Kinetic study of the crosslinking reaction of 1,2‐polybutadiene with dicumyl peroxide in the absence and presence of vinyl acetate

The crosslinking reaction of 1,2-polybutadiene (1,2-PB) with dicumyl peroxide (DCPO) in dioxane was kinetically studied by means of Fourier transform near-infrared spectroscopy (FTNIR). The crosslinking reaction was followed in situ by the monitoring of the disappearance of the pendant vinyl group of 1,2-PB with FTNIR. The initial disappearance rate (R₀) of the vinyl group was expressed by R₀ = k[DCPO]^0.8[vinyl group]^−0.2 (120 °C). The overall activation energy of the reaction was estimated to be 38.3 kcal/mol. The unusual rate equation was explained in terms of the polymerization of the pendant vinyl group as an allyl monomer involving degradative chain transfer to the monomer. The reaction mixture involved electron spin resonance (ESR)-observable polymer radicals, of which the concentration rapidly increased with time owing to a progress of crosslinking after an induction period of 200 min. The crosslinking reaction of 1,2-PB with DCPO was also examined in the presence of vinyl acetate (VAc), which was regarded as a copolymerization of the vinyl group with VAc. The vinyl group of 1,2-PB was found to show a reactivity much higher than 1-octene and 3-methyl-1-hexene as model compounds in the copolymerization with VAc. This unexpectedly high reactivity of the vinyl group suggested that an intramolecular polymerization process proceeds between the pendant vinyl groups located on the same polymer chain, possibly leading to the formation of block-like polymer. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 4437–4447, 2004     

Synthesis of fluoride garnets {Na3}[M3+2](Li3)F12 (M = Al,Cr, and Fe) from aqueous solution and their properties

The garnet-type fluorides, Na₃M₂Li₃F₁₂ (M = Al, Cr, and Fe) were synthesized as the coprecipitates of ～1 to 10 μm powders from HF solutions. The garnet structures were always obtained under acidic conditions. The incorporation of water molecules into the structure of the Cr and Fe garnets was observed. After heat treatment at 300°C, very small unknown peaks were observed in the X-ray powder pattern in addition to the garnet phase which had a slightly smaller value of the lattice constant than that of hydrous garnets. From the measurement of magnetic properties and Mössbauer effects, the Fe and Cr garnets were found to be paramagnetic with both ions in the trivalent state. Presentation of infrared spectra of the garnets is also included.     

Solvents inducing oxidation of hydroxylamines

Hydroxylamines gradually undergo oxidation to their oximes on being dissolved in organic solvent (e.g. methanol). This phenomenon was followed by (1)H-NMR and liquid chromatography-mass spectrometry (LC-MS). The oxidation rate was estimated from the peak area observed on the mass chromatogram at the protonated molecule or fragment ion on LC-atmospheric pressure chemical ionization (APCI)-MS. The results showed that the oxidation rate of hydroxylamines depended on the solvent type.     

Emulsifier-free emulsion polymerization of tetrafluoroethylene by radiation. I. Effects of reaction conditions on the polymerization rate and polymer molecular weight

The radiation-induced emulsifier-free emulsion polymerization of tetrafluoroethylene was carried out at an initial pressure of 2–25 kg/cm², temperature of 30–110°C, and under a dose rate of 0.57 × 10⁴?3.0 × 10⁴ rad/hr. The rate of polymerization was shown to be proportional to 1.0 and 1.3 powers of the dose rate and initial pressure, respectively, and is maximal at about 70°C. The molecular weight of polytetrafluoroethylene (PTFE) lies in the range of 10⁵?10⁶, increases with reaction time in the early stage of polymerization, and is maximal at 70°C but is almost independent of the dose rate. An interesting discovery is that PTFE, a hydrophobic polymer, forms as a stable latex in the absence of emulsifier. When PTFE latex coagulates during polymerization under certain conditions, the polymerization rate decreases, probably because polymerization proceeds mainly on the polymer particle surface. The observed rate acceleration and successive increase in polymer molecular weight may be due to slow termination of propagating radicals in the rigid PTFE particles.     

Performance of throughout in-capillary derivatization capillary electrophoresis employing an on-line sample and run buffer loading device

We report on the effect on performance of varying the length of the capillary during throughout in-capillary derivatization (TICD) capillary electrophoresis (CE). Performance was evaluated by on-line coupling with a sample and CE runbuffer loading device that was newly introduced for this study. The device was assembled with a low cost using two 5 mm inner diameter (ID) disposable polyethylene syringes. First, a sequence was manually formed consisting of a 200 microL run buffer solution plug, a 100 microL sample plug and another 200 microL run buffer solution plug. Each plug was separated from its neighbor by a 100 microL air plug. When each plug reached the injection point where both a platinum-wire anode and the end of the separation capillary tube were located, 340 V/cm separation voltage (electrophoresis voltage) and 34 V/cm injection voltage were applied to the capillary for 3 s. Then the analytes were derivatized during migration in 50 microm ID capillaries filled with 2 mM o-phthalaldehyde (OPA)/N-acetylcysteine (NAC) in a 20 mM phosphate-borate buffer (pH 10), followed by separating and detecting of OPA derivatives by absorbance of 340 nm. Derivatization, separation, and detection were performed systematically using capillaries which varied in length from 5 to 80 cm. In the case of TICD-CE of a mixture containing 1 mM aspartic acid (Asp) and 20 mM m-nitorophenol (MNP) as a test solution, it was determined that peak area and peak width ratios of Asp to MNP did not depend on capillary length. Enantiomeric separations of DL-alanine (Ala) and Asp were examined using a run buffer consisting of a 45 microM beta-cyclodextrin (CD)-2 mM OPA/NAC-20 mM phosphate-borate buffer (pH 10). Even though the resolution of these enantiomeric pairs decreased with decreasing capillary length, as expected, the peaks corresponding to both enantiomeric amino acids were identified even when a 5 cm capillary was used. An 8-component amino acid mixture was also tested with 5 cm and 10 cm capillaries.     

Four new cycloartane glycosides from Aquilegia vulgaris

Four new cycloartane glycosides, named aquilegiosides G-J, were isolated from the dried aerial parts of Aquilegia vulgaris. Their structures were determined by spectroscopic analysis and chemical evidence.     

Emulsifier-free emulsion polymerization of tetrafluoroethylene by radiation. III. Simultaneous formation of hydrofluoric acid

Simultaneous formation of hydrofluoric acid (HF) in the radiation-induced polymerization of tetrafluoroethylene (TFE) was investigated. HF concentration in PTFE latex was determined mainly by conductometric titration with 0.01 and 0.001N NaOH. The amount of HF formed is almost independent of agitation speed and the amount of n-hexadecane added and is maximal at ca. 70°C corresponding to the rate of polymerization. The rate of HF formation increases with the initial pressure of TFE monomer and dose rate and decreases with polymerization or TFE consumption. This fact suggests that HF is formed mainly by TFE reactions and not by the degradation of PTFE. The mechanism of HF formation in this reaction system in the absence of oxygen is shown in the following two schemes: scheme I is the reaction of TFE with primary radicals (OH·, H·, e) from the radiolysis of water; scheme II is the reaction of water with the species from the radiolysis of TFE. On the assumption that HF is formed only according to scheme I, the G value of HF formation G(HF)_calc can be calculated as 11.25. All observed G values G(HF)_obs are larger than G(HF)_calc. When the polymerization is carried out at 20 kg/cm² under various dose rates, G(HF)_obs increases with the dose rate. When the polymerization is carried out at 3.0 × 10⁴ rad/hr under various pressures, G(HF)_obs decreases with the decrease in pressure from 20 to 2 kg/cm² and is fairly close to G(HG)_calc at 2 kg/cm². This indicates that HF formation is due mainly to scheme II at high pressure (in the presence of enough TFE) and to scheme I as the pressure is lowered.     

Supramolecular chirogenesis in zinc porphyrins: interaction with bidentate ligands,formation of tweezer structures,and the origin of enhanced optical activity

The complexation behavior, binding properties, and spectral parameters of supramolecular chirality induction in the achiral host molecule, syn (face-to-face conformation) ethane-bridged bis(zinc porphyrin), upon interaction with chiral bidentate guests (diamines and amino alcohols) have been studied by means of UV-vis, CD, fluorescence, (1)H NMR, and ESI MS techniques. It was found that the guest structure plays a decisive role in the chirogenesis pathway. The majority of bidentate ligands (except those geometrically unsuitable) exhibit two major equilibria steps: the first guest ligation leading to formation of the 1:1 host-guest tweezer structure (K(1)) and the second guest molecule ligation (K(2)) forming the anti bis-ligated species (1:2). The second ligation is much weaker (K(1) > K(2)) due to the optimal geometry and stability of the 1:1 tweezer complex. The enhanced conformational stability of the tweezer complex ensures an efficient chirality transfer from the chiral guest to the achiral host, consequently inducing a remarkably high optical activity in the bis-porphyrin.