Fracture instability of notched cracked plates characterized by the strain energy density theory

The fracture instability of a mechanical system is analyzed by the strain energy density theory. The local relative minima of the strain energy density function dW/dV referred to local coordinate systems at each point of the body are distinguished from the global minimum of dW/dV, G, which is referred to a fixed global coordinate system. Failure by fracture starts from the maximum of the local minima of dW/dV, L, and passes from point G. The distance l between L and G along the fracture trajectory is introduced as a length parameter to characterized the fracture instability of the system. Numerical results are obtained and discussed for a cracked plate with two symmetrical notches subjected to a monotonically rising tensile stress perpendicular to the crack axis.     

Growth of an arc-crack in bonded dissimilar materials

The problem of growth of a crack lying along the interface of a circular inclusion embedded in an infinite plate is studied within the framework of linear elasticity. The plate is subjected to a uniform uniaxial stress at infinity at any angle of inclination relatively to the crack. The critical load for unstable crack growth, the angle of initial crack extension and the subsequent crack path are investigated using the strain energy density fracture criterion. The combined effect of crack length and orientation on the fracture stress is considered for the case of an aluminum-epoxy composite.     

Stable growth of a central crack

The elastic fracture behavior of a plate subjected to uniform stress surrounding two equal cracks inclined at an angle is investigated. The orientation of the crack plane with applied stress can be varied. Among the cases are: (1) two cracks inclined symmetrically with respect to the vertical and horizontal applied stress, and (2) one crack is horizontal while the other is inclined to the vertical applied stress. The strain energy density criterion is used for determining the combined crack and load arrangement that correspond to the lowest critical load at global instability. The direction of crack initiation is also determined. Quantitative results pertaining to the fracture characteristics are given in graphical forms.     

Investigation of shrinkage-induced stresses in stereolithography photo-curable resins

An experimental study has been undertaken to investigate the shrinkage characteristics of acrylic-based and epoxy-based stereolithography (SL) photopolymer resin systems after they have been laser cured and post-cured under ultraviolet (UV), and thermal exposure. The induced residual stresses and strains were determined by the shadow moiré and the hole-drilling strain-gage methods. Out-of-plane displacements (warpage) of acrylic-based post-cured resin plates were recorded by means of the shadow moiré method and correlated to the shrinkage strains by theoretical analysis. The induced residual stresses in the epoxy-based cylindrical resin specimens were determined from strains of three-element strain-gage rosettes of the blind-hole drilling method. Results are presented for the shrinkage stresses and strains for both material systems as a function of the post-curing process (UV, thermal). It was found that the shrinkage strains in the acrylic-based photopolymer resin were of considerable magnitude, while thermal post-curing resulted in higher shrinkage stresses for both material systems. The values of the shrinkage stresses compare well with those of the existing literature.     

Processing and characterization of epoxy/clay nanocomposites

Nanocomposite materials consisting of an epoxy matrix and silicate clay particles have been processed and characterized mechanically. The clay material used was a modified natural montmorillonite. The clay particles consisted of 1 nm thick layers with aspect ratios in the range of 100–1000. The clay particles were mixed with acetone and sonicated, then mixed with the polymer, deaerated and cured. The ultimate objective of processing was to produce a polymer/clay nanocomposite with separated (exfoliated) platelets, dispersed as uniformly as possible. Samples were prepared with clay concentrations of up to 10 wt%. The process used resulted in limited exfoliation but mostly intercalation, i.e., infusion of polymer between the silicate layers and increase of interlayer spacing. The characteristics of the nanocomposite were assessed by transmission electron microscopy and x-ray diffraction. Results from these observations show that the basal spacing of clay platelets increased from an initial pre-processing value of 1.85 nm to 4.5 nm. Enhancement of mechanical properties was measured by tensile testing of coupons. Stiffness increases of up to 50% over that of the unfilled epoxy were measured for clay concentrations of 5 wt%. Strength increases were also measured for low clay concentrations and low strain rate loading. Micromechanics modeling of mechanical behavior is discussed as a function of clay platelet dispersion.     

Failure instability of a debonded interface in the presence of a main crack

The problem of fracture initiating from an edge crack in a nonhomogeneous beam made of two dissimilar linear elastic materials that are partially bonded along a common interface is studied by the strain energy density theory. The beam is subjected to three-point bending and the unbonded part of the interface is symmetrically located with regard to the applied loading. The applied load acts on the stiffer material, while the edge crack lies in the softer material. Fracture initiation from the tip of the edge crack and global instability of the composite beam are studied by considering both the local and global stationary values of the strain energy density function, dW/dV. A length parameter l defined by the relative distance between the maximum of the local and global minima of dW/dV is determined for evaluating the stability of failure initiation by fracture. Predictions on critical loads for fracture initiation from the tip of the edge crack, crack trajectories and fracture instability are made. In the analysis the load, the length of the edge crack and the length and position of the interfacial crack remained unchanged. The influence of the ratio of the moduli of elasticity of the two materials, the position of the edge crack and the width of the stiffer material on the local and global instability of the beam was examined. A general trend is that the critical load for crack initiation and fracture instability is enhanced as the width and the modulus of elasticity of the stiffer material increase. Thus, the stiffer material acts as a barrier in load transfer.     

A damage model for crack initiation and growth

A damage accumulation model is presented for the study of the problem of crack initiation and stable growth in an elastic-plastic material. A centre-cracked specimen subjected to a uniform stress perpendicular to the crack plane is considered. A coupled stress and failure analysis is performed by using a finite element computer program based on J₂-plasticity theory in conjunction with the strain energy density theory. After initial yielding, each material element follows a different equivalent uniaxial stress-strain behavior depending on the amount of energy dissipation by permanent deformation. A host of uniaxial stress-strain curves constituting parts of the same stress-strain curve were assigned to material elements for each increment of loading. The path-dependent nature of the onset of crack initiation and growth was revealed. The proposed model predicts faster crack growth rates than those obtained on the basis of a single uniaxial stress-strain curve and is closer to experimental observation.     

Thin and Thermally Stable Periodic Metastructures

We design, fabricate, and test thin thermally stable metastructures consisting of bi-metallic unit cells and show how the coefficient of thermal expansion (CTE) of these metastructures can be finely and coarsely tuned by varying the CTE of the constituent materials and the unit cell geometry. Planar and three-dimensional finite element method modeling (FEM) is used to drive our design and inform experiments, and predict the response of these metastructures. We develop a robust experimental fabrication procedure in order to fabricate thermally stable samples with high aspect ratios. We use digital image correlation (DIC) and an infrared camera to experimentally measure displacement and temperature during testing and compute the CTE of our samples. The samples, composed of an aluminum core and an external titanium frame, exhibit a CTE of 2.6 ppm/°C, which is significantly lower than either constituent. These unit cells can be assembled over a large area to create thin low-CTE foils. Finally, we demonstrate how the approach developed in this work can be used to fabricate metastructures with CTE’s ranging from ?3.6 ppm/°C to 8.4 ppm/°C.