Sonochemical conversion of CO2 into hydrocarbons: The Sabatier reaction at ambient conditions

In this study, we investigated an alternative method for the chemical CO₂ reduction reaction in which power ultrasound (488 kHz ultrasonic plate transducer) was applied to CO₂-saturated (up to 3%) pure water, NaCl and synthetic seawater solutions. Under ultrasonic conditions, the converted CO₂ products were found to be mainly CH₄, C₂H₄ and C₂H₆ including large amount of CO which was subsequently converted into CH₄. We have found that introducing molecular H₂ plays a crucial role in the CO₂ conversion process and that increasing hydrogen concentration increased the yields of hydrocarbons. However, it was observed that at higher hydrogen concentrations, the overall conversion decreased since hydrogen, a diatomic gas, is known to decrease cavitational activity in liquids. It was also found that 1.0 M NaCl solutions saturated with 2% CO₂ + 98% H₂ led to maximum hydrocarbon yields (close to 5%) and increasing the salt concentrations further decreased the yield of hydrocarbons due to the combined physical and chemical effects of ultrasound. It was shown that CO₂ present in a synthetic industrial flue gas (86.74% N₂, 13% CO₂, 0.2% O₂ and 600 ppm of CO) could be converted into hydrocarbons through this method by diluting the flue gas with hydrogen. Moreover, it was observed that in addition to pure water, synthetic seawater can also be used as an ultrasonicating media for the sonochemical process where the presence of NaCl improves the yields of hydrocarbons by ca. 40%. We have also shown that by using low frequency high-power ultrasound in the absence of catalysts, it is possible to carry out the conversion process at ambient conditions i.e., at room temperature and pressure. We are postulating that each cavitation bubble formed during ultrasonication act as a “micro-reactor” where the so-called Sabatier reaction -$C{O}_2+4H_2\stackrel{\mathit{Ultrasonication}}{\to }C{H}_4+2H_{2}O$ - takes place upon collapse of the bubble. We are naming this novel approach as the “Islam-Pollet-Hihn process”.     

First principles investigations of Fe,Co, Ni in model honeycomb carbon networks

The behaviors of ferromagnetic transition metals of the first period: Fe, Co and Ni are examined within density functional theory calculations in two dimensional carbon extended networks using model structure LiC₆. Around geometry optimized structures, the energy-volume equations of states considering non magnetic and spin polarized configurations established ferromagnetic ground states with magnetizations –reduced with respect to the metals’– of 2 μ_B for FeC₆ and 1 μ_B for CoC₆ while no magnetic solution could be identified for NiC₆. In the D_6h point group of the P6/mmm space group l_m decomposition of the d states results with increasing energy into doublet state E_1g with d(x²-y²) and d(xy); singlet state A_1g d(z²) and doublet state E_2g d(xz) and d(yz) lying on E_F and responsible of the onset of magnetic moments. This was mirrored via molecular orbital approach with a construct of Fe embedded between two extended carbon networks thus validating the model structure proposed for TC₆ compounds. The 100% polarization in one spin channel allows proposing potential uses in spintronics applications.     

Towards molecular-scale electronics and biomolecular self-assembly

This paper provides an overview of recent research developments in the field of nanoelectronics with organic materials such as carbon nanotubes and DNA-templated nanowires. Carbon nanotubes and gold electrodes are chemically functionalized in order to contact carbon nanotubes by self-assembly. The transport properties of these nanotubes are dominated by charging effects and display clear Coulomb blockade behaviour. A different approach towards nanoscale electronics is based on the molecular recognition properties of biomolecules such as DNA. As an example, DNA is stretched between electrodes using a molecular combing technique. A two-step metallization procedure leads to the formation of highly conductive gold nanowires.     

Characterizations of Tb:Zn2SiO4 films on silicon wafer prepared by sol-gel dip-coating and solid-phase reaction

Terbium-doped Zn_2SiO_4 films were successfully prepared on Si wafers by a simple sol-gel dip-coating and solid-phase reaction method of ZnO and SiO_2. X-ray diffraction (XRD) and UV－Vis absorption results revealed that films processed below 850℃ were ZnO in wurzite structure, and films processed above 850℃ were Zn_2SiO_4 in wellimite structure. Photoluminescence measurements of the Tb-doped Zn_2SiO_4 films showed two strong emission bands at 490 and 545nm. The photoluminescence lifetime was 4.6ms.     

Diffusion Structural Analysis Study of Titania Films Deposited by Sol-Gel Technique on Silica Glass

The diffusion structural analysis (DSA) was used to characterize microstructure changes of hydrous titania gel films under in situ conditions of heating. TG and DTA were used in order to elucidate the processes controlling the formation of anatase film during heating of hydrous titania gel film. The annealing of porosity and near surface structure defects of the dehydrated titania films was indicated by DSA in the temperature range 255–700°C as the decrease of radon release rate. It was demonstrated that the annealing was enhanced on heating in oxygen in comparison with heating in argon. The DSA experimental results were compared with model curves describing the radon diffusion mobility and the annealing of radon diffusion paths.     

Spectrofluorimetric Method for the Determination of Aluminum with Alizarin Red PS

 A simple and direct spectrofluorimetric method has been developed for the determination of aluminum using alizarin red PS (1,2,4-trihydroxy 9,10-anthraquinone-3-sulfonic acid). The method is based on the strong fluorescence (480/564 nm) of Al³⁺ and alizarin red. Experimental parameters such as pH, concentration of the ligand, ionic strength of the solution, reaction time and temperature were optimized in order to maximize the analytical signal. Interferences of several ions (anions and cations) were studied and evaluated. The linear range of the method extends from 3 to 100 μg L⁻¹. Limit of detection (3s_b) was 0.9 μg L⁻¹. The method was tested with a silicate certified reference material. Interferences were eliminated by a liquid extraction with cupferron. Author for correspondence. E-mail: aucelior@rdc.puc-rio.br Received September 10, 2002; accepted January 15, 2003 Published online May 5, 2003     

New poly(butylene succinate)/layered silicate nanocomposites. II. Effect of organically modified layered silicates on structure,properties, melt rheology,and biodegradability

A series of new poly(butylene succinate) (PBS)/layered silicate nanocomposites were prepared successfully by simple melt extrusion of PBS and organically modified layered silicates (OMLS). Three different types of OMLS were used for the preparation of nanocomposites: two functionalized ammonium salts modified montmorillonite and a phosphonium salt modified saponite. The structure of the nanocomposites in the nanometer scale was characterized with wide-angle X-ray diffraction and transmission electron microscopic observations. With three different types of layered silicates modified with three different types of surfactants, the effect of OMLS in nanocomposites was investigated by focusing on four major aspects: structural analysis, materials properties, melt rheological behavior, and biodegradability. Interestingly, all these nanocomposites exhibited concurrent improvements of material properties when compared with pure PBS. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 3160–3172, 2003     

溶胶-凝胶法制备小颗粒(Y,Gd)BO_3∶Eu及其表征

用溶胶 凝胶方法制备了平均粒径为 1～ 2 μm的小颗粒、高发射效率的 (Y ,Gd)BO3 ∶Eu红色发射荧光体。用XRD、SEM、粒度分析和PL光谱对荧光体作了表征和研究。常规固相反应合成 (Y ,Gd)BO3 ∶Eu需在 1 2 0 0℃以上才能形成均一的固溶体。而溶胶 凝胶法制取稀土正硼酸盐 80 0℃灼烧已可形成均一的单相 (Y ,Gd)BO3 ∶Eu,在 1 1 0 0℃可得到发光亮度最高的荧光体。它的亮度是常规固相反应于 1 2 0 0℃制得的荧光体的 1 2 0 %。采用溶胶 凝胶法制取 (Y ,Gd)BO3 ∶Eu荧光体 ,可在相当宽的实验条件范围内得到小粒径、窄分布和高亮度的荧光体 ,且有良好的颗粒形貌。     

Local adsorption sites and bondlength changes in Ni(1 0 0)/H/CO and Ni(1 0 0)/CO

The local adsorption geometry of CO adsorbed in different states on Ni(1 0 0) and on Ni(1 0 0) precovered with atomic hydrogen has been determined by C 1s (and O 1s) scanned-energy mode photoelectron diffraction, using the photoelectron binding energy changes to characterise the different states. The results confirm previous spectroscopic assignments of local atop and bridge sites both with and without coadsorbed hydrogen. The measured Ni–C bondlengths for the Ni(1 0 0)/CO states show an increase of 0.16 ± 0.04 Å in going from atop to bridge sites, while comparison with similar results for Ni(1 1 1)/CO for threefold coordinated adsorption sites show a further lengthening of the bond by 0.05 ± 0.04 Å. These changes in the Ni–CO chemisorption bondlength with bond order (for approximately constant adsorption energy) are consistent with the standard Pauling rules. However, comparison of CO adsorbed in the atop geometry with and without coadsorbed hydrogen shows that the coadsorption increases the Ni–C bondlength by only 0.06 ± 0.04 Å, despite the decrease in adsorption energy of a factor of 2 or more. This result is also reproduced by density functional theory slab calculations. The results of both the experiments and the density functional theory calculations show that CO adsorption onto the Ni(1 0 0)/H surface is accompanied by significant structural modification; the low desorption energy may then be attributed to the energy cost of this restructuring rather than weak local bonding.     

Synthesis of Dimethyl Carbonate from CO2 , Methanol, and Epoxides Using Re（CO） 5 Cl/K2 CO3 as Catalyst System

IntroductionOver the past few years, dimethyl carbonate(DMC) has been proven to be an efficientmethylating,methoxylating, and methoxycarbonylating agent inorganic syntheses, in which DMC is used to replace thetoxic methyl halides, dimethyl sulfate or carb