Polypyrrole–montmorillonite nanocomposite as sorbent for solid‐phase microextraction of phenolic compounds in water

A fiber‐coated polypyrrole–montmorillonite nanocomposite was prepared for solid‐phase microextraction. The fiber coating can be prepared easily; it is mechanically stable and exhibits relatively high thermal stability. The prepared fiber was evaluated for the extraction of some phenolic compounds from aqueous sample solutions by gas chromatography–mass spectrometry. The effects of the extraction and desorption parameters including extraction time, extraction temperature, stirring rate, ionic strength, pH and desorption temperature and time have been studied. At optimum conditions, the repeatability for one fiber (n = 5), expressed as % relative standard deviation was between 6.5 and 7.8% for the phenolic compounds. The detection limits for the studied phenolic compounds were between 0.05–1.3 ng/mL. The developed method offers the advantage of being simple to use, with shorter analysis time, lower cost, thermal stability of the fibers, and high relative recovery in comparison to conventional methods of analysis.     

Microextraction of phenolic compounds using a fiber coated with a polyaniline-montmorillonite nanocomposite

Microchimica Acta - A highly porous fiber coated polyaniline/montmorillonite clay was prepared for solid-phase microextraction. The nanocomposite was synthesized by in-situ polymerization. The...     

Synthesis of layered zinc hydroxide intercalated with dodecyl sulfate organic–inorganic hybrid nanocomposite as a fiber coating for the headspace solid‐phase microextraction of aromatic hydrocarbons from water

We describe the synthesis of a layered zinc hydroxide‐dodecyl sulfate organic–inorganic hybrid nanocomposite as a new solid‐phase microextraction fiber. The fiber coating can be prepared easily in a short time and the reaction is at room temperature; it is mechanically stable and exhibits relatively high thermal stability. The synthesized layered zinc hydroxide‐dodecyl sulfate nanocomposite was successfully prepared and immobilized on a stainless steel wire and evaluated for the extraction of aromatic compounds from aqueous sample solutions in combination with gas chromatography and mass spectrometry. The method yields good results for some validation parameters. Under optimum conditions (extraction time: 15 min, extraction temperature: 50°C, desorption time: 1 min, desorption temperature: 250°C, salt concentration: 0.5 g/mL), the limit of detection and dynamic linear range were 0.69–3.2 ng/L and 10–500 ng/L, respectively. The method was applied to the analyses of benzene, toluene, ethylbenzene, and o‐, p‐, and m‐xylenes in two real water samples collected from the Aji river and Mehran river, Tabriz, Iran. Under optimum conditions, the repeatability and reproducibility for one fiber (n = 3), expressed as the relative standard deviation, was 3.2–7.3% and 4.2–11.2% respectively. The fibers are thermally stable and yield better recoveries than conventional methods of analysis.     

Biofabrication of a flexible and conductive 3D polymeric scaffold for neural tissue engineering applications; physical,chemical, mechanical,and biological evaluations

Tissue engineering approach aims to overcome the transplant drawbacks and facilitate tissue repair and regeneration. Here, a new conductive, highly porous, and flexible polycaprolactone/gelatin/polypyrrole/graphene 3D scaffolds for nerve tissue repair is presented. A simple and efficient porogen leaching fabrication method is applied to create a 3D network with a pore radius of 3.8 ± 0.7 to 4.2 ± 0.8 μm with an exceptional uniform circular porous structure. The conductivity of the polymeric scaffold without graphene, in wet conditions, was found to be 0.78 ± 0.1 S.m⁻¹ and it increased to 3.3 ± 0.2 S.m⁻¹ for the optimized sample containing 3wt% graphene (G3). Tensile strength was measured at 163 KPa for the base sample (without graphene) and improved to 526 KPa for G3 sample. Following 42 days of incubation in PBS, 32.5% degradation for the base sample (without graphene) was observed. The cell study demonstrated a non-cytotoxic nature of all scaffolds tested and the cells had mostly stretched and covered the surface. Overall, the sum of results presented in this study demonstrate a simple fabrication platform with extraordinary aspects that can be utilized to mimic the native conductive tissue properties, and also because of its flexibility it can easily be rolled into a nerve conduit to fill gaps in nerve tissue regeneration.     

Preparation of Multilayered Polymeric Structures Using a Novel Four‐Needle Coaxial Electrohydrodynamic Device

Coaxial four‐needle electrohydrodynamic forming is applied for the first time to prepare layered structures in both particle and fiber form. Four different biocompatible polymers, polyethylene glycol, poly (lactic‐co‐glycolic acid), polycaprolactone, and polymethylsilsesquioxane, are used to generate four distinct layers confirmed using transmission and scanning electron microscopy combined with focused ion beam milling. The incorporation and release of different dyes within the polymeric system of four layers are demonstrated, something that is much desired in modern applications such as the polypill where multiple active pharmaceutical ingredients can be combined to treat numerous diseases.