Room-Temperature,Metal-Free,and One-Pot Preparation of 2H-Indazoles through a Mills Reaction and Cyclization Sequence

The Mills reaction and cyclization of readily available 2-aminobenzyl alcohols and nitrosobenzenes using thionyl bromide provided 2H-indazoles in up to 88 % yields. In the metal-free process, acetic acid played a crucial role for the both Mills reaction and cyclization. A brominated 2H-indazole could also be obtained through the one-pot sequence.     

Ultrahigh‐molecular‐weight‐polyethylene‐fiber surface treatment by electron‐beam‐irradiation‐induced graft polymerization and its effect on adhesion in a styrene–butadiene rubber matrix

Aiming to develop a high‐performance fiber‐reinforced rubber from styrene–butadiene rubber (SBR), we applied a special technique using electron‐beam (EB)‐irradiation‐induced graft polymerization to ultrahigh‐molecular‐weight‐polyethylene (UHMWPE) fibers. The molecular interaction between the grafted UHMWPE fibers and an SBR matrix was studied through the evaluation of the adhesive behavior of the fibers in the SBR matrix. Although UHMWPE was chemically inert, two monomers, styrene and N‐vinyl formamide (NVF), were examined for graft polymerization onto the UHMWPE fiber surface. Styrene was not effective, but NVF was graft‐polymerized onto the UHMWPE fibers with this special method. A methanol/water mixture and dioxane were used as solvents for NVF, and the effects of the solvents on the grafting percentage of NVF were also examined. The methanol/water mixture was more effective. A grafting percentage of 16.4% was the highest obtained. This improved the adhesive force threefold with respect to that of untreated UHMWPE fibers. These results demonstrated that EB irradiation enabled graft polymerization to occur even on the inert surface of UHMWPE fibers. However, the mechanical properties of the fibers could be compromised according to the dose of EB irradiation. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2595–2603, 2004     

Non-destructive rapid analysis of brominated flame retardants in electrical and electronic equipment using Raman spectroscopy.

Using Raman spectroscopy without any preparation, we analyzed the brominated flame retardant, polybromodiphenyl ethers (PBDEs), which has been prohibited by the European Union. The typical Raman bands of PBDEs, which are clearly different from those of other brominated flame retardants, are from 100 to 300 cm(-1). In our analysis, the detection limit was about 100 ppm, and the analysis took about 1 min, whereas the usual method of solvent extraction using gas chromatography/mass spectroscopy takes 50 h.     

Improved detectability with a polymer-based trapping device in rapid HPLC analysis for ultra-low levels of bisphenol A (BPA) in environmental samples.

A new high-performance liquid chromatography (HPLC) method has been developed to detect ultra-low concentrations of bisphenol-A (BPA) (below 1 ng/L (ppt)) using column switching electrochemical detection (ECD). The results were superior to those obtained from manual pretreatment procedure with membrane stationary phase. BPA is inherently ubiquitous in the environment, including tools and solvents used for its analysis; to obtain meaningful results, therefore, the concentration of the overall BPA contamination must be below the detection limit for BPA using the analytical system. Therefore, purified water for preparing the standard BPA solution must be filtered with a hydrophobic membrane to suppress BPA background levels of contamination. In addition, we investigated methods for effectively preserving environmental water containing BPA. The addition of a small amount of ethylenediaminetetraacetic acid (EDTA) provided good recovery even after overnight storage. By employing these precautionary measures and procedures to reduce BPA contamination from the analytical procedure, we could accurately determine l(-10) ppt of BPA in environmental water samples using a column switching HPLC system.     

Linear and Nonlinear Optical Properties Of Racemic (±)2-(α-Methylbenzylamino)-5-Nitropyridine Single Crystals

Linear and nonlinear optical properties of racemic (±)2-(α-methylbenzylamino)-5-nitropyridine ((±)MBANP) single crystals have been comprehensively investigated and compared with those of the enantiomorph (–)2-(α-methylbenzylamino)-5-nitropyridine ((–)MBANP) crystals. (±)MBANP crystal exhibits very high chemical and physical stability, but relatively small nonlinear optical coefficients (d₃₁ = 6.8 pm/V, d₃₂ = 4.7 pm/V, d₃₃ = 0.84 pm/V). A comparison between the nonlinear optical coefficients of (±)MBANP and (–)MBANP demonstrates the validity of the oriented-gas model in molecular crystals that neglects all the contributions from intermolecular interaction.     

Novel UV‐induced photografting process for preparing poly(tetrafluoroethylene)‐based proton‐conducting membranes

A novel process comprising the UV‐induced photografting of styrene into poly(tetrafluoroethylene) (PTFE) films and subsequent sulfonation has been developed for preparing proton‐conducting membranes. Although under UV irradiation the initial radicals were mainly generated on the surface of the PTFE films by the action of photosensitizers such as xanthone and benzoyl peroxide, the graft chains were readily propagated into the PTFE films. The sulfonation of the grafted films was performed in a chlorosulfonic acid solution. Fourier transform infrared and scanning electron microscopy were used to characterize the grafted and sulfonated membranes. With a view to use in fuel cells, the proton conductivity, water uptake, and mechanical properties of the prepared membranes were measured. Even through the degree of grafting was lower than 10%, the proton conductivity in the thickness direction of the newly prepared membranes could reach a value similar to that of a Nafion membrane. In comparison with γ‐ray radiation grafting, UV‐induced photografting is very simple and safe and is less damaging to the membranes because significant degradation of the PTFE main chains can be avoided. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 2624–2637, 2007     

In situ observations of domain wall motion in Mn–Zn and Ni–Zn ferrites by Lorentz microscopy and electron holography

Domain wall motion in Mn–Zn and Ni–Zn ferrites with applied magnetic fields is investigated by in situ observations with Lorentz microscopy and electron holography. It is found that both Mn–Zn and Ni–Zn ferrites have a mean grain size of approximately 10 μm and several pores with sizes ranging from 0.2 to 1.1 μm. In situ observations by Lorentz microscopy with an applied magnetic field reveals that in Mn–Zn ferrite, the domain walls move easily across the grain boundary, while in Ni–Zn ferrite, the domain walls move along the grain boundary but are pinned at the grain boundary and pores. From in situ observations of Ni–Zn ferrite by electron holography, it is clarified that domain wall pinning at the grain boundary retards a sensitive increase in magnetic flux parallel to the applied field direction, which is considered to result in high hysteresis loss.     

Temporal analysis of products (TAP) study on oxygen storage properties over Pt−Rh/CeO2 catalyst

The oxygen storage capacity of CeO₂, Ce_0.9Pr_0.1O₂, Pt?Rh/CeO₂ and Pt?Rh/Ce_0.9Pr_0.1O₂ was investigated by conventional GC pulse method and transient pulse techniques. It is shown that incorporation of PrO_y into CeO₂ matrix strongly promotes oxygen storage capacity (OSC) measured using the transient pulse technique. The improvement of OSC at low temperature is observed in Pt?Rh loaded onto CeO₂ and Ce?Pr catalysts.     

Design of a widely tunable laser with a chirped ladder filter

We theoretically investigated a digitally tunable laser with a chirped ladder filter and a ring resonator to obtain a wide wavelength tuning range covering the whole C- or L- band. The clear relation between the tuning range and laser structure, especially the ladder filter, is described analytically. The introduction of a chirped structure into a ladder filter is effective in achieving both wide tunability and a stable lasing mode. A numerical simulation based on multimode rate equations shows that a tuning range of over 40 nm and a mode suppression ratio over 40 dB can be achieved by introducing a chirped ladder filter.