NMR investigation of concentrated alumina and silica slurries

The longitudinal relaxation times (T₁) of water in concentrated silica and alumina slurries were measured as a function of solids content. It was shown that the results could be fit very well with a two-phase fast-exchange model between free and surface-bound water. As expected, values of T₁ for bound water were in the order of 20–2000 times lower than that for free water, indicating a higher effective viscosity of the surface-bound water. The strength of the interaction depended on the particular surface, and all of the aluminas examined interacted more strongly with water than the two silicas studied, which themselves differed considerably. The chemical mechanical polishing (CMP) removal rate of tantalum by silica slurries was shown to be directly correlated with the interaction parameters, derived from the NMR relation times rather than with total surface hydroxyl group concentration.     

On practical metrology and chemical analysis: etalons and traceability systems

 National measurement systems are infrastructures to ensure, for each nation, a consistent and internationally recognised basis for measurement. Such complex systems have historical, technical, legal, organisational and institutional aspects to connect scientific metrology with practical measurements. Underlying any valid measurement is a chain of comparisons linking the measurement to an accepted standard. The ways the links are forged and the etalons (measurement standards) to which they connect are defining characteristics of all measurement systems. This is often referred to as traceability which aims at basing measurements in common measurement units – a key issue for the integration of quantitative chemical analysis with the evolving physical and engineering measurement systems. Adequate traceability and metrological control make possible new technical capabilities and new levels of quality assurance and confidence by users in the accuracy and integrity of quantitative analytical results. Traceability for chemical measurements is difficult to achieve and harder to demonstrate. The supply of appropriate etalons is critical to the development of metrology systems for chemical analysis. An approach is suggested that involves the development of networks of specialised reference laboratories able to make matrix-independent reference measurements on submitted samples, which may then be used as reference materials by an originating laboratory using its practical measurement procedures. Received: 31 July 1995 Accepted: 19 August 1995     

Shape transition from InAs quantum dash to quantum dot on InP(3 1 1)A

We report on the shape transition from InAs quantum dashes to quantum dots (QDs) on lattice-matched GaInAsP on InP(3 1 1)A substrates. InAs quantum dashes develop during chemical-beam epitaxy of 3.2 monolayers InAs, which transform into round InAs QDs by introducing a growth interruption without arsenic flux after InAs deposition. The shape transition is solely attributed to surface properties, i.e., increase of the surface energy and symmetry under arsenic deficient conditions. The round QD shape is maintained during subsequent GaInAsP overgrowth because the reversed shape transition from dot to dash is kinetically hindered by the decreased ad-atom diffusion under arsenic flux.     

基团共轭效应研究Ⅱ：^13C核磁共振的化学位移与取代基的共轭效应强度

引言在定量和定性研究有机化合物的结构与性质的关系中,最广泛使用的是Hammett等所提出的σ_m、σ_p等取代基常数以及基团的诱导(场)效应和共轭效应常数。在建立基团的共轭效应常数方面,人们做了大量的工作,但多数工作是基于对基团的Hammett常数σ的人为分解上,建立的模型和分解方式(系数因子)不同,则得到不同的结果。另一方面纯理论计算工作大多引入较多参数,使计算复杂和使用不便。作者曾在建立表征诱导效应大小的     

Molecular potential-energy surfaces for chemical reaction dynamics

This paper reviews the construction of molecular potential-energy surfaces by an interpolation method which has been developed over the last several years. The method uses ab initio quantum chemistry calculations of the molecular electronic energy in an automated procedure to construct global potential- energy surfaces which can be used to simulate chemical reactions with either classical or quantum dynamics. The methodology is explained and several applications are presented to illustrate the approach. Received: 22 February 2002 / Accepted: 2 May 2002 / Published online: 6 November 2002 Correspondence to: M. A. Collins e-mail: collins@rsc.anu.edu.au Acknowledgements. The methods described in this overview are the result of collaborations with former members of my group, in particular with Josef Ischtwan, Meredith Jordon, Keiran Thompson and Ryan Bettens. I am also indebted for inspiration gained from many discussions with my colleagues Leo Radom and Donghui Zhang (National University of Singapore). This work has been supported by the Supercomputer Facility of the Australian National University and the Australian Partnership for Advanced Computing.     

Chemical separation and inductively coupled plasma–atomic emission spectrometric determination of seventeen trace metals in thorium oxide matrix using a novel extractant – Cyanex-923

Comprehensive studies have been carried out on the extraction behaviour of thorium matrix vis-a-vis 17 trace metallic elements using a novel extractant viz. Cyanex-923. The near total extraction of thorium and quantitative separation of these metals has been established using inductively coupled argon plasma–atomic emission spectrometry (ICP–AES). The recovery of few representative elements has been confirmed by radio-active tracer studies. The studies carried out here have enabled determination of μg/l amounts of all analyte elements with a precision of better than 1% RSD with prior chemical separation from as low as 1 g thorium sample in just five chemical extractions.     

WATER-BLOWN POLYURETHANE RIGID FOAMS MODIFIED BY CHEMICAL PLASTICATION

1. INTRODUCTIONThese years, HCFC-141b may be the most used blowing agent for its useful properties. But, because of its high global warming effect leading to the destruction of the ozone layer, production of HCFC141b has been forbidden. However, there are…     

Rearrangement during cyclisation of some 3-(2-pyrrolyl) propionic acids and related compounds

Cyclisation of the title compounds leads to mixtures of the expected 4H-cyclopental[b]pyrrol-4-ones (1), the corresponding 6-ones (3) by a single rearrangement, and the cyclopenta[c]pyrrol-4-ones (4) by a double rearrangement, the proportions depending upon the substituents.The ¹H NMR spectra of 2-methyl-4H-cyctopenta[b]thiophen-6-one (3f) shows 6J long range $\text{CH}{}_3\text{CH}{}_2$ coupling, but this is absent in the corresponding pyrroles (3c,d). The ¹³C spectra of 1 and 3 cannot be interpreted on the basis of substituent chemical shifts in pyrroles and thiophens, and are clearly -CH = CH-X (X = NMe, NPh, S) bridged derivatives of cyclopent-2-enone.     

Chemical and thermal analysis of the biopolymers in thyme (Thymus vulgaris)

Thyme (Thymus vulgaris) has been known, long time ago, for its aromatic properties. It contains essential oils and polymers such as cellulose (mixture of hemicellulose and cellulose) and lignin. The thyme, studied in this work, was gathered from the same place, in the period from November 1999 to October 2000. The chemical analysis (water, total ash, essential oils, extractive substances, cellulose, holocellulose and lignin) can be used roughly in the characterisation of the four periods that correspond to the four seasons of the year. The cellulose level was found to be more than lignin level in the wet periods (growth of the plant). The opposite was found in the dry periods. The total ash and essential oil levels were found to be high during the period of high pluviometry. The thermal decomposition of cellulose and holocellulose was found to fit well with the first-order kinetics. The activation energy, under air flow, was 185 and 196 kJ mol⁻¹ for cellulose and holocellulose, respectively. The maximum decomposition rate and thermal analysis heating rate of lignin were found to have a direct linear relationship.     

Potentiometric studies of dithiooxamide with a sulphide-selective membrane electrode

The sulphide-selective electrode is applicable to the determination of dithiooxamide by titration with silver nitrate. The effect of the alkali content of the solutions on the reaction has been studied. The reaction products are silver sulphide, oxalic acid, and nitric acid. If the alkali concentration of the solution is lower than that equivalent to the acid formed during the titration, the amount of sulphide produced by hydrolysis decreases and the equilibrium potential is established more slowly.The determination is rapid and accurate in the presence of 1 M sodium hydroxide.