A multiaxial elastic potential with error-minimizing approximation to rubberlike elasticity

This study is concerned with a new,explicit approach by means of which forms of the large strain elastic potential for multiaxial rubberlike elasticity may be obtained based on data for a single deformation mode.As a departure from usual studies,here for the first time errors may be estimated and rendered minimal for all possible deformation modes and,furthermore,failure behavior may be incorporated.Numerical examples presented are in accurate agreement with Treloar's well-known data.     

Fréchet空间上的一些等距逼近问题

本文主要讨论Ｆｒéｃｈｅｔ空间上ε－等距线性算子的等距逼近问题，证明了任意有限维Ｆｒéｃｈｅｔ空间之间的等距逼近问题都是肯定的；无穷维Ｆｒéｃｈｅｔ空间（ｓ）空间上的等距逼近问题也是肯定的．     

油水两液相一维非等温渗流的传递分析

在求解油水两液相非等温渗流的温度场、压力场基础上,以驱动功、驱动功率、驱动阻力、驱动速率为特征参数,对该过程进行(火用)传递分析。数值模拟的结果表明:含水通过降低油的相对渗透率、从而增大驱动阻力、减小驱动功率, 最终导致原油产量降低。     

我国上市公司资本结构决策的实证研究

本在已有资本结构理论研究成果的基础上，对30家沪市上市公司的资本结构进行了实证研究，提出了在我国资本市场环境下优化企业资本结构的对策建议。     

1+1/2对转涡轮叶排轴向间距对性能影响的研究

木文对1+1/2对转涡轮中轴向间距影响进行了初步研究。对不同轴向间距叶栅流场进行了大量时间精确模拟。研究表明,1+1/2对转涡轮高低压转叶间轴向间距成为追求高效率的制约因素,轴向间距为高压转叶喉部宽度是关键点。因此有关小轴向间距下强激波/叶排干扰的研究应该加强。     

As+注入硅的紫外-可见椭圆偏振光谱

本文采用椭圆偏振光谱法研究了剂量为1×10¹⁶—3×10¹²cm^-2的As⁺注入硅,及其在700℃退火后的光学性质。得出:当As⁺注入剂量增大到某一程度后,便呈非晶特性。低于临界剂量的样品,其n-λ,ε₂-λ关系曲线随剂量的增大而往下方移动,呈有规律变化;退火后,在大于4000?波段,n-λ与ε₂-λ曲线基本恢复到单晶硅状态。但在小于4000?的紫外区却未完全恢复,注入剂量越大,偏离单晶硅就越大。并指出,紫外光区是离子注入硅的信息敏感区;用有效质量模型计算出注入剂量与损伤度的关系。计算结果与实验符合得较好。 关键词：     

光纤的能量传输特性及应用

着重分析了影响光纤传输能量以及光纤传输中造成能量损耗的因素。这些因素主要包括光纤材料、构造、光纤的折射率分布、光纤的长度和芯径、光纤的数值孔径和热效应以及耦合等。同时 ,结合激光二极管点火的实例 ,分析探讨了其背景和应用价值。结论是 :为了尽可能减少能量损耗、提高光纤输出的激光功率和激光功率密度 ,应当选取合适的激光工作波长、较小的光纤长度、较小的芯径和较小的数值孔径 ,应采用渐变折射率分布光纤 ,应减少弯曲与耦合     

非Chetaev型变质量非完整系统的Lie对称性与Noether对称性

研究非Chetaev型变质量非完整系统的Lie对称性与Noether对称性以及其间的 关系,给出Lie对称性导致Noether对称性以及Noether对称性导致Lie对称性的条件.     

Modelling of a single drop impact onto liquid film using particle method

The process of single liquid drop impact on thin liquid surface is numerically simulated with moving particle semi‐implicit method. The mathematical model involves gravity, viscosity and surface tension. The model is validated by the simulation of the experimental cases. It is found that the dynamic processes after impact are sensitive to the liquid pool depth and the initial drop velocity. In the cases that the initial drop velocity is low, the drop will be merged with the liquid pool and no big splash is seen. If the initial drop velocity is high enough, the dynamic process depends on the liquid depth. If the liquid film is very thin, a bowl‐shaped thin crown is formed immediately after the impact. The total crown subsequently expands outward and breaks into many tiny droplets. When the thickness of the liquid film increases, the direction of the liquid crown becomes normal to the surface and the crown propagates outward. It is also found that the radius of the crown is described by a square function of time: r_C = [c(t ? t₀)]^0.5. When the liquid film is thick enough, a crown and a deep cavity inside it are formed shortly after the impact. The bottom of the cavity is initially oblate and then the base grows downward to form a sharp corner and subsequently the corner moves downward. Copyright © 2004 John Wiley & Sons, Ltd.