience, lower heat generation, lower abrasion loss, and lower tan delta with no significant change in physical properties, but some changes in physical properties were observed using one way ANOVA. This sustainable material could be used to replace conventional silica in tire compounding, as well as to replace a portion of carbon black with RHS for improved heat build-up, rolling resistance, and abrasion loss.     

Quantum states in fabricating poly-Si films

The quantum states are presented in these processions of fabricating poly-Si films. Amorphous silicon films prepared by PECVD has been crystallized by conventional furnace annealing (FA) and rapid thermal annealing (RTA), respectively. It is found that the thin films grain size present quantum states with the increasing of the gas flow ratios of SiH₄, H₂ mixture, substrate temperatures, frequency power, annealing temperature and time.     

Controlled synthesis of amphiphilic biodegradable polylactide‐grafted dextran copolymers

The whole controlled synthesis of novel amphiphilic polylactide (PLA)‐grafted dextran copolymers was achieved. The control of the architecture of such biodegradable and potentially biocompatible copolymers has required a three‐step synthesis based on the “grafting from” concept. The first step consisted of the partial silylation of the dextran hydroxyl groups. This protection step was followed by the ring‐opening polymerization of D ,L ‐lactide initiated from the remaining OH functions of the partially silylated polysaccharide. The third step involved the silylether group deprotection under very mild conditions. Based on previous studies, in which the control of the first step was achieved, this study is focused on the last two steps. Experimental conditions were investigated to ensure a controlled polymerization of D ,L ‐lactide, in terms of grafting efficiency, graft length, and transesterification limitation. After polymerization, the final step was studied in order to avoid degradation of both polysaccharide backbone and polyester grafts. The chemical stability of dextran backbone was checked throughout each step of the synthesis. PLA‐grafted dextrans and PLA‐grafted (silylated dextrans) were proved to adopt a core‐shell conformation in various solvents. Furthermore, preliminary experiments on the potential use of these amphiphilic grafted copolymers as liquid/liquid interface stabilizers were performed. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2577–2588, 2004     

Desorption behavior of a surfactant in a linear low‐density polyethylene blend at elevated temperatures

The desorption behavior of a surfactant in a linear low‐density polyethylene (LLDPE) blend at elevated temperatures of 50, 70, and 80 °C was studied with Fourier transform infrared spectroscopy. The composition of the LLDPE blend was 70:30 LLDPE/low‐density polyethylene. Three different specimens (II, III, and IV) were prepared with various compositions of a small molecular penetrant, sorbitan palmitate (SPAN‐40), and a migration controller, poly(ethylene acrylic acid) (EAA), in the LLDPE blend. The calculated diffusion coefficient (D) of SPAN‐40 in specimens II, III, and IV, between 50 and 80 °C, varied from 1.74 × 10^?11 to 6.79 × 10^?11 cm²/s, from 1.10 × 10^?11 to 5.75 × 10^?11 cm²/s, and from 0.58 × 10^?11 to 4.75 × 10^?11 cm²/s, respectively. In addition, the calculated activation energies (E_D) of specimens II, III, and IV, from the plotting of ln D versus 1/T between 50 and 80 °C, were 42.9, 52.7, and 65.6 kJ/mol, respectively. These values were different from those obtained between 25 and 50 °C and were believed to have been influenced by the interference of Tinuvin (a UV stabilizer) at elevated temperatures higher than 50 °C. Although the desorption rate of SPAN‐40 increased with the temperature and decreased with the EAA content, the observed spectral behavior did not depend on the temperature and time. For all specimens stored over 50 °C, the peak at 1739 cm^?1 decreased in a few days and subsequently increased with a peak shift toward 1730 cm^?1. This arose from the carbonyl stretching vibration of Tinuvin, possibly because of oxidation or degradation at elevated temperatures. In addition, the incorporation of EAA into the LLDPE blend suppressed the desorption rate of SPAN‐40 and retarded the appearance of the 1730 cm^?1 peak. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1114–1126, 2004     

Solubility parameter determination of cationic surfactants by inverse GC

Summary The solubility parameters of cationic surfactants were obtained using the inverse gas chromatographic technique. The surfactants didodecyl dimethyl ammonium bromide, dioctadecyl dimethyl ammonium bromide and dodecyl pyridinium chloride were used as stationary phase and retention data of different probe solutes were measured at different temperatures. The results were analysed by the combination of Flory-Huggins and Hildebrand theories, and the solubility parameters of the surfactants were obtained in a range of temperatures between 80–120°C.     

Effect of maltodextrins on the surface activity of small-molecule surfactants

We report on the effect of commercially important polysaccharides (maltodextrins with variable dextrose equivalent (Paselli SA-2, MD-6 and MD-10) on the surface activity at the air–water interface of small-molecule surfactants (sms), possessing different hydrophobic–lipophilic balance ((SSL (Na⁺), the main component is a sodium salt of stearol–lactoyl lactic acid, and PGE (080), polyglycerol ester of C18 fatty acid), and widely used in food products. A marked change of the surface activity of sms was found in the presence of maltodextrins by tensiometry. The combined data of laser multiangle light scattering and mixing calorimetry have suggested that this result is governed by specific complex formation between maltodextrins and sms in aqueous medium. Measurements have been made of the molar mass, the second virial coefficient and the enthalpy of intermolecular interactions in aqueous solutions. The implication of a degree of polymerization of maltodextrins in this phenomenon was shown. The interrelation between the molecular parameters of the formed complexes and their surface activity at the air–water interface has been revealed and discussed.     

A Study on Stripping Voltammetric Determination of Osmium(IV) at a Carbon Paste Electrode Modified In Situ with Cationic Surfactants

This article deals with the development of a method for the determination of osmium at a carbon paste electrode (CPE) modified with cationic surfactants of the quaternary ammonium salt type; namely, cetyltrimethylammonium bromide (CTAB) and 1‐(ethoxycarbonyl)‐pentadecyltrimethyl‐ammonium bromide (Septonex); both being added in situ and serving for preconcentration of osmium via its hexachloroosmate(IV) anion. The proper electrochemical detection was performed by cathodic scanning in the differential pulse voltammetric mode. Optimization studies concerning important experimental parameters also included a specially performed potentiometric titration, helping to define the actual stoichiometry for the ion‐pairing process, the main principle and driving force of the accumulation step. In a chloride/acetate buffer based supporting medium and with Septonex as the modifier of choice, the reduction signal for osmium was found to be proportional to the Os(IV) concentration in a range from 5×10^?9 to 5×10^?7 mol L^?1 with a limit of detection close to 5×10^?9 mol L^?1 (with preconcentration for 60 s). The method capable to determine Os(IV) in the presence of both Pt(IV) and Ir(III) was tested on model solutions as well as with real sample of industrial waste water (spiked with the analyte); both yielding the recovery rates within 88–99%.     

Photocrosslinked poly(vinylbenzophenone)‐core micelles via mild Friedel–Crafts benzoylation of polystyrene amphiphiles

Photocrosslinkable poly(vinylbenzophenone)‐containing polymers were synthesized via a one‐step, Friedel–Crafts benzoylation of polystyrene‐containing starting materials [including polystyrene, polystyrene‐block‐poly(tert‐butyl acrylate), polystyrene‐block‐poly(ethylene oxide), polystyrene‐block‐poly(methyl methacrylate), and polystyrene‐block‐poly(n‐butyl acrylate)] with benzoyl trifluoromethanesulfonate as a benzoylation reagent. The use of this mild reagent (which required no added Lewis acid) permitted polymers with well‐defined compositions and narrow molecular weight distributions to be synthesized. Micelles formed from one of these benzoylated polymers, [polystyrene_0.25‐co‐poly(vinylbenzophenone)_0.75]₁₁₅‐block‐poly(acrylic acid)₁₄, were then fixed by the irradiation of the micelle cores with UV light. As the irradiation time was increased, the pendent benzophenone groups crosslinked with other chains in the glassy micelle cores. Dynamic light scattering, spectrofluorimetry, and Fourier transform infrared spectroscopy were all used to verify the progress of the crosslinking reaction. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2604–2614, 2006     

Calorimetric approach to tetronic/water interactions

Tetronic^®comprises X-shaped copolymers formed by four poly(propylene oxide) (PPO) andpoly(ethylene oxide) (PEO) block chains bonded to an ethylene diamine centralgroup. Micellization behaviour of three representative Tetronics (T304, T904and T1307) was characterized to gain an insight into the interactions betweenthe copolymer unimers and the state of water in their solutions. The enthalpyof demicellization, recorded at 37°C in an isoperibol microcalorimeter,indicated that the process was in all cases exothermic and the enthalpy rankedin the order T1307≥T904>>T304. Micellization is entropy-driven owing tohydrophobic interactions between the PPO chains.DSC analysisshowed that the crystallization and melting peaks of the free water remainingin T304 and T904 solutions were progressively shifted toward lower temperaturesas the surfactant proportion increased, owing to a colligative effect. Boundwater corresponded to 3 water molecules per EO repeating unit. In the caseof T1307, which has longer PEO chains, a splitting of the melting peak wasobserved, one peak appearing around 0°C due to free water and anotherat –15°C due to interfacial water. As T1307 proportion raised, theenthalpy of the former decreased, whilst the enthalpy of the latter increased.In 40% T1307 solutions, interfacial water overcame the proportion of freewater; there being 1 interfacial and 3 bound water molecules per EO repeatingunit. Gaussian deconvolution of FTIR spectra also enabled to characterizethe evolution of free water as a function of Tetronic proportion. The dependenceof micellization and water interaction behaviour on Tetronics structure shouldbe taken into account to use these copolymers as drug solubilizers and micellarcarriers.