Vacuum‐driven fluid manipulation by a piezoelectric diaphragm micropump for microfluidic droplet generation with a rapid system response time

Recently, we developed a convenient microfluidic droplet generation device based on vacuum‐driven fluid manipulation with a piezoelectric diaphragm micropump. In the present study built on our previous work, we investigate the influence of settings applied to the piezoelectric pump, such as peak‐to‐peak drive voltage (V_p‐p) and wave frequency, on droplet generation characteristics. Stepwise adjustments to the drive voltage in ±10‐V_p‐p increments over the range of 200?250 V_p‐p during droplet creation revealed that the droplet generation rate could be reproducibly controlled at a specific drive voltage. The droplet generation rate switched within <0.5 s after the input of a new voltage. Although the droplet generation rate depended on the drive voltage, this setting had almost no influence on droplet size. The frequency over the selected range (50?60 Hz) did not markedly influence the droplet generation rate or droplet size. We show that the current fluid manipulation system can be conveniently used for both droplet generation and for rapid droplet reading, which is required in many microfluidic‐based applications.     

Microwave‐assisted polycondensation of 4‐octylaniline with dibromoarylene

The Pd‐catalyzed polycondensation of 4‐octylaniline with various dibromoarylenes was carried out under microwave heating. Microwave heating led to a decrease in the reaction time and an increase in the molecular weight of the polymers as compared to conventional heating. Microwave heating also allowed the catalyst loading to be reduced to 1 mol %, yielding polymerization results that were comparable to those under conventional heating and 5 mol % catalyst. Investigations regarding field‐effect transistors and organic photovoltaic cells using the obtained poly(arylamine) with azobenzene units revealed that increasing the molecular weight of the polymer led to improved device performance, including hole mobility and power conversion efficiency. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 536–542     

A Hydroperoxide-Mediated Decarboxylation of α-Ketoacids Enables the Chemoselective Acylation of Amines

Strategies for the formation of amide bonds, that is, one of the most basic and important transformations in organic synthesis, have so far focused predominantly on dehydration reactions. Herein, we report and demonstrate the practical utility of a novel decarboxylative amidation of α-ketoacids by using inexpensive tert-butyl hydroperoxide (TBHP), which is characterized by high yields, a broad substrate scope, mild reaction conditions, and a unique chemoselectivity. These features enable the synthesis of peptides from amino acid derived α-ketoacids under preservation of the stereochemical information.     

D3h‐Symmetric Porphyrin‐Based Rigid Macrocyclic Ligands for Multicofacial Multinuclear Complexes in a One‐Nanometer‐Sized Cavity

The one‐step synthesis of D_3h‐symmetric cyclic porphyrin trimers 1 composed of three 2,2′‐[4,4′‐bis(methoxycarbonyl)]bipyridyl moieties and three porphyrinatozinc moieties was achieved from a nickel‐mediated reductive coupling of meso‐5,15‐bis(6‐chloro‐4‐methoxycarbonylpyrid‐2‐yl)porphyrinatozinc. Although cyclic trimers 1 were obtained as a mixture that included other cyclic and acyclic porphyrin oligomers, an extremely specific separation was observed only for cyclic trimers 1 when using columns of silica gel modified with pyrenylethyl, cyanopropyl, and other groups. Structural analysis of cyclic trimers 1 was carried out by means of NMR spectroscopy and X‐ray crystallography. Treatment of an η³‐allylpalladium complex with a cyclic trimer gave a tris(palladium) complex containing three η³‐allylpalladium groups inside the space, which indicated that the bipyridyl moieties inside the ring could work as bidentate metalloligands.     

Silicon-Based Integrated Optic Pressure Sensor Using Intermodal Interference between TM-Like and TE-Like Modes

In this paper, a silicon-based integrated optic pressure sensor using an intermodal interference between the fundamental TM-like and TE-like modes is described. The sensor consists of a micromachined rectangular diaphragm and a straight polystyrene optical waveguide passing over the diaphragm. Its sensitivity is theoretically known to be strongly dependent on the position of the waveguide over the diaphragm. To experimentally investigate such dependence, we fabricated a sensor with a 1.2 mm ×10 mm ×20 μm diaphragm, over which waveguides were placed at 50 μm intervals. The measured phase sensitivity was 98 mrad/kPa for the waveguide nearest to the diaphragm edge. The measurement was also carried out for the other waveguides. As theoretically expected, the largest sensitivity was obtained for the waveguide nearest to the edge.     

Light Diffraction of Aligned Polymer Fibers Periodically Dispersed by Phase Separation of Liquid Crystal and Polymer

We have confirmed light diffraction of aligned polymer fibers obtained by a phase separation of an anisotropic-phase solution of liquid crystal and polymer. He—Ne laser light passing through the polymer fibers was scattered in the axis vertical to the fibers, and had two peaks of light intensity symmetrical to the center of the transmitting laser spot. The two peaks were found to be caused by light diffraction due to the periodic polymer-fiber dispersion because the peaks corresponded to values calculated by intervals between the fibers. The periodical fiber networks are considered to be formed by anisotropic spinodal decomposition. This effect can be used to measure the dispersion order of the polymer fibers. © 2004 The Optical Society of Japan     

Facilitated sulfate transfer across the nitrobenzene-water interface as mediated by hydrogen-bonding ionophores.

Facilitated SO4(2-) transfers by hydrogen bond-forming ionophores are investigated across the nitrobenzene (NB)-water interface by using polarography with a dropping electrolyte electrode. Bis-thiourea 1, alpha,alpha'-bis(N'-p-nitrophenylthioureylene)-m-xylene, is found to significantly facilitate the transfer of the highly hydrophilic SO4(2-) whereas its counterpart, N-(p-nitrophenyl)-N'-propylthiourea (ionophore 2), cannot. In contrast to the predominant formation of a 1:1 complex with SO4(2-) in the bulk NB phase, the SO4(2-) transfer assisted by 1 is indeed based on the formation of a 1:2 complex between SO4(2-) and ionophore, even under the condition of [SO4(2-)]aq > [1]org. Such an exclusive formation of the 1:2 (SO4(2-) to ionophore) complex at the NB-water interface is not observed with structurally similar bis-thiourea 3, alpha,alpha'-bis(N'-phenylthioureylene)-m-xylene, where p-nitrophenyl moietes of bis-thiourea 1 are simply replaced by phenyl groups. The facilitated transfer of SO4(2-) with bis-thiourea 1 is further compared to that of HPO4(2-) and H2PO4- across the NB-water interface, which was previously shown to be assisted by 1 through the formation of the 1:1 and 2:1 (anion to ionophore) complexes, respectively. On the basis of these examinations, unique binding behaviors of hydrogen bond-forming ionophores at the NB-water interface are discussed, with a view towards development of ionophore-based anion-selective chemical sensors.     

Curved Ferroelectric Liquid Crystal Matrix Displays Driven by Field-Sequential-Color and Active-Matrix Techniques

This paper describes a curved field-sequential-color matrix display using fast-response ferroelectric liquid crystal. Black matrix and transparent electrode patterns were formed on a thin plastic substrate by a transfer method from a glass substrate. While a composite film of liquid crystal and micro-polymers of walls and fibers was formed between the flexible substrates by printing, laminating and curing processes of a solution of monomers and liquid crystal, the mechanical stability was enhanced by use of multi-functional monomers to form large display panels. The image pixels of the matrix panel were driven by an active matrix scheme using an external switch transistor array at a frequency of 180 Hz for intermittent three-primary-color backlight illumination. The flexible A4-paper-sized color display with 24 × 16 pixels and 60 Hz field frequency was demonstrated by illuminating it with sequential three-primary-color lights from light-emitting diodes of the backlight. Our display system is useful in various information displays because of its freedom of setting and location.