Curved Ferroelectric Liquid Crystal Matrix Displays Driven by Field-Sequential-Color and Active-Matrix Techniques

This paper describes a curved field-sequential-color matrix display using fast-response ferroelectric liquid crystal. Black matrix and transparent electrode patterns were formed on a thin plastic substrate by a transfer method from a glass substrate. While a composite film of liquid crystal and micro-polymers of walls and fibers was formed between the flexible substrates by printing, laminating and curing processes of a solution of monomers and liquid crystal, the mechanical stability was enhanced by use of multi-functional monomers to form large display panels. The image pixels of the matrix panel were driven by an active matrix scheme using an external switch transistor array at a frequency of 180 Hz for intermittent three-primary-color backlight illumination. The flexible A4-paper-sized color display with 24 × 16 pixels and 60 Hz field frequency was demonstrated by illuminating it with sequential three-primary-color lights from light-emitting diodes of the backlight. Our display system is useful in various information displays because of its freedom of setting and location.     

Development of Non-Halogen Flame Retardant Optical Fiber and Optical Fiber Cord

A non-halogen highly flame-retardant 0.9mm optical fiber and 2.0mm simplex optical cord, which are harmonized with the ecosystem, have been developed. The characteristics of them are presented in this paper.     

Numerical study on performance of disk MHD generator using frozen inert gas plasma

In an magnetohydrodynamic (MHD) generator using a frozen inert gas plasma (FIP), the availability of a frozen argon plasma, the influence of plasma uniformity at the generator inlet on the performance, and the feasibility of a large-scale generator are numerically examined by /spl gamma/-/spl theta/ two-dimensional simulation. The FIP is produced by pre-ionizing inert gas without an alkali metal seed at the generator inlet, then the ionization degree of the plasma is kept almost constant in the whole of the channel because of considerable slow recombination of the inert gas just like frozen reaction plasma. It is found that not only helium, but also argon frozen plasma MHD generation is realized, although highly accurate control of inlet ionization degree is necessary for argon. It is important to reduce the nonuniformity of plasma properties at the generator inlet in order to raise the maximum enthalpy extraction ratio. Even for the large-scale generator with 1000-MW thermal input, the ionization degree is kept almost constant in the whole of the channel and the high performance is obtainable. This result is extremely attractive for the FIP MHD generator.     

Molecular scale structure formation by folding

A conception of a structure formation suitable for nano-technology is proposed, which is programmable and suitable for mass production-like lithography. This conception utilizes the controlled folding of chains like the scan-lines of television. Its possibility and property were studied theoretically using the modeled chains consist of beads. By adopting the interaction among the beads which can distinguish the kind of the partner by its polarity and is chiral to break the chiral symmetry of the folded state, the special chains which have the unique ground states could be designed. In these ground states, the chains are folded like the scan-lines of television. The thermodynamic properties of the suggested chains were studied by the Monte Carlo simulations and the suggested chains showed the phase-transition-like behavior which is distinct compared to both the random chains and the chain that has only the non-specific attraction. The size dependence and the effects of adding the non-specific attraction and modifying the border of the folded conformation were also studied.     

Mass spectrometric analysis of low molecular mass polyesters by laser desorption/ionization on porous silicon

A low molecular mass polyester was analyzed by desorption/ionization on porous silicon (DIOS) mass spectrometry. The results were compared with those of matrix-assisted laser desorption ionization (MALDI) mass spectrometry using matrixes of alpha-cyano-4-hydroxycinnamic acid (CHCA) and 10,15,20-tetrakis(pentafluorophenyl)porphyrin (F20TPP). The CHCA matrix was not suitable for characterization of low molecular mass components of the polyester because the matrix-related ions interfered with the component ions. On the other hand, the F20TPP matrix showed no interference because no matrix-related ions appeared below m/z 822. However, the solvent selection for determining optimal conditions of sample preparation was limited, because F20TPP does not dissolve readily in any of the available organic solvents. In the DIOS spectra, the polymer ions were observed at high sensitivity without a contaminating ion. No matrix is needed for DIOS spectra of low molecular mass polyesters, facilitating sample preparation and selectivity of a precursor ion in post-source decay measurements.     

Synthesis of novel organoselenium as catalyst for Baeyer-Villiger oxidation with 30% H2O2

A novel diselenide was synthesized in good yield via only four steps from phenol, and was employed as the catalyst for the Baeyer-Villiger oxidation with 30% H₂O₂ to obtain lactones in good yields.     

Ruthenium(II)-catalyzed hydrogenation of carbon dioxide to formic acid. Theoretical study of real catalyst, ligand effects, and solvation effects

Ruthenium-catalyzed hydrogenation of carbon dioxide to formic acid was theoretically investigated with DFT and MP4(SDQ) methods, where a real catalyst, cis-Ru(H)2(PMe3)3, was employed in calculations and compared with a model catalyst, cis-Ru(H)2(PH3)3. Significant differences between the real and model systems are observed in CO2 insertion into the Ru(II)-H bond, isomerization of a ruthenium(II) eta1-formate intermediate, and metathesis of the eta1-formate intermediate with a dihydrogen molecule. All these reactions more easily occur in the real system than in the model system. The differences are interpreted in terms that PMe3 is more donating than PH3 and the trans-influence of PMe3 is stronger than that of PH3. The rate-determining step is the CO2 insertion into the Ru(II)-H bond. Its deltaG(o++) value is 16.8 (6.8) kcal/mol, where the value without parentheses is calculated with the MP4(SDQ) method and that in parentheses is calculated with the DFT method. Because this insertion is considerably endothermic, the coordination of the dihydrogen molecule with the ruthenium(II)-eta1-formate intermediate must necessarily occur to suppress the deinsertion. This means that the reaction rate increases with increase in the pressure of dihydrogen molecule, which is consistent with the experimental results. Solvent effects were investigated with the DPCM method. The activation barrier and reaction energy of the CO2 insertion reaction moderately decrease in the order gas phase > n-heptane > THF, while the activation barrier of the metathesis considerably increases in the order gas phase < n-heptane < THF. Thus, a polar solvent should be used because the insertion reaction is the rate-determining step.     

Synthesis of large macrocyclic tetraaza compounds with a methylene backbone: Cyclo[-NH- (CH2)n-]4, (n = 6, 7, 8, 9 and 10). The formation of 28-, 32-, 36-, 40- and 44-membered rings

A series of macrocyclic tetraamines with 28-, 32-, 36-, 40- and 44-membered rings have been efficiently prepared from the corresponding ditosylamide and monobromoalcohol derivatives in 6 steps via a double condensation reaction. Overall yields were: 41, 41, 46, 29, and 33%, respectively, for 1,8,15,22-tetraazacyclooctacontane ( 11a ), 1,9,17,25-tetraazacyclodotriacontane ( 11b ), 1,10,19,28-tetraazacyclohexatriacontane ( 11c ), 1,11,21,31-tetraazacyclotetracontane ( 11d ) and 1,12,23,34-tetraazacyclotetratetracontane ( 11e ).