排序方式: 共有33条查询结果,搜索用时 15 毫秒
1.
2.
3.
包钴型γ-Fe2O3磁粉分为包钴γ-Fe2O3(简记为Co-γ-Fe2O3)和包钴包亚铁γ-Fe2O3(简记为CoFe-γ-Fe2O3)两种,它们的矫顽力可比γ-Fe2O3磁粉的提高100至400Oe左右,本工作对这两种磁粉矫顽力增大的原因作了探讨,认为它们矫顽力增大的机制不同:CO-γ-Fe2O3矫顽力增大是由于表面包覆一层Co(OH)2使表面各向异性增大,而CoFe-γ-Fe2O3则是由于表面包覆的是钴铁氧体,γ-Fe2O3与钴铁氧体之间发生耦合作用,使矫顽力增大。 相似文献
4.
IntroductionRecently ,wehavereportedthecoordinationchem istryof 1,2 naphthoquinone mono oxime (nqoH)towardsplatinumgroupmetalsincludingrutheniumandrhodi um .1 8ThereactionsofnqoHwithrutheniumcarbonyl[Ru3(CO) 12 ]leadtofiveisomersofmononuclearrutheni umcarbonylcomplexesof 1,2 naphthoquinone mono oxime .1 3Thepresenceoftheliablecarbonylligandsofferstheopportunitytointroduceavarietyofligandswithspe cificfunctionalgroupsintothemolecule .3Bythisstrategy ,metal containingpolymers ,supramolecular… 相似文献
5.
6.
包钴铁氧体型,γ-Fe_2O_3磁粉(简记为CoFe-γ-Fe_2O_3)是针状γ-Fe_2O_3磁粉与Co~( )和Fe~( )溶液起反应,在每个针状颗粒上包覆了一层钴铁氧体固溶体。经此种方法处理后的γ-Fe_2O_3磁粉的矫顽力及其它磁特性有较大的提高。如矫顽力由原来415Oe增加到715Oe;剩磁和矫顽力随时间及温度变化小等。我们利用穆斯堡尔效应并配合其它研究手段进行了研究,认为:CoFe-γ-Fe_2O_3磁粉矫顽力的提高,主要是由于γ-Fe_2O_3磁粉表面包覆了一层钴铁氧体固溶体,γ-Fe_2O_3与钴铁氧体固溶体之间发生磁耦合作用之故。 相似文献
7.
8.
Gold 3D cylindrical nanoelectrode ensembles (NEEs), 100 nm in diameter and 500 nm in length were prepared by electroless template synthesis in polycarbonate filter membranes, followed by selective controlled chemical etching. The morphology of the nanowires and cylindrical NEEs was imaged by scanning electron microscopy. The protruding nanoelectrodes were in good parallel order. EDX study showed that the nanoelectrode elements consisted of pure gold. The electrochemical evaluation of the 3D electrodes was conducted using the well known [Fe(CN)6]^3-/[Fe(CN)6]^4- couple. Cyclic voltammgrams (CV) show a very low double layer charging current and a higher ratio of signal to background current than 2D disc NEEs. Electrochemical impedance spectroscopy (EIS) indicates that the 3D cylindrical NEEs effectively accelerate the charge transfer process, which is in consistent with the results of CV. The linear relationship with a slope of 0.5 between lg Ipc and lg v shows that linear diffusion is dominant on the 3D cylindrical NEEs at conventional scan rates. 相似文献
9.
加压烧结是一种新工艺.目前,工业和实验室采用的压力因受模具抗张强度的限制,大约是200公斤/厘米2左右.进一步提高压力有助于降低烧结温度,缩短烧结时间,获得接近理论密度的烧结体.菲利浦公司建立过一种连续热压装置,压力可达1000公斤/厘米2,它是靠六个油缸支持一个六棱柱形的氧化铝模筒承受高医,虽然设备比较复杂,但由于具有压力高及连续烧结的特点,受到了高压研究工作者的重视. 我们采用叶腊石受热膨胀产生的支撑力,使高温氧化铝陶瓷模筒可在1200℃承受2000公斤/厘米2的压力,并以可移动的上、下压杆实现连续加压烧结. 模具结构如图1所示.… 相似文献
10.
IntroductionIn traditional optimum structural math model,the target function and the constraintfunction are all considered as the certain value.But it does not accord to the actual forcedenvironment condition and structural status.Thus the optimum results… 相似文献