Preparation of 3-substituted and 2,3-disubstituted-4,4,4-trifluoro-2-butenoic acids—Perkin condensation of activated aromatic ketones

The Perkin reaction of the activated aromatic ketones (2,2,2-trifluoroacetophenone and its 4′-phenyl-derivative) with various condensing agents (acetic anhydride, propionic anhydride, phenylacetic acid/acetic anhydride) gives the title compounds in good or moderate yields, and high E-stereoselectivity. For some derivatives an appreciable amount of the Z isomer was also formed. Several of the resulting butenoic acids and their methyl esters are synthesised and characterised for the first time.     

Atomic distributions in acetylene-air flame using hydraulic high-pressure nebulization with direct (100%) introduction of solutions Applications to speciation analysis

One of the fundamental factors of the performance of atomic spectrometric methods is the efficiency of sample introduction into flame or plasma. By utilization of the formerly developed hydraulic high-pressure nebulizer, a nebulizer/burner system with solution uptake efficiency of 100% have been worked out. Optimizing operation parameters of nebulizer/burner system, an improvement of 2-12 times was achieved for the signal-to-noise ratio in the flame emission and flame atomic absorption spectrometry, depending on sample flow rate. This nebulizer is especially suitable for development of liquid chromatography-AAS/FES coupled technique for speciation analytical tasks.     

Study of the gas-phase parameters affecting the silicon-oxide film deposition induced by an ArF laser

A study of the gas-phase parameters involved in ArF laser induced chemical vapour deposition of silicon-oxide thin films is presented. A complete set of experiments has been performed showing the influence of the concentration of the precursor gases, N₂O and SiH₄, and their influence on total and partial pressures on film growth and properties. In this paper we demonstrate the ability of this LCVD method to deposit silicon oxide films of different compositions and densities by appropriate control of gas composition and total pressure. Moreover, a material specific calibration plot comprising data obtained using different preparation techniques is presented, allowing determination of the stoichiometry of SiO _x films by using FTIR spectroscopy independently of the deposition method. For the range of processing conditions examined, the experimental results suggest that chemical processes governing deposition take place mainly in the gas phase.     

Singular terms of helicity amplitudes at one loop in QCD and the soft limit of the cross sections of multi-parton processes

We describe a general method that enables us to obtain all the singular terms of helicity amplitudes of n-parton processes at one loop. The algorithm uses helicity amplitudes at tree level and simple color algebra. We illustrate the method by calculating the singular part of the one-loop helicity amplitudes of all 2 → 3 parton subprocesses. The results are used to derive the soft gluon limit of the cross sections of all 2 → 4 parton scattering subprocesses which provide a useful initial condition for the angular ordering approximation to coherent multiple soft gluon emission, incorporated in existing Monte Carlo simulation programs.     

Property improvement of pulsed laser deposited boron carbide films by pulse shortening

Growth characteristics and surface morphology of boron carbide films fabricated by ablating a B₄C target in high vacuum with a traditional KrF excimer laser and a high brightness hybrid dye/excimer laser system emitting at the same wavelength while delivering 700 fs pulses are compared. The ultrashort pulse processing is highly effective. Energy densities between 0.25 and 2 J cm⁻² result in apparent growth rates ranging from 0.017 to 0.085 nm/pulse. Ablation with nanosecond pulses of one order of magnitude higher energy densities yields smaller growth rates, the figures increase from 0.002 to 0.016 nm/pulse within the 2-14.3 J cm⁻² fluence window. 2D thickness maps derived from variable angle spectroscopic ellipsometry reveal that, when ablating with sub-ps pulses, the spot size rather than the energy density determines both the deposition rate and the angular distribution of film material. Pulse shortening leads to significant improvement in surface morphology, as well. While droplets with number densities ranging from 1 × 10⁴ to 7 × 10⁴ mm⁻² deteriorate the surface of the films deposited by the KrF excimer laser, sub-ps pulses produce practically droplet-free films. The absence of droplets has also a beneficial effect on the stoichiometry and homogeneity of the films fabricated by ultrashort pulses.     

The phase composition of tin-nickel electrodeposited alloys

It was studied the tin phase composition of the electrodeposited alloys produced at different temperatures and current densities from an acid chloride/fluoride electrolyte and an acid chloride bath. Mössbauer spectra were consistent with a Ni₃Sn₄ intermetallic compound, dissolved tin, and a Cu?Sn intermetallic compound formed at the interface of the copper substrate.     

Adsorption of cyclic hydrocarbons on Pt and the interaction of the adsorbed species with hydrogen

The adsorption of six-membered hydrocarbon cycles and cyclopentane and the interaction of hydrogen with the adsorbed layer on polycrystalline Pt-foil have been studied. The work function change (Δφ) was followed by a Kelvin probe and the C/Pt peak ratio was determined by Auger electron spectroscopy. Combining these two techniques made it possible to distinguish between chemisorption via σ-bonds and π-complex formation. Benzene and toluene adsorbed first as π-complex while cyclohexane showed initially a partial aromatization and a π-complex-like bonding to the surface. Excess hydrocarbon or addition of hydrogen transformed the π-complex into σ-bonded species. Cyclopentane adsorbed via σ-bonds and showed no significant hydrogen effect.     

Pattern forming precipitation in gels due to coupling of chemical reactions with diffusion

Precipitate-forming chemical reactions have been studied in chemically cross-linked poly(vinyl alcohol) gel medium. One of the reactive components was incorporated into the gel, the other was allowed to diffuse into it. Depending on the experimental conditions the reaction-diffusion process often results in patterns of different type. Experiments performed in tubes and in thin layers were carried out in order to investigate the effects of various factors (cross-linking density, swelling degree as well as the concentrations of the outer and inner electrolytes) on the morphologies of the precipitate patterns. It was found that precipitation occurs not only in the Liesegang bands, but also between bands. Beside Liesegang-type structures, tree-like patterns have been observed, showing a characteristic periodicity in the density profile obtained by digitalized image analyses.     

Maskierung mit Kaliumjodid bei direkten Titrationen von Kupfer(II) mit Äthylendiamintetraessigsäure

Zusammenfassung Die Jodidoxydation durch Cu(II) wird in Anwesenheit von Ammoniak, Natriumtartrat, citrat oder -oxalat infolge Komplexbildung verhindert. Daher kann man z. B. Quecksüber(II) in Anwesenheit der genannten Komplexbildner mit Kaliumjodid maskieren und Kupfer(II) durch direkte Titration mit ÄDTA gegen Murexid, Brenzcatechinviolett, Chromazurol S, PAN oder PAR als Indikator bestimmen.

---

Masking with potassium iodide in direct titrations of copper(II) with ethylenediamine tetraacetic acid

Summary The formation of a complex prevents the iodide oxidation by Cu(II) in the presence of ammonia, sodium tartrate, citrate, or oxalate. Hence mercury(II) for instance, can be masked against potassium iodide in the presence of these complex formers, and Cu(II) can be determined by direct titration with EDTA in the presence of murexide, pyrocatechol violet, chromazurol, PAN or PAR as indicator.