Designing Semipermeable Hydrogel Shells with Controlled Thickness through Internal Osmosis in Triple-Emulsion Droplets

Hydrogel shells that compartmentalize the water core from the aqueous surrounding provide molecular selectivity on size and charge in transmembrane transport. It is highly demanding to produce thin hydrogel shells to minimize diffusion length and maximize core volume. Here, internal osmosis in water-in-oil-in-water-in-oil (W/O/W/O) triple-emulsion droplets is used to produce thin hydrogel shells enclosing a large water core. The triple-emulsion droplets are prepared to have an ultrathin middle oil layer using a capillary microfluidic device. The innermost water droplet has a higher osmolarity than the outer water layer containing photopolymerizable hydrogel precursors, which pumps water from the outer layer to the core through the ultrathin oil layer by the osmosis. Therefore, the outer layer gets thinner and hydrogel precursors are enriched while the size of the triple-emulsion droplets remains unchanged. Through photopolymerization of precursors and phase transfer from oil to water, hydrogel shells enclosing water core are produced in the water environment; the oil layer is ruptured for molecular exchange through the shells. The thickness and composition of the hydrogel shells are precisely controllable by the osmotic conditions. The shells show a high permeation rate due to the thinness as well as controlled cut-off threshold of permeation for neutral and charged molecules.     

Strategies for synthesizing non-bioaccumulable alternatives to PFOA and PFOS

This minireview describes the strategies for synthesis of fiuorinated surfactants potentially nonbioaccumulable.Various strategies have been focused on(Ⅰ) reducing the length of the perfluorocarbon chain,(Ⅱ) introducing hetero atoms into the fluorocarbon chain,(Ⅲ) introducing branch(herein and after branch means the fluoro-carbon chain section is not straight).In most cases,the surface tensions versus the surfactant concentrations have been assessed.These above strategies led to various highly fiuorinated(perfluorinated or not perfluorinated) surfactants whose chemical changes enabled to obtain novel alternatives to perfluorooctanoic acid(PFOA) and perfluorooctane sulphonate(PFOS).     

The Effect of the Spacer of Bis(biurea) Ligands on the Structure of A2L3‐type (A=anion) Phosphate Complexes

By tuning the length and rigidity of the spacer of bis(biurea) ligands L, three structural motifs of the A₂L₃ complexes (A represents anion, here orthophosphate PO₄^3?), namely helicate, mesocate, and mono‐bridged motif, have been assembled by coordination of the ligand to phosphate anion. Crystal structure analysis indicated that in the three complexes, each of the phosphate ions is coordinated by twelve hydrogen bonds from six surrounding urea groups. The anion coordination properties in solution have also been studied. The results further demonstrate the coordination behavior of phosphate ion, which shows strong tendency for coordination saturation and geometrical preference, thus allowing for the assembly of novel anion coordination‐based structures as in transition‐metal complexes.     

机载光电雷达它机试飞技术研究

机载光电雷达受平台及大气环境影响较大,而它机试飞能有效规避研制风险,是产品研制的必经阶段。本文介绍了机载光电雷达它机试飞试验系统组成、试验流程和数据处理等内容。经工程验证,实施过程满足任务需求,对其他光电系统的它机及本机试飞具有参考价值。     

基于三相幅度测量的相控阵天线快速校准方法

提出了一种基于三相幅度测量的相控阵天线快速校准方法。该方法将天线阵列进行分组,利用每种分组在三种配相下的阵面合成场幅度测量值,可解算出各个天线单元的初始幅相值。该方法仅需幅度测量,避免了相位测量误差影响单元幅相值的计算精度,而且所需幅度测量次数仅为(2N+1)次,可显著提高校准时效性。另外,利用分组思想,同时改变多个单元相位,使总辐射场的幅度变化显著,提升校准准确性。仿真结果表明:校准后相位均方根误差为2.2°,幅度均方根误差为0.2 dB。     

面源红外诱饵对抗红外制导导弹干扰策略研究

面源红外诱饵使用的过程中,合理有效的干扰策略是干扰红外制导导弹的关键,针对这一问题,通过理论分析与仿真模拟相结合得到面源红外诱饵对抗红外制导导弹的干扰策略。首先以红外成像制导导弹为例,介绍红外制导导弹的仿真模型,然后将攻击过程分为锁定前与锁定后,以命中率为评价指标,得到两个阶段下的最佳干扰策略,包括诱饵的最佳释放时机、释放间隔以及载机应采取的机动动作等。     

二极管侧面抽运薄片激光器耦合系统研究

设计了二极管侧面抽运Nd:YAG薄片激光器,耦合系统由消像差透镜组和空心光波导组成,对二极管快轴和慢轴方向的抽运光进行压缩和均匀化.采用光线追迹法,同时考虑二极管在快轴和慢轴方向的发散特性及薄片侧面的散射特性,模拟并分析了光线在耦合系统内的传输和薄片内抽运光分布的规律.模拟结果表明耦合系统具有98.1%的耦合效率,同时薄片内具有理想的抽运光分布.     

纳米AlN粉末的制备与烧结

利用低温燃烧合成前驱物制备出平均粒度为100 nm的AlN陶瓷粉末,比较了该粉末的常压烧结和放电等离子烧结的特性.实验表明:以合成的AlN粉末为原料,添加5%(质量比)Y2O3作为烧结助剂,在常压、流动N2气氛下1600℃保温3 h,制备出平均晶粒尺寸为4～8 μm、密度为3.28 g·cm-3的AlN陶瓷;将同样的粉末不加任何烧结助剂,采用SPS技术在1600℃保温4 min,得到密度为3.26 g·cm-3的AlN陶瓷,晶粒度约为1～2μm.