Non-destructive rapid analysis of brominated flame retardants in electrical and electronic equipment using Raman spectroscopy.

Using Raman spectroscopy without any preparation, we analyzed the brominated flame retardant, polybromodiphenyl ethers (PBDEs), which has been prohibited by the European Union. The typical Raman bands of PBDEs, which are clearly different from those of other brominated flame retardants, are from 100 to 300 cm(-1). In our analysis, the detection limit was about 100 ppm, and the analysis took about 1 min, whereas the usual method of solvent extraction using gas chromatography/mass spectroscopy takes 50 h.     

Novel UV‐induced photografting process for preparing poly(tetrafluoroethylene)‐based proton‐conducting membranes

A novel process comprising the UV‐induced photografting of styrene into poly(tetrafluoroethylene) (PTFE) films and subsequent sulfonation has been developed for preparing proton‐conducting membranes. Although under UV irradiation the initial radicals were mainly generated on the surface of the PTFE films by the action of photosensitizers such as xanthone and benzoyl peroxide, the graft chains were readily propagated into the PTFE films. The sulfonation of the grafted films was performed in a chlorosulfonic acid solution. Fourier transform infrared and scanning electron microscopy were used to characterize the grafted and sulfonated membranes. With a view to use in fuel cells, the proton conductivity, water uptake, and mechanical properties of the prepared membranes were measured. Even through the degree of grafting was lower than 10%, the proton conductivity in the thickness direction of the newly prepared membranes could reach a value similar to that of a Nafion membrane. In comparison with γ‐ray radiation grafting, UV‐induced photografting is very simple and safe and is less damaging to the membranes because significant degradation of the PTFE main chains can be avoided. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 2624–2637, 2007     

Preparation and certification of the new reference materials; plastics (disk form, JSAC 0621-0625) for determination of mercury using x-ray fluorescent analysis.

The Japan Society for Analytical Chemistry has developed some new plastic certified reference materials (CRMs) for the analysis of mercury in polyester disks using XRF analysis. These CRMs (named as JSAC 0621-0625) were prepared by casting polyesters including a toluene solution of organometallic compounds as a standard. Concentrations of the five levels of mercury ranged from 0 to 250 mg/kg. Homogeneity tests of prepared disks had shown excellent results. Interlaboratory comparison study for the certification was performed by 15 laboratory participants. The z-scores in robust statistical method was applied for the evaluation of outliers. The certified values were assigned after discarding outliers. The uncertainties of certified values were determined as the confidence levels of 95%.     

Electron spin resonance studies on radiation graft copolymerization in polyethylene. II. Grafting initiated by allyl radicals trapped in irradiated polyethylene

The regions trapping allyl radicals in irradiated polyethylene and the reactivity of the radicals with various monomers have been studied by electron spin resonance. Most of the allyl radicals are trapped in defects or surfaces of the crystallite, and only 10% of the radicals are trapped inside the crystallites. Since the reactivity of the allyl radicals depends on whether they come in contact with reactive monomers, the rate of reaction is related to the concentration of the monomers. When grafting reactions are initiated by allyl radicals, the rate of initiation is rapid and the rate of termination at the initial stage is also very fast. Consequently the yield of grafting increases at the initial stage but soon levels off, which is in contrast to the grafting behavior with alkyl radicals.     

Simplification and evaluation of a gold-deposited SPR optical fiber sensor.

The structure of the sensing element of a gold-deposited optical fiber sensor was simplified and quantitative analyses of various alcohols with the sensor showed improvement of the performance. The sensor uses surface plasmon resonance (SPR) at the interface of a sample solution and a thin (10 - 70 nm) gold film deposited on half of the exposed core of the optical fiber. The sensor with a film thickness of 45 nm can detect a small change of 5.6 x 10(-5) refractive index (RI) units in the refractivity. The response time is less than 0.5 min and the relative standard deviation for measurements is less than or equal to 1%. A straight line with a correlation coefficient of 0.9995 was obtained below 10%, v/v in the calibration curve for methanol solutions of benzyl alcohol. The minimum of the response curve due to the maximum excitation of SPR in the refractivity range from 1.33 to 1.44 RI units shifts to a lower refractivity as the film becomes thicker. The response curves of the sensors were calculated from SPR theoretical equations while considering of the distribution in the thickness of the deposited gold films. The improvement in the performance of the sensor is discussed.     

Vibrational frequencies and infrared absorption intensities of 1,2-dibromoethane

Infrared and Raman spectra of 1,2-dibromoethane CH₂BrCH₂Br and CD₂BrCD₂Br were observed in the liquid state, and the fundamental frequencies were determined by comparison with those of related molecules. Infrared absorption intensities of fundament bands were measured in the liquid state, and the intensity data were interpreted on the basis of the valence-optical theory. From the converged value of a population ratio, the energy difference between the trans and gauche isomers was determined, which was in good agreement with the value obtained from the temperature effect of the IR spectrum.     

Cyclopolycondensations

Fully aromatic polyquinazolinediones of high molecular weight were prepared by the cyclopolycondensation reaction of 4,4′-diamino-3,3′-biphenyldicarboxylic acid with aromatic diisocyanates. The poly(phosphoric acid) solution polymerization techniques yielded tractable poly(urea acid), which was converted to polyquinazolinediones by thermal cyclodehydration at 300–400°C. under reduced pressure. The polyquinazolinediones thus obtained have excellent thermal stability both in nitrogen and in air. The poly(urea acid) is soluble in dimethyl sulfoxide, and films can be cast from the polymer solution of poly(urea acid) (η_inh = 0.8 to 1.8). The films are made tough by being heated in nitrogen or under reduced pressure at 300–400°C. The polymerization mechanism of the cyclopolycondensation reaction was studied, and it was established that the polymerization proceeded through the formation of tractable poly(urea acid), Structure (I), of high molecular weight, followed by cyclodehydration, yielding poly(1,2-dihydro-2-imino-4H-3,1-benzoxazin-4-one), Structure (II). On subsequently being heated this undergoes intramolecular rearrangement along the polymer chain, giving the thermodynamically stable polyquinazolinedione, Structure (III).