Validated Stability-Indicating GC-MS Method for Characterization of Forced Degradation Products of Trans-Caffeic Acid and Trans-Ferulic Acid

When dealing with simple phenols such as caffeic acid (CA) and ferulic acid (FA), found in a variety of plants, it is very important to have control over the most important factors that accelerate their degradation reactions. This is the first report in which the stabilities of these two compounds have been systematically tested by exposure to various different factors. Forced degradation studies were performed on pure standards (trans-CA and trans-FA), dissolved in different solvents and exposed to different oxidative, photolytic and thermal stress conditions. Additionally, a rapid, sensitive, and selective stability-indicating gas chromatographic-mass spectrometric method was developed and validated for determination of trans-CA and trans-FA in the presence of their degradation products. Cis-CA and cis-FA were confirmed as the only degradation products in all the experiments performed. All the compounds were perfectly separated by gas chromatography (GC) and identified using mass spectrometry (MS), a method that additionally elucidated their structures. In general, more protic solvents, higher temperatures, UV radiation and longer storage times led to more significant degradation (isomerization) of both trans-isomers. The most progressive isomerization of both compounds (up to 43%) was observed when the polar solutions were exposed to daylight at room temperature for 1 month. The method was validated for linearity, precision as repeatability, limit of detection (LOD) and limit of quantitation (LOQ). The method was confirmed as linear over tested concentration ranges from 1−100 mg L⁻¹ (r²s were above 0.999). The LOD and LOQ for trans-FA were 0.15 mg L⁻¹ and 0.50 mg L⁻¹, respectively. The LOD and LOQ for trans-CA were 0.23 mg L⁻¹ and 0.77 mg L⁻¹, respectively.     

Comparison of two models for managing reliability growth during product design

Relying on reliability growth testing to improve system designis neither usually effective nor efficient. Instead it is importantto design in reliability. This requires models to estimate reliabilitygrowth in the design that can be used to assess whether goalreliability will be achieved within the target timescale forthe design process. Many models have been developed for analysisof reliability growth on test, but there has been much lessattention given to reliability growth in design. This paperdescribes and compares two models: one motivated by the practicalengineering process; the other by extending the reasoning ofstatistical reliability growth modelling. Both models are referencedin the recently revised edition of international standard IEC61164. However, there has been no reported evaluation of theirproperties. Therefore, this paper explores the commonalitiesand differences between these models through an assessment oftheir logic and their application to an industrial example.Recommendations are given for the use of reliability growthmodels to aid management of the design process and to informproduct development.     

Compositions for health products obtained by treatment of tomato with beta-cyclodextrin

The aim of this work was to produce lycopene-containing powders from tomato products by a solvent-free method making use of β-cyclodextrin (βCD). Powders were prepared by spray-drying a tomato concentrate (TC), one of the most bioavailable form of lycopene, after mechanical treatment with βCD in different weight ratios. The obtained product was centrifuged to eliminate partly food matrix and characterized for the amount of lycopene hydrodispersed/hydrosolubilized in the aqueous fraction. The chemical antioxidant activity of sera was evaluated too. Powders obtained by spray-drying sera exhibited good flow properties, a lycopene content between 0.4 and 1.09 mg/g and excellent water dispersability. The process developed, which makes use of βCD for the treatment of tomato products, turns to be of great interest to obtain a bulk material for nutraceuticals displaying superior biovailability of lycopene.     

Cyclic trihydroxamic acid derivatives

In the crystal structures of two cyclic trihydroxamic acid derivatives containing the same substructure unit, viz. 1,3,5‐trihydroxy‐1,3,5‐triazinane‐2,4,6‐trione dihydrate, C₃H₃N₃O₆·2H₂O, (I), and 1,3,5‐benz­yloxy‐1,3,5‐triazinane‐2,4,6‐trione, C₂₄H₂₁N₃O₆, (II), there is no significant difference in the geometric parameters. In (I), there are 11 hydrogen bonds of the O—H⋯O type inter­connecting the mol­ecules in a three‐dimensional network, while in (II) there are only two weak C—H⋯O hydrogen bonds. The results of IR spectroscopic analysis are in good agreement with the crystallographic study.     

On the reliability of unsaturated hydraulic conductivity calculated from the moisture retention curve

In comparison with direct measurements of unsaturated hydraulic conductivity, the methods of calculations from the moisture retention curve are attractive for their fast and simple use and low cost. These are the main reasons for their increasing use, mainly in spatial variability studies. On the other hand, it is known that their applicability is limited. The possibility of the use of the retention curve to indirectly determine hydraulic conductivities is analyzed as follows. The theoretical derivation of the relationK(h) – (h) is briefly discussed with regards to potential sources of inaccuracy. The sensitivity of the algorithm forK(h) calculation is studied as a response to possible inaccuracies in the retention curve determination. Conclusions about the usability of calculated hydraulic conductivities are drawn.     

Solid-state interactions and drug release of teicoplanin in binary combinations with peracetylated α-, β-, and γ-cyclodextrins

Triacetyl α-cyclodextrin, triacetyl β-cyclodextrin and triacetyl γ-cyclodextrin were tested as possible hydrophobic carriers to prolong the release of hydrophilic teicoplanin (TCP). Physical–chemical characterization of individual components, drug-carrier physical mixtures at 0.5, 0.67 and 0.75 mass fraction of carrier, and the respective interaction products by kneading or evaporative crystallization under microwave irradiation was carried out using differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). In vitro drug release in pH 7.4 phosphate buffer at 37 °C was determined by intrinsic dissolution rate (IDR) measurements on non disintegrating compressed discs. Solid-state interactions of TCP with triacetyl α-cyclodextrin by evaporative crystallization and kneading and with triacetyl β-cyclodextrin by evaporative crystallization (probably resulting in carrier amorphization) were demonstrated. The role of carrier hydrophobicity, carrier mass fraction and preparation method of solid drug-carrier combinations on solid-state drug-carrier interactions and slowing down of TCP release was assessed. Modulation of drug release can be achieved using TCP-triacetyl γ-cyclodextrin combinations at 0.5 mass fraction of carrier.     

FLUORESCENCE OF Euglena gracilis PHOTORECEPTOR PIGMENT: AN in vivo MICROSPECTROFLUOROMETRIC STUDY

Abstract— The spectroscopic characterization of the photoreceptor pigment is one of the main questions in the study of the photosensory transduction chains in photomotile microorganisms. One of the possible techniques that can be used is in vivo microspectrofluorometry. By means of a tunable dye-laser microspectrofiuorometer developed by us, we have investigated some of the spectroscopic properties of the photoreceptor pigment of the green flagellate Euglena gracilis. The in vivo fluorescence excitation spectrum has been determined and the fluorescence quantum yield has been measured. The results show that flavins are indeed present in the paraflagellar body of E. gracilis and that their fluorescence quantum yield is much lower than that of a free flavin. An estimate of the order of magnitude of the rate constants for primary molecular reactions is tentatively given.     

Determination of the Lipophilicity of Xanthines by Reversed-Phase Liquid Chromatography

JPC – Journal of Planar Chromatography – Modern TLC -     

Comparison of solid-phase microextraction and purge-and-trap methods for the analysis of the volatile fraction of butter

The volatile fraction of butter stored at three different temperatures was investigated to monitor quality during commercial shelf-life (90 days). Two different extraction techniques were compared: dynamic headspace (purge-and-trap), and static headspace (solid-phase microextraction, SPME). As expected, the dynamic extraction provided a generally higher amount of volatile compounds than that obtained by SPME, but, with reference to individual compounds, SPME seemed to provide better extraction for volatiles having a higher molecular mass. Despite the different performances, both methods were able to detect volatiles useful for evaluating changes during storage.     

The polysaccharide extracts from the fungi Coprinus comatus and Coprinellus truncorum do exhibit AChE inhibitory activity

The polysaccharide (PSH) extracts from the edible mushroom species Coprinus comatus and Coprinellus truncorum were screened in liquid for their acetylcholinesterase inhibitory (AChE) activity. Both extracts were found to display inhibition of the aforementioned enzyme reaching similar IC₅₀ values of 0.62 ± 0.07 and 0.61 ± 0.03 mg/mL, respectively. According to the means of FTIR spectroscopy, these PSH extracts mostly contained β-glucans. However, the presence of some proteins and polyphenolics as minor ingredients were also detected. Compared with existing literature data for anti-AChE activity of the sugar samples, the findings within this study may be treated as a profound bioactivity. Consequently, this study puts some light on the possible use of the screened macrofungi in the palliative treatment of Alzheimer’s disease.