Characterization of ceramic PVD thin films on AZ31 magnesium alloys

Ceramic thin films have been widely used to protect the metal substrate as coatings in the past years. In order to improve the poor corrosion resistance of AZ31 magnesium alloy, the study in this paper used the electron beam evaporation method to prepare ceramic PVD films on its surface with TiO₂ and Al₂O₃ as donors, respectively. Atomic force microscopy (AFM), scanning electron microscope (SEM), energy dispersive X-ray spectrometer (EDS), Auger electron spectroscopy (AES) and X-ray diffraction (XRD) were used to investigate the surface morphology, composition and microstructure of the thin films. Both films deposited on AZ31 took on compact top surface morphologies and grew as amorphous structures on substrate. AES test not only showed that films compositions deviated the standard stoichiometric ratios, but also found that element Mg diffused into films and existed as magnesium oxide in the TiO_x film as well as the AlO_x film. In the electrochemical corrosion test, the AlO_x coating on AZ31 exhibited the largest electrochemical impedance in a 3.5% NaCl solution. But it did not show better corrosion resistance than others for the poorer adhesion. Even if its thickness was small, the TiO_x coating on AZ31 exhibited the best corrosion resistance in this study. According to the observation and analysis, the damage of these films on AZ31 in aggressive solutions was mainly due to the existence of pores, microcracks, vacancies and poor adhesion between coating and substrate.     

Energy storage in Ce-doped LiCaAlF6 and LiSrAlF6 crystals

Absorption, emission and thermoluminescence (TL) of as-grown and X-irradiated pure and Ce-doped LiCaAlF₆ (LiCAF) and LiSrAlF₆ (LiSAF) crystals have been analyzed. It is shown that the energy storage is defined by the dissimilarity of basic matrix properties, intrinsic defect structure, preferred Ce³⁺ ion disposition and charge compensation defect type. This is the reason of higher colorability and TL efficiency of as-grown Ce:LiSAF compared to Ce:LiCAF. Pre-filling of ultra-deep traps leads to enormous increases in the TL response. Due to these properties Ce:LiSAF and Ce:LiCAF are promising thermoluminescent dosimetric materials.     

Sonochemistry and its dosimetry

The effects of ultrasound originate primarily in acoustic cavitation. The cavitation bubbles collapse violently enough to lead to interesting chemical effects, known as sonochemistry. There is a great need to relate the efficiency of sonochemical reaction to the energy of ultrasonic irradiation used to produce them. In this paper, three OH radical dosimeters, Fricke dosimeter, terephthalate dosimeter, and iodide dosimeter, are compared from the analytical point of view. The dosimeters based on photometry, i.e., Fricke and iodide, produced reliable and reproducible results, but the sensitivity is not enough for special applications, such as chemical monitoring of single bubble cavitation. The dosimeter based on fluorometry, terephthalate dosimeter, offered high sensitivity, 1.2×10¹¹ molecules ml⁻¹. The effects of some experimental parameters in sonochemistry, i.e., solution temperature and the dissolved gas species, were evaluated with the dosimeters.     

Chromium and yttrium-doped magnesium aluminum oxides prepared from layered double hydroxides

Layered double hydroxides with the hydrotalcite-like structures, containing Mg²⁺ and Al³⁺, doped with Cr³⁺ and Y³⁺, have been prepared by precipitation at constant pH. The weight percentages of Cr³⁺ and Y³⁺ were 1, 2, or 3%, and 0.5 or 1%, respectively. Single phases were obtained in all cases, whose crystallinity decreased as the content in Cr and Y was increased. The solids have been characterised by element chemical analysis, powder X-ray diffraction, thermal analyses (differential, thermogravimetric and programmed reduction), FT-IR and UV–vis spectroscopies; the specific surface areas have been determined from nitrogen adsorption isotherms at −196 °C. Upon calcination at 1200 °C for 5 h in air all solids display a mixed structure (spinel and rock salt for MgO); these solids have also been characterised by these techniques and their chromatic coordinates (CIE – L^*a^*b^*) have been determined. Their pink colour makes these solids suitable for being used as ceramic pigments.     

Study of Sb‐doped SnO2 Gray Ceramic Pigment with Cassiterite Structure

In this study, Sb_xSn_1?xO₂ (0 ≤ x ≤ 0.5) compositions were synthesized by the ceramic method from Sb₂O₃‐SnO₂ and Sb₂O₅‐SnO₂ mixtures and characterized by Differential thermal analysis (DTA) and thermogravimetric analysis (TG), X‐ray diffraction, UV‐V‐NIR spectroscopy and CIE L*a*b* (Commission Internationale de l'Eclairage L*a*b*) parameters measurements. Solid solutions with cassiterite structure were obtained at 1300 °C. These solid solutions are stable into glazes. From Sb₂O₃, light gray coloured materials were obtained. From Sb₂O₅, bluish gray coloured materials were obtained at 1300 °C/6h when x ≥ 0.3. Sb_xSn_1?xO₂ with 0.3 ≤ x < 0.5, T = 1300 °C and Sb₂O₅ might be established as compositional range, fired temperature and antimony precursor to obtain gray ceramic pigments in this system.     

Simultaneous deposition of Ni nanoparticles and wires on a tubular halloysite template: A novel metallized ceramic microstructure

Tubular halloysite can be used as a template to fabricate a novel metallized ceramic microstructure through electroless plating. Reduction of Pd ions by methanol is conducted to initiate Ni plating. There is a simultaneous deposition of Ni nanoparticles on the outer surface and discontinuous wires in the lumen site of the halloysite template obtained. The different deposition could be caused by the different composition distribution of ferric oxide impurity in the wall due to the isomorphic substitution during the formation of halloysite template. Its magnetic property is mainly attributed to the Ni nanoparticles, not the wires. The metallized ceramic microstructure has the potential to be utilized as a novel magnetic material.     

Kinetic modelling of cadmium removal from phosphoric acid by non-dispersive solvent extraction

In this work it is reported that the kinetic modelling of the separation of cadmium from phosphoric acid by non-dispersive solvent extraction. Using Cyanex 302 as selective extractant, the extraction step was carried out in a hollow fibre module containing polypropylene fibres, whereas the concentration step required a ceramic module with tubular channels due to the high acidity of the backextraction agent. Application of the methodology previously reported by the authors led to the development of a kinetic model with three design parameters, i.e., equilibrium constant of the extraction reaction (K'_e = 6 × 10³ mol⁻²/l⁻²), membrane mass transport coefficient of the extraction module K_me=8.33×10⁻⁸ m/s) and of the backextraction module (K_ms=3.33×10⁻⁸ m/s), that described satisfactorily the behaviour of the separation-concentration system. Thus, in this work a new application of the non-dispersive solvent extraction technology is presented, characterising at the same time the behaviour and parameters of a new type of contactor, i.e., a tubular ceramic module.     

Preparation and properties of surface modified ceramic membranes. Part III. Gas permeation of 5 nm alumina membranes modified by trichloro-octadecylsilane

Stable trichloro-octadecyl silane (ODS) derivatives of a 5 nm γ-alumina ceramic membrane were prepared. Gas permeabilities of the untreated membrane did not show Knudsen diffusion at 20°C. Gas permeabilities of the ODS membrane were three orders of magnitude lower; He, Ne, Ar, CO₂, C₃H₈ have near constant permeabilities 360 mol s⁻¹ m⁻² bar⁻¹, except methane which has the highest permeability of the group, 481 mol s⁻¹ m⁻² bar⁻¹. The mechanism of diffusion is solution/diffusion. Remarkably, permeabilities of ODS-alumina membrane were reduced by 5 X after exposure to a pressure difference of 1 atm (active layer side) against vacuum for only 10 min. The effect was metastable but could be reversed on standing for several hours, reversal of pressure difference or after washing with (hydrocarbon solvent) toluene. The mechanism was presumed to be due to movement of the octadecyl-hydrocarbon chains of the silane monolayer causing a partially blocked pore structure; perhaps a unique example of self-fouling.     

Transport properties of alkanes through ceramic thin zeolite MFI membranes

Polycrystalline randomly oriented defect free zeolite layers on porous α-Al₂O₃ supports are prepared with a thickness of less than 5 μm by in situ crystallisation of silicalite-1. The flux of alkanes is a function of the sorption and intracrystalline diffusion. In mixtures of strongly and weakly adsorbing gases and a high loadings of the strongly adsorbing molecule in the zeolite poze, the flux of the weakly adsorbing molecule is suppressed by the sorption and the mobility of the strongly adsorbing molecule resulting in pore-blocking effects. The separation of these mixtures is mainly based on the sorption and completely different from the permselectivity. At low loadings of the strongly adsorbing molecules the separation is based on the sorption and the diffusion and is the same as the permselectivity. Separation factors for the isomers of butane (n-butane/isobutane) and hexane (hexane/2,2-dimethylbutane) are respectively high (10) and very high (> 2000) at 200°C. These high separation factors are a strong evidence that the membrane shows selectivity by size-exclusion and that transport in pores larger than the zeolite MFI pores (possible defects, etc) can be neglected.     

Titania membrane preparation with chemical stability for very hash environments applications

The high-quality tubular titania MF membranes are successfully prepared by dip-coating techniques and systematically investigated with regard to their corrosive resistances. The experiments show that dispersants PAA and anatase powder were preferably employed to prepare desired suspensions with solid loading 10–15 wt.% and that suspensions properties significantly affect the final membranes quality. The titania MF membranes with pure water permeability 742.42 l m⁻² h⁻¹ bar⁻¹ and 0.1 μm pore diameter have been obtained using the prepared suspensions. The corrosion resistance of titania membranes exhibits that the anatase layers are more stable than the alumina supports in boiling corrosive medium and that the poor quality titania MF membranes become more deteriorated due to its top layer pore blockages and fouling layer formation, which provides a wide range of practical application fields in very hash environments with reliable data supports.