Solid-liquid extraction and preconcentration of trace nickel using 2-nitroso-1-naphthol-4-sulfonic acid (Nitroso-S) and TDBA onto benzophenone and determination by atomic absorption spectrometry.

Nickel was quantitatively retained by 2-nitroso-1-naphthol-4-sulfonic acid (Nitroso-S) and tetradecyldimethylbenzylammonium chloride (TDBA Cl) onto benzophenone in the pH range 5.0-6.0 from large volumes of aqueous solutions of various samples. After filtration, each solid mass consisting of a nickel complex and benzophenone was dissolved with 5 ml of dimethylformamide (DMF) and the metal was determined by atomic absorption spectrometry (AAS). About 0.6 microg of nickel could be concentrated from 200 ml of an aqueous sample, where its concentration was as low as 3.0 ng/ml. Eight replicate determinations of 2.5 microg/ml of nickel in the final DMF solution gave a mean absorbance of 0.112 with a relative standard deviation of 1.9%. The sensitivity for 1% absorption was 98 ng/ml. The interference of a number of anions and cations was studied and the developed optimized conditions were utilized for the trace determination of nickel in various alloys and biological samples.     

Sensing of Trace Amounts of Dodecyl Benzene Sulfonate by Solid Phase Spectrophotometry

A very simple, selective and sensitive spectrophotometric method for the determination of dodecyl benzene sulfonate (DBS) has been investigated. In this method, the ion pair of DBS and methylene blue was adsorbed onto plasticized poly(vinylchloride) membrane as a solid phase extraction medium. The absorbance of the blue membrane was measured at 660nm against a blank membrane using a spectrophotometer. The influence of type and amount of plasticizer, pH, concentration of methylene blue, temperature of sample solution and time of extraction on the absorbance of membrane was studied. Linear calibration was obtained over a concentration range of 0.1 to 6.5µgmL^–1 of DBS. The method was applied to the determination of DBS in different commercial detergents. The precision and accuracy of the method is comparable with the conventional standard method. This method is cost-effective, and the use of organic solvent such as chloroform is completely eliminated.     

OXIDATIVE DEPROTECTION OF TRIMETHYLSILYL ETHERS WITH HEXAMETHYLENETETRAMINEBROMINE SUPPORTED ONTO SILICA GEL UNDER MICROWAVE IRRADIATION IN SOLVENTLESS SYSTEM

Hexamethylenetetramine-bromine supported onto[3pc] silica gel rapidly converts trimethylsilyl ethers to their corresponding carbonyl compounds under microwave irradiation in solventless system.     

Microwave Assisted Synthesis of Dibenzoxazepines

Dibenzo[b,f][1,4]oxazepine derivatives were synthesized in good yields and short reaction times by the reaction of 2‐chlorobenzaldehydes and 2‐aminophenoles in basic conditions under microwave irradiation.     

Modified dispersive liquid-liquid microextraction for pre-concentration of benzene, toluene, ethylbenzene and xylenes prior to their determination by GC

We have developed a modified method for the extraction and preconcentration of benzene, toluene, ethylbenzene and xylenes (BTEX) in aqueous samples. It based on dispersive liquid-liquid microextraction along with solidification of floating organic microdrops. The dispersion of microvolumes of an extracting solvent into the aqueous occurs without dispersive solvent. Various parameters have been optimized. BTEX were quantified via GC with FID detection. Under optimized conditions, the preconcentration factors range from 301 to 514, extraction efficiencies from 60 to 103 %, repeatabilities from 2.2 to 4.1 %, and intermediate precisions from 3.5 to 7.0 %. The relative recovery for each analyte in water samples at three spiking levels is >85.6 %, with a relative standard deviation of <7.4 %.

Determination of organochlorine pesticides in river water using dispersive liquid–liquid microextraction and gas chromatography–electron capture detection

Dispersive liquid–liquid microextraction (DLLME) coupled with gas chromatography–electron capture detection (GC–ECD), has been developed for the extraction and determination of 14 organochlorine pesticides (hexachlorocyclohexanes (α-HCH, β-HCH and δ-HCH), Lindane (γ-HCH), Aldrin, Dieldrin, Endrin, Heptachlor, Heptachlor epoxide, α-Chlordane, β-Chlordane and p,p′-DDT, p,p′-DDD, p,p′-DDE) in river water samples. Factors relevant to the microextraction efficiency, such as the kind of extraction and disperser solvent, their volume and the salt effect was investigated and optimised. In this method the appropriate mixture of extraction solvent (13.5 µL carbon disulphide) and disperser solvent (0.50 mL acetone) were rapidly injected into the aqueous sample by syringe. The values of the detection limit of the method were in the range of 0.05–0.001 µg L^?1, while the relative standard deviations for five replicates varied from 2.7 to 9.3%. A good linearity (0.9894 ≤ r ² ≤ 0.9998) and a broad linear range (0.01–200 µg L^?1) were obtained. The method exhibited enrichment factors ranging from 647 to 923, at room temperature. The relative standard deviations varied from 2.7 to 9.3% (n = 5). The relative recoveries of each pesticide from water samples at spiking levels of 2.00 and 10.0 µg L^?1 were 88.0–111.0% and 95.8–104.1%, respectively. Finally, the proposed method was successfully utilised for the preconcentration and determination of the organochlorine pesticides in the Jajrood River water samples.     

Analysis of tamoxifen and its main metabolites in plasma samples of breast cancer survivor female athletes: Multivariate and chemometric optimization

A sensitive method based on liquid chromatography combined with a diode array detector was developed and validated to simultaneously determine tamoxifen, and its active metabolites N-desmethyltamoxifen, 4-hydroxytamoxifen, and endoxifen in human plasma samples. The green and sustainable vortex-assisted dispersive liquid-phase microextraction technique based on the natural hydrophobic deep eutectic solvent was used for the extraction and preconcentration of the analytes. Chemometrics and multivariate analysis were used to optimize the independent variables including the type and volume of deep eutectic solvent, extraction time, and ionic strength. Under optimal conditions, calibration curves were linear in a suitable range with the lower limits of quantification (0.8–10.0 μg/L), which covered the relevant concentrations of the analytes in plasma samples for a clinical study. Intra- and interday precision evaluated at three concentrations for the analytes were lower than 8.2 and 12.1%, respectively. Accuracy was in the range of 94.9–104.7%. The applicability of the developed method on human plasma samples illustrated the range 45.1–72.8, 98.4–128.3, 0.9–1.2, and 2.7–6.1 μg/L for tamoxifen, N-desmethyltamoxifen, 4-hydroxytamoxifen, and endoxifen, respectively. The validated method can be effective for the pharmacokinetics, pharmacodynamics, and therapeutic drug monitoring studies of tamoxifen and its main metabolites in biological fluids.     

Preparation and electrochemical performances of nanoporous/cracked cobalt oxide layer for supercapacitors

Nanoporous/cracked structures of cobalt oxide (Co₃O₄) electrodes were successfully fabricated by electroplating of zinc–cobalt onto previously formed TiO₂ nanotubes by anodizing of titanium, leaching of zinc in a concentrated alkaline solution and followed by drying and annealing at 400 °C. The structure and morphology of the obtained Co₃O₄ electrodes were characterized by X-ray diffraction, EDX analysis and scanning electron microscopy. The results showed that the obtained Co₃O₄ electrodes were composed of the nanoporous/cracked structures with an average pore size of about 100 nm. The electrochemical capacitive behaviors of the nanoporous Co₃O₄ electrodes were investigated by cyclic voltammetry, galvanostatic charge–discharge studies and electrochemical impedance spectroscopy in 1 M NaOH solution. The electrochemical data demonstrated that the electrodes display good capacitive behavior with a specific capacitance of 430 F g^?1 at a current density of 1.0 A g^?1 and specific capacitance retention of ca. 80 % after 10 days of being used in electrochemical experiments, indicating to be promising electroactive materials for supercapacitors. Furthermore, in comparison with electrodes prepared by simple cathodic deposition of cobalt onto TiO₂ nanotubes(without dealloying procedure), the impedance studies showed improved performances likely due to nanoporous/cracked structures of electrodes fabricated by dealloying of zinc, which provide fast ion and electron transfer routes and large reaction surface area with the ensued fast reaction kinetics.     

Bending of Euler–Bernoulli nanobeams based on the strain-driven and stress-driven nonlocal integral models: a numerical approach

Eringen’s nonlocal elasticity theory is extensively employed for the analysis of nanostructures because it is able to capture nanoscale effects. Previous studies have revealed that using the differential form of the strain-driven version of this theory leads to paradoxical results in some cases, such as bending analysis of cantilevers, and recourse must be made to the integral version. In this article, a novel numerical approach is developed for the bending analysis of Euler–Bernoulli nanobeams in the context of strain- and stress-driven integral nonlocal models. This numerical approach is proposed for the direct solution to bypass the difficulties related to converting the integral governing equation into a differential equation. First, the governing equation is derived based on both strain-driven and stress-driven nonlocal models by means of the minimum total potential energy. Also, in each case, the governing equation is obtained in both strong and weak forms. To solve numerically the derived equations, matrix differential and integral operators are constructed based upon the finite difference technique and trapezoidal integration rule. It is shown that the proposed numerical approach can be efficiently applied to the strain-driven nonlocal model with the aim of resolving the mentioned paradoxes. Also, it is able to solve the problem based on the strain-driven model without inconsistencies of the application of this model that are reported in the literature.