Nanocomposite hydrogel consisting of Na‐montmorillonite with enhanced mechanical properties

A new kind of nanocomposite (NC) hydrogel with Na‐montmorillonite (MMT) is presented in this article. The NC hydrogels were synthesized by free radical copolymerization of acrylamide and (3‐acrylamidopropyl) trimethylammonium chloride (ATC) in the presence of MMT and N,N′‐methylene‐bis‐acrylamide used as chemical cross‐linker. Due to the cation‐exchange reaction between MMT and ATC (cationic monomer) during the synthesis of NC hydrogels, MMT platelets were considered chemical “plane” cross‐linkers, different from “point” cross‐linkers. With increasing amount of MMT, the crosslinking degree enhanced, causing a decrease of the swelling degree at equilibrium. Investigations of mechanical properties indicated that NC hydrogels exhibited enhanced strength and toughness, which resulted from chemical interaction between exfoliated MMT platelets and polymer chains in hydrogels. Dynamic shear measurements showed that both storage modulus and loss modulus increased with increasing MMT content. The idea described here provided a new route to prepare hydrogels with high mechanical properties by using alternative natural Na‐MMT. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 1020–1026     

Lipase‐Supported Metal–Organic Framework Bioreactor Catalyzes Warfarin Synthesis

A green and sustainable strategy synthesizes clinical medicine warfarin anticoagulant by using lipase‐supported metal–organic framework (MOF) bioreactors (see scheme). These findings may be beneficial for future studies in the industrial production of chemical, pharmaceutical, and agrochemical precursors.     

Measured and Predicted Solubility Phase Diagrams of Quaternary Systems LiBr-NaBr-MgBr2-H2O and LiBr-KBr-MgBr2-H2O at 298.15 K

The stable phase equilibria of quaternary systems LiBr-NaBr-MgBr₂-H₂O and LiBr-KBr-MgBr₂-H₂O at 298.15 K were studied by both experimental measurement(isothermal solution saturation method) and theoretical prediction(Pitzer model). The solubilities of the saturated solution have been determined experimentally and two stable phase diagrams and relevant water diagrams of the two quaternary systems were obtained. Results show that quaternary system LiBr-NaBr-MgBr₂-H₂O is hydrate II type as NaBr and NaBr·2H₂O coexistence. Its phase diagram consists of only one invariant point, four univariant curves, and five crystallization fields. The quaternary system LiBr-KBr-MgBr₂-H₂O is a complex type as the double salt KBr·MgBr₂·6H₂O formed. In addition to this double salt, the three single salts LiBr·2H₂O, KBr and MgBr₂·6H₂O also crystallize. In this paper, the solubilities of phase equilibria in above quaternary systems were also calculated by the Pitzer's electrolyte solution model. All the needed parameters can be obtained from the literature or be fitted by experimental data. On the Basis of the experimental and calculated results, the phase diagram of the quaternary system was plotted for comparison. It shows that the calculation results are consistent with the experimental ones.     

从诺贝尔物理学奖看光学的发展

从一个新的角度分析、讨论了光学的发展过程.并对光学今后的发展做了展望.     

生长温度对碳纳米管阴极场发射性能的影响

碳纳米管(Carbon Nanotubes,CNTs)场发射平面显示器(Field Emission Display,FED)与其他显示器比较显示了其独特优点,被认为是未来理想的平面显示器之一。碳纳米管阴极作为器件的核心部分,其性能的好坏直接影响显示器的性能。针对30~60英寸(76.2~152.4cm)大屏幕显示器所用的厚膜工艺,即采用丝网印刷法制备了碳纳米管阴极阵列,研究了化学气相沉积法在不同温度下生长的CNTs的场发射电流-电压特性,找到了适合FED用碳纳米管的最佳生长温度。结果表明生长温度越高(750℃),CNTs场发射性能越好。并用荧光粉阳极测试这些CNTs的场发射发光显示效果,验证了上述结论。     

改进型磁绝缘线振荡器的设计和数值模拟

 综合两种现有磁绝缘线振荡器的优点，对器件进行改进，将双渐变结构、轭流片和阻抗渐变三种增大功率的机制综合考虑，利用二维半全电磁PIC程序进行数值模拟，设计了一种新的改进型磁绝缘线振荡器，当外加电压为550kV，电流为35kA左右时，在L波段获得了6GW的峰值输出功率。     

辐射传递蒙特卡洛法精度分析及数值试验

本文建立了蒙特卡洛法模拟散射参与性介质内辐射传递计算模型。对蒙特卡洛法的计算精度及运行时间进行了较为详细的分析,提出了几种判断计算精度的方法。同时,借助蒙特卡洛法模拟辐射传递过程,进行数值“辐射实验”。利用该“实验结果”进行了物性反问题研究。在已知光学厚度的前提下,得到散射反照率与后半球辐射热流之间的单值函数关系。     

半导体激光器发射光谱实验仪

设计了一种半导体激光器发射光谱实验仪 ,可以用来观测LD发射的荧光光谱、激光光谱 ,以及了解光栅外腔选取单纵模、压窄线宽、波长调谐的机理 .该实验仪结构紧凑 ,物理概念清晰 ,适用于大专院校的光学实验教学     

基于图像处理技术的束流剖面监视系统

 介绍了在兰州重离子加速器上利用荧光靶图像获取装置测量并计算束流剖面参数的方法，并建立了图像获取、处理、束流参数计算的实时测量软件系统。该系统具有可靠性好、测量直观、界面友好等优点。