On Necessary Optimality Conditions with Higher-Order Complementarity Slackness for Set-Valued Optimization Problems

Set-Valued and Variational Analysis - We aim to establish Karush-Kuhn-Tucker multiplier rules involving higher-order complementarity slackness under Hölder metric subregularity. These rules...     

Polymer nanoparticles with a sensitive CO2‐responsive hydrophilic/hydrophobic surface

Poly(methyl methacrylate) (PMMA) nanoparticles with a sensitive CO₂‐responsive hydrophilic/hydrophobic surface that confers controlled dispersion and aggregation in water were prepared by emulsion polymerization at 50 °C under CO₂ bubbling using amphiphilic diblock copolymers of 2‐dimethylaminoethyl methacrylate (DMAEMA) and N‐isopropyl acrylamide (NIPAAm) as an emulsifier. The amphiphilicity of the hydrophobic–hydrophilic diblock copolymer at 50 °C was triggered by CO₂ bubbling in water and enabled the copolymer to serve as an emulsifier. The resulting PMMA nanoparticles were spherical, approximately 100 nm in diameter and exhibited sensitive CO₂/N₂‐responsive dispersion/aggregation in water. Using copolymers with a longer PNIPAAm block length as an emulsifier resulted in smaller particles. A higher concentration of copolymer emulsifier led to particles with a stickier surface. Given its simple preparation and reversible CO₂‐triggered amphiphilic behavior, this newly developed block copolymer emulsifier offers a highly efficient route toward the fabrication of sensitive CO₂‐stimuli responsive polymeric nanoparticle dispersions. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019, 57, 2149–2156     

A Hydroperoxide-Mediated Decarboxylation of α-Ketoacids Enables the Chemoselective Acylation of Amines

Strategies for the formation of amide bonds, that is, one of the most basic and important transformations in organic synthesis, have so far focused predominantly on dehydration reactions. Herein, we report and demonstrate the practical utility of a novel decarboxylative amidation of α-ketoacids by using inexpensive tert-butyl hydroperoxide (TBHP), which is characterized by high yields, a broad substrate scope, mild reaction conditions, and a unique chemoselectivity. These features enable the synthesis of peptides from amino acid derived α-ketoacids under preservation of the stereochemical information.     

一类函数方程的稳定性及微商配置解

本文对一类重要的函数方程建立解稳定性定理,提出微商配置解,证明了收敛性.     

3,7-二硝基亚氨基-2,4-二氮杂双环[3,3,0]辛烷的放热分解反应动力学

在程序升温条件下 ,用DSC研究了标题化合物的放热分解反应动力学 .用线性最小二乘法、迭代法以及二分法与最小二乘法相结合的方法 ,以积分方程、微分方程和放热速率方程拟合DSC数据 .在逻辑选择建立了微分和积分机理函数的最可几一般表达式后 ,用放热速率方程得到相应的表观活化能 (Ea)、指前因子 (A)和反应级数 (n)的值 .结果表明 :该反应的微分形式的经验动力学模式函数、Ea 和A值分别为 (1-α) 0 .44、2 30 .4kJ/mol和 10 18.16s-1.借助加热速率和所得动力学参数值 ,提出了标题化合物放热分解反应的动力学方程 .该化合物的热爆炸临界温度为 30 2 .6℃ .上述动力学参数对分析、评价标题化合物的稳定性和热变化规律十分有用 .     

一类非线性微分方程的脉冲镇定

针对一般形式的常微分系统提出了脉冲指数镇定的概念，具体研究了一类分离变量型非线性常微分方程的脉冲镇定问题，得到了该方程可脉冲指数镇定的充分判据，全文的概念及结论突出了脉冲在方程稳定性方面的控制效果。     

CNx纳米管的制备、结构观察及低场致电子发射性能研究

采用高温热解法，以乙二胺为前驱液，在沉积有铁催化剂的p型硅（111）基底上制备出了定向生长的CNx纳米管.利用扫描电子显微镜、高分辨率透射电子显微镜和拉曼光谱对CNx纳米管进行了形貌观察和表征.CNx纳米管的高度在20?μm左右，直径在50—100nm之间，具有明显的“竹节状”结构，结晶有序度较差.对CNx纳米管薄膜进行低场致发射性能测试：外加电场为1.4V/μm，观察到20?μA /cm2发射电流，外电场升至2.54V/μm时发射电流达到1.280mA/cm2，在较高外电场下，没有发现电流“饱和”.这比 关键词： CNx纳米管 高温热解 “竹节状”结构 场致发射     

Combined effects of clay modifications and compatibilizers on the formation and physical properties of melt‐mixed polypropylene/clay nanocomposites

The melt mixing technique was used to prepare various polypropylene (PP)‐based (nano)composites. Two commercial organoclays (denoted 20A and 30B) served as the fillers for the PP matrix, and two different maleated (so‐called) compatibilizers (denoted PP‐MA and SMA) were employed as the third component. The results from X‐ray diffraction (XRD) and transmission electron microscope (TEM) experiments revealed that 190 °C was an adequate temperature for preparing the nanocomposites. Nanocomposites were achieved only if specific pairs of organoclay and compatibilizer were simultaneously incorporated in the PP matrix. For example, PP/20A(5 wt %)/PP‐MA(10 wt %) and PP/30B(5 wt %)/SMA(5 wt %) composites exhibited nanoscaled dispersion of 20A or 30B in the PP matrix. Differential scanning calorimetry (DSC) results indicated that the organoclays served as nucleation agents for the PP matrix. Generally, their nucleation effectiveness increased with the addition of compatibilizers. The thermal stability enhancement of PP after adding 20A was confirmed with thermogravimetric analysis (TGA). The enhancement became more evident as a suitable compatibilizer was further added. However, for the 30B‐included composites, thermal stability enhancement was not evident. The dynamic mechanical properties (i.e., storage modulus and loss modulus) of PP increased as the nanocomposites were formed; the properties increment corresponded to the organoclay dispersion status in the matrix. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 4139–4150, 2004