Estimation of growth rate in unidirectionally solidified multicrystalline silicon by the growth-induced striation method

Multicrystalline silicon was grown by unidirectional solidification method using the accelerated crucible rotation technique. The application of the accelerated crucible rotation technique in unidirectional solidification method induced growth striations across the axial direction of the grown crystal. This striation pattern was observed from carbon concentration distribution, obtained by using Fourier transform infrared spectroscopy. The generated striation pattern was found to be weak and discontinuous. Some striations were absent, probably due to back melting, caused during each crucible rotation. From the growth striations and applied time period in crucible rotation, the growth rate was estimated by using Fourier transformation analysis.     

Integral Representations,Differentiability Properties and Limits at Infinity for Beppo Levi Functions

The first aim in the present paper is to give an integral representation for Beppo Levi functions on R ⁿ. Our integral representation is an extension of Sobolev's integral representation given for infinitely differentiable functions with compact support. As applications, continuity and differentiability properties of Beppo Levi functions are studied.Our second aim in this paper is to study the existence of limits at infinity for Beppo Levi functions. We also consider the existence of fine-type limits at infinity with respect to Bessel capacities, which yields the radial limit result at infinity.     

Complex impedance spectra of chip inductor using Li–Zn–Cu–Mn ferrite

A multi-layer chip inductor (MCI) was fabricated using polycrystalline Li–Zn–Cu–Mn ferrite and the green-sheet technique, and its complex impedance spectrum was evaluated with the help of numerical calculations. The complex impedance spectra of the MCI component using Ni–Zn–Cu ferrite, which have been widely used for this application, were very sensitive to the residual stress and deviated much from the calculated values; however, it was found that the complex impedance spectrum of the MCI component using Li–Zn–Cu–Mn ferrite is quite well reproduced by calculation, where the complex permittivity and permeability of the polycrystalline ferrite as well as the MCI dimensions, were used. It implied that the magneto-striction effect was negligible in case of MCI using Li–Zn–Cu–Mn ferrite, and that the difference was related to magneto-strictive coefficient of the polycrystalline ferrite. Consequently, utilization of Li–Zn–Cu–Mn ferrite enabled us to easily design the complex impedance of MCI component.     

Optical Glucose Monitoring Based on Femtosecond Two-Color Pulse Interferometry

We demonstrate the potential of femtosecond two-color pulse interferometry for in vitro optical glucose monitoring, by dispersion of the group refractive index in a glucose solution sample with respect to a red-color light and a blue-color light. By comparison with femtosecond one-color pulse interferometry, the basic performance of the present system with regard to sensitivity, quantitativeness, and tolerance to surrounding disturbances, is evaluated. The resulting accuracy and precision of glucose determination are 77 and 118mg/dl for 10-mm-sample-thickness, respectively. This near-common-path configuration of the two-color pulse light provides good stability to fluctuations of sample temperature, which is important in clinical applications. Considering the performance of femtosecond two-color pulse interferometry as an optical glucose sensor, a suitable measurement site for in vivo optical glucose monitoring is discussed.     

Hydrolysis of acetals in water under hydrothermal conditions

A simple method for the hydrolysis of acetals and ketals was accomplished in neutral water or aqueous media by hydrothermal treatment without using acidic reagents. The deacetalization reaction was effectively accelerated in the presence of calcium chloride. Because no acidic catalysts were employed, neutralization of the reaction mixture was not necessary after the reaction. This sequence was successfully applied to the hydrolysis of chitosan, a biodegradable polyaminosaccharide.     

Design of a widely tunable laser with a chirped ladder filter

We theoretically investigated a digitally tunable laser with a chirped ladder filter and a ring resonator to obtain a wide wavelength tuning range covering the whole C- or L- band. The clear relation between the tuning range and laser structure, especially the ladder filter, is described analytically. The introduction of a chirped structure into a ladder filter is effective in achieving both wide tunability and a stable lasing mode. A numerical simulation based on multimode rate equations shows that a tuning range of over 40 nm and a mode suppression ratio over 40 dB can be achieved by introducing a chirped ladder filter.     

OXIDATION OF RIBOSE MOIETY OF ADENOSINE INDUCED BY IRRADIATION OF NEAR-UV LIGHT IN THE PRESENCE OF IRON(III) CHLORIDE

Abstract— Irradiation of near-UV light in the presence of FeCl₃ caused oxidation of adenosine with concomitant reduction of Fe(III) under either aerobic or anaerobic atmosphere. Major photoproducts were adenine and adenosine-5'-aldehyde, showing that oxidation took place mostly at the ribose moiety of adenosine. Detailed study showed that the reaction proceeded by the light absorption due to Fe(III) at 300-350 nm.     

Fiber-in-Tube Solid Phase Extraction (FIT-SPE) for Miniaturized Sample Preparation Process

A typical analytical separation procedure has several important steps: sample preparation, isolation, identification, quantitation, statistical evaluation and final decision. Each step is alwayscritical to obtain correct results to fulfill the analytical purpose. In these various steps sample     

Reaction of indium ate complexes with allylic compounds. Controlling SN2/SN2′ selectivity by solvents

Vinyl and methylindium ate complexes (indates) were prepared and both the tendency of immigration and regioselectivity toward cinnamyl bromide were investigated. The vinyl group was more preferably transferred than the Me group, giving a regioisomeric mixture of S_N2 and S_N2′ products. The ratio of S_N2/S_N2′ selectivity can be controlled by solvents; in the presence of polar solvents, such as N-butylpyrrolidone (NBP) and THF, the S_N2′ product was mainly obtained, whereas the S_N2 product was selectively prepared in solutions containing hexane. The vinylindium compound, generated by the reaction of allylic-type diindium reagents with imine, was also converted to the corresponding vinyl indate, which was allowed to react with allyl chloride to give a three-component coupling product.