Improvement in flow-sheet of extraction chromatography for trivalent minor actinides recovery

Journal of Radioanalytical and Nuclear Chemistry - Extraction chromatography flow-sheet employing octyl(phenyl)-N,N-diisobutylcarbonoylmethylphosphine oxide and bis(2-ethylhexyl) hydrogen phosphate...     

Path to achieving molecular dispersion in a dense reactive mixture

A uniform dispersion of reactants is necessary to achieve a complete reaction involving multicomponents. In this study, we have examined the role of plasticizer in the reaction of two seemingly unlikely reactants: a highly crystalline hexamethylenetetramine (HMTA) and a strongly hydrogen bonded phenol formaldehyde resin. By combining information from NMR, infrared spectroscopy and differential scanning calorimetry, we were able to determine the role of specific intermolecular interactions necessary for the plasticizer to dissolve the highly crystalline HMTA and to plasticize the phenol formaldehyde resin in this crosslinking reaction. The presence of the plasticizer increased the segmental mobility, disrupted the hydrogen bonded matrix, and freed the hydroxyl units, which further increased the solubility of the HMTA. Both the endothermic and exothermic transitions are accounted for in the calorimetric data obtained. For the first time, it is possible to obtain the effective molar ratio of each component needed to complete the crosslinking reaction efficiently. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 1519–1526     

Application of pressure sensitive paint measurement to a low-solidity cascade diffuser of a transonic centrifugal compressor

A pressure sensitive paint (PSP) measurement has been known as a pressure field measurement technique based on the oxygen quenching phenomenon of luminescence of specific luminophores. A PSP measurement was applied for pressure field measurement in a low-solidity circular cascade diffuser of a single-stage transonic centrifugal compressor with 5 in pressure ratio for HFC134a gas. The oxygen concentration was about 500 ppm. Ru (bath-phen) was adsorbed on a silica-gel thinlayer chromatography sheet, and the sheet was pasted onto the side-wall between the cascade vanes. A drastic change in luminescent intensity was recognized during a surge condition. Also the pressure variations based on luminescent intensity agreed well with the pressure fluctuations measured using a semiconductor pressure sensor with high-frequency-response. It was shown that a PSP measurement worked well to investigate the unsteady pressure fields in a circular cascade diffuser of a transonic centrifugal compressor. Moreover, the time response of PSP becomes clear as a problem to be overcome for the present.     

Dynamic and subjective responses of seated subjects exposed to simultaneous vertical and fore-and-aft whole-body vibration: The effect of the phase between the two single-axis components

Subjective and dynamic responses of seated subjects exposed to simultaneous vertical and fore-and-aft sinusoidal whole-body vibration were investigated. The effect of the phase difference between the vertical and the fore-and-aft vibration on the responses was of a particular interest in this study. Fifteen subjects were exposed to dual-axis vibrations at six frequencies (2.5-8 Hz) and at eight phases between the two single-axis components (0-315°). The magnitude of vibration in each axis was constant at 0.7 m s⁻² rms. Discomfort caused by vibration was measured by the method of magnitude estimation. The motion of the body were measured at the head and three locations along the spine with accelerometers attached to the body surface. The most significant effect of the phase between the two single-axis components on the discomfort was observed at 5 Hz: about 40% difference in the median discomfort estimate caused by changing the phase. The transmissibilities from vertical seat vibration to vertical motions of the spine varied from 0.5 to 2.0 by changing the phase between the two single-axis components at frequencies from 2.5 to 5 Hz. The effect of the phase observed in the dynamic response was not predicted by the superposition of the responses to each single-axis vibration. The discomfort caused by the dual-axis vibration tended to be correlated better with the combinations of the dynamic responses measured in the two axes than with the dynamic responses in a single axis.     

Complex impedance spectra of chip inductor using Li–Zn–Cu–Mn ferrite

A multi-layer chip inductor (MCI) was fabricated using polycrystalline Li–Zn–Cu–Mn ferrite and the green-sheet technique, and its complex impedance spectrum was evaluated with the help of numerical calculations. The complex impedance spectra of the MCI component using Ni–Zn–Cu ferrite, which have been widely used for this application, were very sensitive to the residual stress and deviated much from the calculated values; however, it was found that the complex impedance spectrum of the MCI component using Li–Zn–Cu–Mn ferrite is quite well reproduced by calculation, where the complex permittivity and permeability of the polycrystalline ferrite as well as the MCI dimensions, were used. It implied that the magneto-striction effect was negligible in case of MCI using Li–Zn–Cu–Mn ferrite, and that the difference was related to magneto-strictive coefficient of the polycrystalline ferrite. Consequently, utilization of Li–Zn–Cu–Mn ferrite enabled us to easily design the complex impedance of MCI component.     

High-throughput characterization of local conductivity of Nd0.9Ca0.1Ba2Cu3O7−δ thin film by the low-temperature scanning microwave microscope

We developed a scanning microwave microscope (SμM) designed for high-throughput electric-property screening as well as for rapid construction of electronic phase diagrams at low temperatures. As a sensor probe, we used a high-Qλ/4 coaxial cavity resonator to which a thin needle with ball-tip end was attached. The sensor module was mounted on the low-temperature XYZ stage, which allowed us to map out the change of resonance frequency and quality factor due to the local tip-sample interaction at low temperatures. From the measurements of combinatorial thin films, such as Ti_1−xCo_xO_2−δ and Nd_0.9Ca_0.1Ba₂Cu₃O_7−δ (NCBCO), it was demonstrated that this SμM system has enough performance for the high-throughput characterization of sample conductance under variable temperature conditions.     

Discrimination of carbonyl groups of meso-α-diketones with Horner-Wadsworth-Emmons reagent of chiral binaphthyl esters

Asymmetric Horner-Wadsworth-Emmons reactions of selected meso-α-dicarbonyl compounds with chiral phosphonate reagents, which possessed axially dissymmetric 1,1′-bi-2- or 8-naphthol at the carboxylate moiety as a chiral auxiliary, were examined. The reactions proceeded smoothly with good chemical yields as well as with high diastereoselectivities. Z-olefins were preferentially formed, and it was found that the free hydroxy group at the 2′- or 8′-position on the naphthalene ring plays a crucial role in the high diastereoselectivity, probably due to a complex-induced proximity effect. Mechanistic considerations are also described.     

FMS scheduling based on timed Petri Net model and reactive graph search

This paper presents a new scheduling method for manufacturing system based on the Timed Petri Net model and a reactive fast graph search algorithm. The following two typical problems are addressed in this paper. (1) Minimization of the maximum completion time. (2) Minimization of the total tardiness. As for the problem (1), a new search algorithm which combines the RTA^∗ and a rule-based supervisor is proposed. As for problem (2), the original Petri Net model is converted to its reverse model and the algorithm developed for the problem (1) is applied, regarding the due date as the starting time in the reverse model. Some numerical experiments are carried out to demonstrate usefulness of our algorithm.