溶胶-凝胶制备技术与新型催化材料Ⅲ.溶胶粒子表面修饰方法制备催化膜

提出用溶胶粒子表面修饰方法，结合溶胶凝胶技术制备无机催化膜．该方法的基本原理是利用合适的金属配合物在胶粒表面的吸附作用，经溶胶凝胶过程，将活性组分结合到无机膜中．实验测定结果表明：（ＮｉＥＤＴＡ）２－，ＶＯ－３，ＭｏＯ２－４，（Ｐｄ（ＮＨ３）４）２＋，ＰｄＣｌ２－４，ＰｔＣｌ２－６和ＲｈＣｌ３－６可用来修饰ＡｌＯＯＨ溶胶．以Ｐｄ／γＡｌ２Ｏ３催化膜的制备为例，经三次溶胶凝胶过程，可制得无裂缺的厚度为９μｍ的Ｐｄ／γＡｌ２Ｏ３催化膜，膜材料的平均孔直径为６ｎｍ，Ｐｄ被均匀地分布在膜的顶层，其平均粒径为２３ｎｍ．     

Influence of transition metal ions on the textural properties of alumina and aluminasilicates

Accelerated phase transformations and chemical reactions of metastable aluminas and kaolinite, doped with Cu^{2 +}, Mn^{3 +}/Mn^{2 +} and Fe^{3 +}/Fe^{2 +} ions, are accompanied with accelerated decrease of surface area and pore volume values. The phenomena in metal ion doped samples are explained by a catalytic mechanism, in terms of the Jahn-Teller effect. This revised version was published online in June 2006 with corrections to the Cover Date.     

NMR investigation of concentrated alumina and silica slurries

The longitudinal relaxation times (T₁) of water in concentrated silica and alumina slurries were measured as a function of solids content. It was shown that the results could be fit very well with a two-phase fast-exchange model between free and surface-bound water. As expected, values of T₁ for bound water were in the order of 20–2000 times lower than that for free water, indicating a higher effective viscosity of the surface-bound water. The strength of the interaction depended on the particular surface, and all of the aluminas examined interacted more strongly with water than the two silicas studied, which themselves differed considerably. The chemical mechanical polishing (CMP) removal rate of tantalum by silica slurries was shown to be directly correlated with the interaction parameters, derived from the NMR relation times rather than with total surface hydroxyl group concentration.     

Microcalorimetric Adsorption of Alumina Oxide Catalysts for Combination of Ethylbenzene dehydrogenation and carbon Dioxide Shift-reaction

Styrene (STY) is now produced industrially in fairly large quantities by the dehydrogenation of ethylbenzene (EB) using promoted iron oxide catalyst with superheated steam.In this case, small amount of carbon dioxide formed as a by-product was known to inhibit the catalytic activity of commercial catalyst. Recently, there have been some reports which carbon dioxide showed positive effects to promote catalytic activities on the reaction over several catalysts.In this study, we attempted to combine the dehydrogenation of EB to STY with the carbon dioxide shift-reaction. The combine reaction (EB + CO2 → STY + H2O + CO) can be considered as one of the ways of using CO2 resources and can yield simultaneously STY and Carbon oxide.Alumina oxide catalysts such as Al2O3, Na2O/Al2O3 and K2O/Al2O3 were prepared by the usual impregnation method with an aqueous solution of NaNO3 and KNO3, and then calcined at 650℃ for 5 h in a stream of air. The reaction condition is 600℃, flow of CO2 38ml/mon and space velocity (EB) 1.28h-1.     

Photoluminescence properties of the composite of porous alumina and poly (2,5-dibutoxy-1,4 phenylenevinylene)

The spin coating method was used to assemble polymer (Poly (2,5-dibutoxy-1,4-phenylenevinylene)) (DBO-PPV) into the pores of porous alumina which was prepared by anodization. Four peaks in the photoluminescence (PL) spectra of the composite, with contributions from the DBO-PPV and porous alumina, were found. It was also found that the light emitting from the porous alumina could excite the photoluminescence of DBO-PPV. The nanometer effect of the porous alumina can lead to a blue shift of 90 nm of the PL peaks of DBO-PPV.     

Characterization of ceramic PVD thin films on AZ31 magnesium alloys

Ceramic thin films have been widely used to protect the metal substrate as coatings in the past years. In order to improve the poor corrosion resistance of AZ31 magnesium alloy, the study in this paper used the electron beam evaporation method to prepare ceramic PVD films on its surface with TiO₂ and Al₂O₃ as donors, respectively. Atomic force microscopy (AFM), scanning electron microscope (SEM), energy dispersive X-ray spectrometer (EDS), Auger electron spectroscopy (AES) and X-ray diffraction (XRD) were used to investigate the surface morphology, composition and microstructure of the thin films. Both films deposited on AZ31 took on compact top surface morphologies and grew as amorphous structures on substrate. AES test not only showed that films compositions deviated the standard stoichiometric ratios, but also found that element Mg diffused into films and existed as magnesium oxide in the TiO_x film as well as the AlO_x film. In the electrochemical corrosion test, the AlO_x coating on AZ31 exhibited the largest electrochemical impedance in a 3.5% NaCl solution. But it did not show better corrosion resistance than others for the poorer adhesion. Even if its thickness was small, the TiO_x coating on AZ31 exhibited the best corrosion resistance in this study. According to the observation and analysis, the damage of these films on AZ31 in aggressive solutions was mainly due to the existence of pores, microcracks, vacancies and poor adhesion between coating and substrate.     

The coexistence of γ(γ′) and θ alumina observed by STM and LEED on top of oxide layer grown on CoAl(1 0 0)

We report the coexistence of γ(γ′) and θ alumina grown on the CoAl(1 0 0) surface. Both phases were observed after annealing of alumina at 1150 K by means of scanning tunnelling microscopy (STM). The crystal structures of γ(γ′) and θ alumina were indexed based on low energy electron diffraction (LEED) and STM experimental data.     

甲醇与乙醇一步合成异丁醛用CuO-ZnO/Al2O3催化剂

在ＣｕＯ－ＺｎＯ／Ａｌ２Ｏ３催化剂上，甲醇与乙醇在常压和２１０￣３６０℃温度下一步反应合成异丁醛。利用正交设计方法，研究了ＣｕＯ－ＺｎＯ／Ａｌ２Ｏ３体系催化剂组成和制备条件等因素对催化剂催化性能的影响。结果表明，催化剂中ＣｕＯ含量对催化剂的催化活性影响最大，而ＺｎＯ含量则主要影响催化剂对异丁醛的选择性。催化剂制备条件，如沉淀温度、陈化时间等，也不同程度也影响催化剂的催化性能。ＸＲＤ和ＢＥＴ表征结果     

Chromium and yttrium-doped magnesium aluminum oxides prepared from layered double hydroxides

Layered double hydroxides with the hydrotalcite-like structures, containing Mg²⁺ and Al³⁺, doped with Cr³⁺ and Y³⁺, have been prepared by precipitation at constant pH. The weight percentages of Cr³⁺ and Y³⁺ were 1, 2, or 3%, and 0.5 or 1%, respectively. Single phases were obtained in all cases, whose crystallinity decreased as the content in Cr and Y was increased. The solids have been characterised by element chemical analysis, powder X-ray diffraction, thermal analyses (differential, thermogravimetric and programmed reduction), FT-IR and UV–vis spectroscopies; the specific surface areas have been determined from nitrogen adsorption isotherms at −196 °C. Upon calcination at 1200 °C for 5 h in air all solids display a mixed structure (spinel and rock salt for MgO); these solids have also been characterised by these techniques and their chromatic coordinates (CIE – L^*a^*b^*) have been determined. Their pink colour makes these solids suitable for being used as ceramic pigments.     

γ-Al2O3对NiB合金的催化及表面性能的影响

集），Dalian（大连）：1994，p.262||8LiuWeicheng（刘伟成），YanJingqing（晏荆青），JiangBingnan（姜炳南）．CuihuaXuebao（催化学报），1990，||11（2）：929HuCW，WangWZXuGY，etal．J．Nat．GasChem，1994,（3）：194||