Light Diffraction of Aligned Polymer Fibers Periodically Dispersed by Phase Separation of Liquid Crystal and Polymer

We have confirmed light diffraction of aligned polymer fibers obtained by a phase separation of an anisotropic-phase solution of liquid crystal and polymer. He—Ne laser light passing through the polymer fibers was scattered in the axis vertical to the fibers, and had two peaks of light intensity symmetrical to the center of the transmitting laser spot. The two peaks were found to be caused by light diffraction due to the periodic polymer-fiber dispersion because the peaks corresponded to values calculated by intervals between the fibers. The periodical fiber networks are considered to be formed by anisotropic spinodal decomposition. This effect can be used to measure the dispersion order of the polymer fibers. © 2004 The Optical Society of Japan     

Fracture mechanism of liquid‐crystalline epoxy resin systems with different phase structures

A liquid‐crystalline epoxy resin was cured at two different temperatures. The phases of the cured systems clearly showed isotropic and nematic polydomain structures, which depended on the curing temperature. The fracture toughness of the systems was measured, and the fracture mechanism was investigated with polarized IR measurements. The nematic polydomain structure system showed considerably higher fracture toughness than the isotropic structure. Moreover, both systems exhibited a reorientation of the network chains near the fracture surface during the fracture process, and the region of the network reorientation in the nematic polydomain structure system was larger than that in the isotropic structure system. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 4044–4052, 2004     

Large-volume injection electrothermal AAS combined with tungsten-treated pyrolytic graphite furnace: determination of cadmium in tap, snow and river water samples with phosphate modifier.

A large-volume (100 microl) injection-ETAAS with W-treated PG furnace combined with a phosphate modifier was applied to the determination of unpolluted levels of Cd in tap, snow and river-water samples. The limit of detection of 1.1 ng l(-1) was observed for a 4 w/v% NH4H2PO4 modifer. Matrix interference studies were tested for major ion species well found in fresh water. The direct determination of Cd in certified river water (12 +/- 2 ng l(-1)) was carried out and the observed value was in agreement with the certified one. The good recoveries of Cd added to real environmental water samples were also observed. This method was applied to the determination of Cd in unpolluted environmental water samples.     

Cerasome as an Organic-Inorganic Vesicular Nanohybrid: Characterization of Cerasome-Forming Lipids having a Single or a Dual Trialkoxysilyl Head

Morphological characterization of the organic-inorganic vesicular nanohybrids, Cerasomes, was performed in aqueous media from two aspects. Firstly, a novel Cerasome-forming lipid having two triethoxysilyl groups in the head moiety was synthesized and the physical property of the Cerasome was investigated. While the morphological stability of the Cerasomes, as evaluated from the vesicular collapse behavior against a micelle-forming nonionic surfactant, Triton-X 100, was extremely higher than that of the conventional phospholipid liposome, the stabilities were comparable to each other for the Cerasomes derived from the dual- and single-head lipids. On the other hand, the surface property of the Cerasome formed with the dual-head lipid more closely resembled the colloidal silica particles rather than that derived from the single-head lipid, as suggested by zeta-potential measurements. Secondly, the effect of the media pH on the morphological stability of the Cerasome formed with the single-head lipid was evaluated and appeared as a time difference in obtaining the morphological stability of the Cerasome. These morphological characteristics of the Cerasomes could be mainly owing to the development of the siloxane network on the vesicular surface.     

Non-destructive rapid analysis of brominated flame retardants in electrical and electronic equipment using Raman spectroscopy.

Using Raman spectroscopy without any preparation, we analyzed the brominated flame retardant, polybromodiphenyl ethers (PBDEs), which has been prohibited by the European Union. The typical Raman bands of PBDEs, which are clearly different from those of other brominated flame retardants, are from 100 to 300 cm(-1). In our analysis, the detection limit was about 100 ppm, and the analysis took about 1 min, whereas the usual method of solvent extraction using gas chromatography/mass spectroscopy takes 50 h.     

Structural characterization of polypyrrole in the solid state by high resolution 15N NMR spectroscopy [II]

The solid-state ¹⁵N CP/MAS NMR spectra and ¹⁵N spin-lattice relaxation times (T₁) of doped and dedoped ¹⁵N-labeled polypyrroles prepared by electrochemical polymerization, have been measured by means of high-resolution solid-state ¹⁵N NMR. The ¹⁵N signal of polypyrrole consists of four peaks decomposed by line shape analysis. The four peaks obtained have been assigned to the various structures of polypyrrole. Further, the half-width of the ¹⁵N NMR spectra of polypyrroles is discussed as related to the electrical conductivity. © 1995 John Wiley & Sons, Inc.     

Synthesis of 3-hydroxyindolin-2-one alkaloids, (±)-donaxaridine and (±)-convolutamydines A and E, through enolization-Claisen rearrangement of 2-allyloxyindolin-3-ones

Claisen rearrangement triggered by enolization of 2-allyloxyindolin-3-ones with DBU was performed in order to prepare 3-allyl-3-hydroxyindolin-2-ones. Total synthesis of 3-hydroxyindolin-2-one alkaloids, (±)-donaxaridine, as well as (±)-convolutamydines A and E, was achieved by transformation of the allyl moiety of 3-allyl-3-hydroxyindolin-2-ones.     

Influence of the network chain orientation on the fracture toughness of a mesogenic epoxy resin modified with CTBN

A biphenol‐type epoxy resin, which had a mesogenic group in the backbone moiety, was modified with carboxy‐terminated butadiene acrylonitrile copolymer (CTBN) as a reactive elastomer, and its fracture toughness was measured. With the addition of CTBN, the fracture toughness of the biphenol‐type epoxy resin significantly increased and became significantly higher than that of a bisphenol A‐type epoxy resin modified with CTBN. The network chain orientation in the cured biphenol‐type epoxy resin system was clearly observed during the fracture process with polarized microscopy Fourier transform infrared measurements, although such a phenomenon was not observed in the bisphenol A‐type epoxy resin system. The high toughness of the cured biphenol‐type system was clearly due to the consumption of the mechanical energy by a large deformation of the matrix resin due to the orientation of the network chains during the fracture process. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1198–1209, 2003     

Magneto-Optical Measurement of Organic Conductor Using Rotational Cavity System

We have developed a new magneto-optical measurement system using a rotational cavity system equipped with a millimeter vector network analyzer and a 14 T solenoid type super conducting magnet. The measurement can be performed in the transmission configuration down to 1.6 K. The results of the precise angular dependence measurement of quasi-one-dimensional organic conductor (DMET)₂I₃ using the new system are shown, and its Fermi surface will be discussed in connection with the previous reports.