Graded PZT ceramics for piezoelectric transformers

In the present study two types of the synthesized Pb(Zr_1−xTi_x)O₃ (PZT) powders differing in Zr/Ti ratio were used to prepare the spatially inhomogeneous (i.e., graded) structure. A position-dependent chemical composition was expected to cause the property gradient. Disk-shaped compacts were prepared in a way such that two different orientations of the radial gradients were formed. The solid state sintering under pressure was utilized to prepare ceramics. Simultaneous thermal analysis was used to study thermal behavior of the ceramic powders. Graded PZT ceramics were characterized using X-ray diffraction, scanning electron microscopy and energy dispersive spectroscopy. It was also characterized in terms of its dielectric properties by both bridge technique and the impedance spectroscopy. On the basis of graded PZT ceramics the disk-shaped radial mode piezoelectric transformer was developed and fabricated.     

Cathode etching rate in abnormal glow discharges

The cathode etching rate in an abnormal glow discharge was calculated taking into account sputtering both by ions and energetic neutrals originating in cathode dark space due to the charge exchange collisions. The advantage of the model proposed is the evaluation of energetic neutral scattering by the sputtering gas.     

Ion energies at the cathode of the DC planar magnetron sputtering discharge

The energy distribution of the ions striking the cathode of the dc planar magnetron system was measured over a range of the typical sputtering conditions (magnetic field of 0.07–0.13 T, argon pressure of 0.01–10 Pa, discharge voltage of 250–600 V). The results obtained allow us to conclude that the major part of the incident ion flux originates in the cathode fall region. The theoretical model developed in terms of mobility theory makes it possible to evaluate the cathode fall voltage and its dependence on the sputtering conditions. It was found that the normalized integral form of the incident ions, energy spectrum is practically independent of the sputtering discharge parameters.     

Classification of genomic data: some aspects of feature selection

Feature selection, while working with genomic data sets, is of particular interest, not only for classification (diagnostics) improvement, but also for the data interpretability. Application of the multivariate feature selection approaches allows an efficient reduction of data dimensionality, but as demonstrated in our study, sets of the selected variables depend on the objective function of the classifier. It is possible to select different subset of genes for classification due to the correlation of genes but their interpretation ought to be cautiously made.     

Determination of gliclazide in pharmaceutical preparations by capillary gas chromatography with cool on-column injection and elimination of the matrix effect.

Conditions were established for the identification and quantitation of gliclazide in pharmaceutical preparations by capillary gas chromatography with flame ionization detection and cool on-column injection. Gliclazide was extracted with methanol and, after filtration, assayed on a (25 m x 0.25 mm id, 0.2 microm film thickness) CP-WAX 58 (FFAP)-CB WCOT fused silica column. Because the available preparations were of various origins and, therefore, could differ in auxiliary substances and their qualitative parameters, the influence of the matrix constituents on the analytical results was taken into account. Good separation conditions were established for the developed method. The retention time of gliclazide is about 36 min and differs from the retention times of the internal standard (approximately 29 min) and additional peaks present in chromatograms (20-26 min), which were assigned to matrix constituents. The recoveries of gliclozide were high and reached 96.5%. The developed method is characterized by selectivity and precision (relative standard deviation 0.38-1.26%), a wide range of linearity (0.1-10.0 mg/mL), and a limit of detection of 30 ng. In addition, the results of chromatographic analyses calculated in 3 ways were compared with those obtained by UV spectrophotometry. The suggested technique of cool on-column injection, in contrast with split-splitless injection (used in preliminary investigations), reduces to a minimum the possibility of thermal decomposition of gliclazide.     

Hyperfine interactions in some Aurivillius Bim+1Ti3Fem−3O3m+3 compounds

X-ray diffraction and Mössbauer spectroscopy were applied as complementary methods to investigate the structure and hyperfine interactions in the series of Bi_m+1Ti₃Fe_m−3O_3m+3 Aurivillius compounds with m=4, 6, 7 and 8. Samples were synthesized by the solid-state sintering method at various temperatures. As X-ray diffraction analysis proved, the compounds formed single phases at temperature above 993 K. Mössbauer studies have confirmed diffraction measurements. Compounds synthesized at 993 K contained residual hematite, however these sintered at elevated temperatures were single-phased materials. Room-temperature Mössbauer spectra of Bi_m+1Ti₃Fe_m−3O_3m+3 compounds revealed their paramagnetic properties, what is consistent with the literature data concerning the Néel temperature of these ceramics (T_N is smaller than room temperature). Detailed analysis of MS spectra allowed to state that iron ions may occupy both tetrahedral and octahedral sites in the crystallographic lattice of Aurivillius compounds.     

Theoretical Studies on the Mechanism of deNOx Process in Cu–Zn Bimetallic System—Comparison of FAU and MFI Zeolites

In the present study we propose a more promising catalyst for the deNOx process to eliminate harmful nitrogen oxides from the environment. The study was performed with a computer calculation using density functional theory (DFT) based on an ab initio method. Two zeolite catalysts, FAU and MFI, were selected with additional Cu–O–Zn bimetallic dimer adsorbed inside the pores of both zeolites. Based on the analysis of preliminary studies, the most probable way of co-adsorption of nitric oxide and ammonia was selected, which became the initial configuration for the reaction mechanism. Two types of mechanisms were proposed: with hydroxyl groups on a bridged position of the dimer or a hydroxyl group on one of the metal atoms of the dimer. Based on the results, it was determined that the FAU zeolite with a bimetallic dimer and an OH group on the zinc atom was the most efficient configuration with a relatively low energy barrier. The real advantage of the Cu–Zn system over FAU and MFI in hydrothermal conditions has been demonstrated in comparison to a conventional Cu–Cu catalyst.     

Cobalt antidot arrays on membranes: Fabrication and investigation with transmission X-ray microscopy

We have developed a method to fabricate ferromagnetic antidot arrays on silicon nitride membrane substrates for electron or soft X-ray microscopy with antidot periods ranging from 2 μm down to 200 nm. Observations of cobalt antidot arrays with magnetic soft X-ray microscopy show that for large periods, flux closure states occur between the antidots in the as-grown state and on application of a magnetic field, domain chains are created which show a spin configuration at the chain ends comprising four 90° walls. Pinning of the domain chain ends plays an important role in the magnetization reversal, determining the length of the chains and resulting in preservation of the domain chain configuration on reducing of the applied magnetic field to zero.     

Thermal behavior of BST//PVDF ceramic–polymer composites

In this paper, we report the results of a study of microstructure and thermal behavior of ceramic–polymer composites composed of barium strontium titanate Ba_0.6Sr_0.4TiO₃ (BST60/40) and polyvinylidene fluoride (PVDF). The Ba_0.6Sr_0.4TiO₃ ceramic powder was prepared by the sol–gel method. Thermal evolution of the dried gel as well as ceramic powder was studied by simultaneous thermal analysis. The composite BST60/40//PVDF was obtained by hot pressing method for volume fraction of BST60/40 ceramic powder c _v = 50 %. The morphology of BST60/40//PVDF composite powder was observed by transmission electron microscopy and the morphology of BST60/40//PVDF composite sample was observed by scanning electron microscopy. Temperature dependence of dielectric constant and dielectric loss factor of BST60/40//PVDF composites was measured in the frequency range of f = (10 × 10³–1 × 10⁶) Hz. Dynamic mechanical properties of BST60/40//PVDF composites were measured by dynamic mechanical thermal analysis DMTA.