三价锰离子引发烯类单体在聚乙烯醇上接枝聚合的研究

<正> 无论是淀粉;纤维素,还是聚乙烯醇(PVA)的接枝反应,Ce(Ⅳ)被认为是一个十分有效的引发剂,已有较详尽的研究。与Ce(Ⅳ)相类似,Mn(Ⅲ)也可以和一些高聚物组成氧化还原引发体系,由此产生自由基,引发烯类单体在高分子主干上进行接枝聚合。Ranby等人,以焦磷酸络合的三价锰离子引发烯类单体在纤维素和淀粉的接枝反应中,获得了高效的接枝产物。有用这种引发体系在淀粉上接枝丙烯腈获得吸水276     

Density and viscosity of three (2,2,2-trifluoroethanol + 1-butyl-3-methylimidazolium) ionic liquid binary systems

Densities and viscosities were determined for binary mixtures of 2,2,2-trifluoroethanol (TFE) and 1-butyl-3-methylimidazolium tetrafluoroborate ([bmim][BF₄]), 1-butyl-3-methylimidazolium hexafluorophosphate ([bmim][PF₆]) or 1-butyl-3-methylimidazolium bis(trifluoromethanesulfonyl)imide ([bmim][NTf₂]) over the entire range of composition. The experimental measurements were carried out at temperatures ranging from 278.15 K to 333.15 K, at atmospheric pressure. The densities and viscosities of the pure ionic liquids and their mixtures with TFE were described successfully by an empirical third-order polynomial and by the Vogel–Fulcher–Tammann equation, respectively. In addition, excess molar volumes and viscosity deviations were determined from densities and viscosities of mixtures, respectively, and fitted by using the Redlich–Kister equation.     

Effect of laser energy on the deformation behavior in microscale laser bulge forming

Microscale laser bulge forming is a high strain rate microforming method using high-amplitude shock wave pressure induced by pulsed laser irradiation. The process can serve as a rapidly established and high precision technique to impress microfeatures on thin sheet metals and holds promise of manufacturing complex miniaturized devices. The present paper investigated the forming process using both numerical and experimental methods. The effect of laser energy on microformability of pure copper was discussed in detail. A 3D measuring laser microscope was adopted to measure deformed regions under different laser energy levels. The deformation measurements showed that the experimental and numerical results were in good agreement. With the verified simulation model, the residual stress distribution at different laser energy was predicted and analyzed. The springback was found as a key factor to determine the distribution and magnitude of the compressive residual stress. In addition, the absorbent coating and the surface morphology of the formed samples were observed through the scanning electron microscope. The observation confirmed that the shock forming process was non-thermal attributed to the protection of the absorbent coating.     

Reducing Occupational Noise Propagated from Centrifugal Fan through Dissipative Silencers: A Field Study

Acoustic performance of dissipative silencer was evaluated to determine the effectiveness of perforated duct porosity and absorbent material density in reducing occupational noise exposure propagated from centrifugal fan. Design charts were applied to predict noise reduction and length of a dissipative silencer. Dissipative silencers with various punched duct porosity (14%, 30% and 40%) and sound absorbent density (80 Kg/m³, 120 Kg/m³, and 140 Kg/m³) were designed and fabricated. According to ISO9612 and ISO11820, noise level was measured before and after installing all nine test silencers at fixed workstations around the discharge side of a centrifugal fan in a manufacturing plant. On average, the noise level at the discharge side of a fan without silencer was measured to be 93.6 dBA, whereas it was significantly mitigated by 67.4 dBA to 70.1 dBA after installing all silencers. Dynamic insertion loss for a dissipative silencer with 100 cm length was predicted to be 27.9 dB, which was in agreement with experimental ones. Although, there was no significant differences between insertion loss of silencers, the one with 30% porosity and 120 Kg/m³ rock wool density had the highest insertion loss of 26.2 dBA. Dissipative silencers noticeably reduced centrifugal fan noise exposures. Increasing sound absorbent density and duct porosity up to a certain limit could probably be effective in noise reduction of dissipative silencers.     

ICP-AES测定果核活性炭中的磷

用ICP-AES测定果核活性炭中的磷,检出限为0.8μg/mL;精密度RSD为1.1%—7.8%;加标回收率为95.5%—105%。     

基于新型交联聚合物电解质的准固态染料敏化太阳能电池

采用柠檬酸(CA)交联聚乙二醇(oligo-PEG, 平均分子量M_w=200, 400, 1000, 2000), 合成具有可生物降解性能的聚柠檬酸-乙二醇(PCE)交联聚酯, 并以此为基体材料制备得到准固态的三维交联型PCE/LiI/I₂聚合物电解质. 采用红外吸收光谱(IR)、核磁共振氢谱(¹H-NMR)、扫描电镜(SEM)和Raman光谱分别对PCE基体的分子结构、聚合物电解质的微观形貌以及导电离子对的存在形式进行表征; 通过线性扫描伏安法(LSV)研究了聚合物电解质的离子扩散系数、电导率以及电池的输出电流-电压(I-V)性能. 结果表明, PEG的分子量影响PCE基体膜的微观形貌及其吸液性能, 从而影响聚合物电解质的离子导电性能及电池的光电性能: 随着PEG分子量M_w从200, 400, 1000增大到2000, PCE基体膜的结构变得疏松, 吸液率增加, 吸液溶胀后的基体中I-3的跃迁活化能降低, 导致电解质的电导率和电池的短路光电流密度随之增加; 在60 mW·cm^-2的入射光强下, 四种电解质对应电池的光电转化效率依次为3.26%、3.34%、4.26%和4.89%.     

Enantiomeric analysis of beta-pinene and limonene by direct coupling of reversed phase liquid chromatography and gas chromatography using absorbents as packing materials

A method based on the use of absorbents as packing materials inside the interface of the online coupling between RPLC and GC is proposed for the enantiomeric analysis of beta-pinene and limonene in essential oils. For that purpose, a comparison of the RSD, detection limit and recovery provided by two absorbents and one adsorbent is included in this study. The results found in this work proved the validity of absorbents as packing materials in online RPLC-GC to determine minor compounds in complex matrices. In particular, PDMS seemed to be specially useful to analyse nonpolar compounds, such as beta-pinene and limonene, since it provided higher sensitivity for this kind of compounds. The developed method was applied to the evaluation of the natural and non-natural character of commercial essential oils by means of the determination of the enantiomeric composition of beta-pinene and limonene.     

Synthesis and characterization of Zn(O,OH)S and AgInS2 layers to be used in thin film solar cells

In this paper AgInS₂ and Zn(O,OH)S thin films were synthesized and characterized. AgInS₂ layers were grown by co-evaporation from metal precursors in a two-step process, and, Zn(O,OH)S thin films were deposited from chemical bath containing thiourea, zinc acetate, sodium citrate and ammonia. X-ray diffraction measurements indicated that AgInS₂ thin films grown with chalcopyrite structure, and the as-grown Zn(O,OH)S thin films were polycrystalline. It was also found that the AgInS₂ films presented p-type conductivity, a high absorption coefficient (greater than 10⁴ cm⁻¹) and energy band-gap E_g of about 1.95 eV, Zn(O,OH),S thin films presented E_g of about 3.89 eV. Morphological analysis showed that under this synthesis conditions Zn(O,OH),S thin films coated uniformly the absorber layer. Additionally, the Zn(O,OH)S kinetic growth on AgInS₂ layer was studied also. Finally, the results suggest that these layers possibly could be used in one-junction solar cells and/or as top cell in a tandem solar cell.     

泡塑富集发射光谱法连测化探样品中超痕量金、铂、钯

为实现化探方法直接寻找贵金属金、铂、钯。需要一种操作简便、检出限低、对设备无特殊要求的分析方法。本文研究了泡塑富集发射光谱法连测化样品超痕量金、铂钯的方法。方法用于贵州省二级标准样的测定,结果与推荐值相符。     

对甲氧基肉桂酸异辛酯-β-环糊精包合物的制备及稳定性

采用饱和水溶液法制备了UVB型紫外线吸收剂对甲氧基肉桂酸异辛酯-β-环糊精包合物,经红外光谱、热重、差示扫描量热对包合物进行了鉴定,证实了包合物的形成。紫外光谱分析表明包合没有改变对甲氧基肉桂酸异辛酯的性质,包合物仍具有吸收紫外线的能力;包合作用增强了对甲氧基肉桂酸异辛酯在乙醇-水混合溶液中的稳定性;热分析表明对甲氧基肉桂酸异辛酯-β-环糊精包合物具有良好的热稳定性。