膜流动电位测试中Ag-AgCl电极的制备及稳定性研究

膜的动电特性研究中,往往采用流动电位方法。该方法中,Ag-Ag Cl测试电极的质量是影响测试准确性的关键要素。本文采用正交试验设计和方差分析,着重考察电解法制备Ag-Ag Cl电极过程中,电流强度(I)、氯化时间(t)、电解质溶液浓度(CHCl)、电极来源(n)、烘烤温度(T)、活化电极溶液浓度(CKCl)等因素对Ag-Ag Cl电极稳定性的影响。得到Ag-Ag Cl电极的最优制备参数为:电流密度3.0m A/cm2,氯化时间50min,盐酸浓度0.1mol·L-1,烘烤温度120℃,活化电极溶液(KCl)浓度0.001mol·L-1;最显著影响因素为电极来源,显著影响因素为氯化时间和烘烤温度。对最优条件组合下制备的AgAg Cl电极,进行了稳定性实验,结果表明:制备的电极具有较好的稳定性,24h内电极电位漂移量小于0.10mv,7天内电极电位漂移量小于0.2mv;在聚偏氟乙烯中空纤维超滤膜流动电位测试中,流动电位与流动压差具有良好的线性和可重复性,回归曲线R20.99,变化规律符合Helmholtz-Smoluehowski公式,可以较好满足膜的流动电位测试要求。     

镁掺杂氧化铈整体式催化剂催化CO2和CH3OH直接合成碳酸二甲酯

采用共沉淀法成功地合成了不同Mg掺杂量的Ce_1-xMg_xO₂(x=0.05、0.10、0.15、0.20)固溶体催化材料,并运用透射电子显微镜(TEM)、X射线衍射(XRD)、氮气吸附-脱附测试、拉曼光谱、X射线光电子能谱(XPS)、CO₂程序升温脱附(CO₂-TPD)等技术对这些材料进行了表征。结果发现,通过调控CeO₂晶格中Mg的含量,可以调控所制备的Ce_1-xMg_xO₂催化材料的粒径、比表面积、表面缺陷等。其中Ce_0.90Mg_0.10O₂展现了最佳的表面性质,具有最小的平均粒径(约5.8 nm),最大的比表面积(约136 m2·g^-1)以及最高的表面氧含量(31.98%)。将Ce_1-xMg_xO₂催化材料涂覆在堇青石蜂窝陶瓷上制成整体催化剂,考察其对CO₂和CH₃OH直接合成碳酸二甲酯的催化性能。在140℃、2.4 MPa、反应2 h的条件下,Ce_0.90Mg_0.10O₂整体催化剂上碳酸二甲酯的收率高达20.21%,催化效果明显优于CeO₂和其余的Ce_1-xMg_xO₂(x=0.05、0.15、0.20)催化材料。     

4-氨基-7-硝基苯并-2-氧杂-1,3-二唑类衍生物的合成及其对汞离子的识别研究

以4-氯-7-硝基苯并-2-氧杂-1,3-二唑、乙二胺和溴乙酸乙酯等为原料,合成4-氨基-7-硝基苯并-2-氧杂-1,3-二唑类衍生物(NBD-OEt),通过IR、NMR和MS对其进行结构表征。研究NBD-OEt的吸收光谱和荧光光谱性质,探讨其在H2O/EtOH(60/40, V/V) pH 7.40的HEPES缓冲体系中对Hg₂ 的响应,以及NBD-OEt与Hg₂ 的结合模式。结果表明, 随Hg₂ 的不断加入可诱使NBD-OEt在476nm的吸收峰红移至514nm,并有两个等吸收点(347nm、482nm);其荧光发射峰由536nm红移至559nm,且在525nm出现等发射点;通过Job plot法测定NBD-OEt与Hg₂ 以1:1的计量比结合。     

Analysis of ultrasonic guided waves propagating in long bones and cortical thickness based on time-frequency methods

The ultrasonic signals in long bones contain multiple guided modes which are mutual superposed.The velocities of guided waves in long bones are very sensitive to cortical thickness (CTh).In this paper,Hilbert-Huang transform(HHT) was proposed to analyze multi-mode guided waves,which can decompose superposed waves into many independent modes.Then the group velocity of each mode was obtained at corresponding frequency,which was compared with the results of short time Fourier transform(STFT).The CTh was also obtained by comparing with the theoretical calculation.The results showed that the experimental determined thickness was in agreement with the actual CTh,indicating that measuring the velocity of the guided mode can be used to estimate the CTh.The HHT is an effective method to identify multimode guided waves.     

基于时频分布的盲信号分离方法研究长骨中的多模式导波信号

由于超声导波对长骨皮质骨的材料特性及厚度变化非常敏感,因此用导波评价长骨状况的研究已成为近年来的一个研究热点.在接收到的导波中,往往多种模式混叠在一起,使得进一步求取每种导波模式的群速度等与骨质状况密切相关的参数时遇到困难.本文采用基于时频分布的盲信号分离(TFBSS)方法对长骨中混叠的多模式进行分离,然后对分离后的单...     

反胶束固定化醇脱氢酶的制备及应用研究

研究十六烷基三甲基溴化铵(CTAB)-辛烷-己醇反胶束体系固定化醇脱氢酶(ADH)的制备及应用。考察了含水量、CTAB和己醇用量对于ADH固定化的影响。对游离酶和固定化酶的催化动力学性质研究表明:酶促反应的最适pH值分别为8.2和8.8,最适温度分别为31℃和20℃,米氏常数分别为12mmol/L和7mmol/L。30℃时,游离酶存放150min后失活90%,固定化酶失活50%,表明反胶束固定化ADH有较好的热稳定性。应用此体系测定了试样中乙醇的含量。     

基于加权mean-shift可见光/红外双通道目标跟踪

为提高目标亮度突变时的跟踪性能,在每一帧进行目标跟踪时,首先提取可见光图像的颜色特征,红外图像的垂直投影图像和水平投影图像特征,然后利用可见光/红外各自通道的Bhattacharyya系数计算该通道的权值,并对加权mean-shift双通道跟踪方法进行了推导,提出了基于加权mean-shift可见光/红外双通道目标跟踪算法.该方法使前后两帧目标相似度大的通道取大的权值,从而达到有效利用各通道有利信息、提高跟踪性能的目的.实验表明,用本文提出的算法进行可见光/红外双通道目标跟踪时,与基于mean-shift单通道(可见光或红外)目标跟踪算法相比,可提高目标跟踪的准确度,特别是当目标进入树荫区域,引起目标亮度发生显著变化时,跟踪性能基本不受影响.     

ON THE SUSTAINABLE GROWTH IN AN ECONOMY WITH PERFECTLY SUBSTITUTABLE EXHAUSTIBLE RESOURCES

Abstract A model of sustainable economic growth in an economy with two types of exhaustible resources is analyzed. The resources are assumed to be perfect substitutes with marginal rate of substitution varying over time. The optimal control framework is used to characterize the optimal paths under the maximin criterion. It is shown that the resource with increasing productivity is not used before the constant productivity resource is depleted. Afterwards the resource with an increasing productivity is asymptotically depleted as well. The results are based on an assumption that transversality conditions hold. A new sufficient condition for the transversality conditions is derived. Finally, an analogue of Hartwick’s rule for this non‐autonomous case is established.     

Effect of selected signals of interest on ultrasonic backscattering measurement in cancellous bones

This study examined how the signals of interest (SOI) effect on the backscattering measurement numerically based on 3-D finite-difference time-domain (FDTD) method. High resolution microstructure mappings of bovine cancellous bones provided by micro-CT were used as the input geometry for simulations. Backscatter coefficient (BSC), integrated backscatter coefficient (IBC) and apparent integrated backscatter (AIB) were calculated with changing the start (L1) and duration (L2) of the SOI. The results demonstrated that BSC and IBC decrease as L1 increases, and AIB decreases more rapidly as L1 increases. The backscattering parameters increase with fluctuations as a function of L2 when L2 is less than 6 mm. However, BSC and IBC change little as L2 continues to increase, while AIB slowly decreases as L2 continues to increase. The results showed how the selections of the SOI effect on the backscattering measurement. An explicit standard for SOI selection was proposed in this study and short L1 (about 1.5 mm) and appropriate L2 (6 mm-12 mm) were recommended for the calculations of backscattering parameters.