Improvement in flow-sheet of extraction chromatography for trivalent minor actinides recovery

Journal of Radioanalytical and Nuclear Chemistry - Extraction chromatography flow-sheet employing octyl(phenyl)-N,N-diisobutylcarbonoylmethylphosphine oxide and bis(2-ethylhexyl) hydrogen phosphate...     

The required sample size in measuring oblique incidence absorption coefficient Experimental study

It is an important issue to clarify the minimum required size of a specimen for the accurate measurement of oblique incidence absorption coefficient. Investigation is made on the basis of experimental studies in a laboratory, using Aoshima's time stretched pulse technique. Measurements are carried out for glass fiber with thickness of 50 and 100 mm as highly absorbing materials and for ceramic with a thickness of 52 mm as relatively low absorbing material. The tested surface areas range from 0.0625 to 42 m² for glass fiber and from 0.1563 to 39.168 m² for ceramics. The absorption coefficients are determined at incidence angles from 0 to 45° in increments of 15°. With consideration of an active surface bounded by ellipse orbit, the minimum required surface area is 16 m² with a ratio of length to width of about 1.25. This value is twice the area size of the active surface, which is calculated from the geometry of source and microphone, and the width of the temporal window.     

Analysis of the manufacturing lead time in a production system with non-renewal batch input,threshold policy and post-operation

In this paper, we analyze the manufacturing lead time in a production system with BMAP (Batch Markovian Arrival process) input and post-operation operated under the N-policy. We use the factorization principle to derive the waiting time distribution (hence the manufacturing lead time) and the mean performance measures. A numerical example is provided.     

Development of Non-Halogen Flame Retardant Optical Fiber and Optical Fiber Cord

A non-halogen highly flame-retardant 0.9mm optical fiber and 2.0mm simplex optical cord, which are harmonized with the ecosystem, have been developed. The characteristics of them are presented in this paper.     

Anomalous PL brightening caused by partial Auger recombination of a (D, X) complex during an impact ionization avalanche in n-GaAs

Partial Auger recombination of the (D⁰, X) bound-exciton in n-GaAs at 4.2 K during an impact ionization avalanche under an applied pulse voltage has been investigated. The bright photoluminescence (PL)-pattern observed by applying the pulse voltage, characterizes well the formation of a current density filament. The observation of the bright PL spectra inside the current density filament gives a quite new result concerning the partial Auger recombination process of the (D⁰, X) complex, leaving the neutral donor in the excited states.     

Structure and reflective properties of Al-Cu-Fe quasicrystalline thin film prepared by laser induced arc method

Al-Cu-Fe thin films were prepared by laser induced arc (laser-arc) method from a single source—Al₆₃Cu₂₅Fe₁₂ alloy, which was proved to consist of quasicrystalline phase together with approximant phase. The composition of the deposited films meets the requirement for formation of icosahedral symmetry phase. Quasicrystalline phase was obtained after annealing the amorphous as-deposit film samples. The optical properties of the samples were investigated. Thin film samples of Al, Cu and Fe deposited under the same condition were employed for comparison. The results showed specific reflective properties of Al-Cu-Fe quasicrystal thin film in some wavelength range. The optical conductivity of the films exhibited a negative peak, centered about 440 nm in range of 190 to 800 nm. The Al-Cu-Fe quasicrystal thin films could absorb almost all the ray in the wavelength range from 420nm to 450 nm. The ratio of absorption was greater than 99%.     

Correlation between Al2O3 particles and interface of Al-Al2O3 coatings by cold spray

Al-Al₂O₃ composite coatings with different Al₂O₃ particle shapes were prepared on Si and Al substrate by cold spray. The powder compositions of metal (Al) and ceramic (Al₂O₃) having different sizes and agglomerations were varied into ratios of 10:1 wt% and 1:1 wt%. Al₂O₃ particles were successfully incorporated into the soft metal matrix of Al. It was found that crater formation between the coatings and substrate, which is typical characteristic signature of cold spray could be affected by initial starting Al₂O₃ particles. In addition, when the large hard particles of fused Al₂O₃ were employed, the deep and big craters were generated at the interface between coatings and hard substrates. In the case of pure soft metal coating such as Al on hard substrate, it is very hard to get proper adhesion due to lack of crater formation. Therefore, the composite coating would have certain advantages.     

Ethylene polymerization by chromium complexes with phosphorous‐bridged bisphenoxy ligand

Chromium catalysts combined with phosphorous‐bridged bisphenoxy ligands were found to be highly active for ethylene polymerization. The most efficient catalyst precursor among them, generated by combining bis[3‐tert‐butyl‐5‐methyl‐2‐hydroxyphenyl](phenyl)phosphine hydrochloride ( 1a ) and CrCl₃(THF)₃, was characterized. X‐ray analysis of (3‐tert‐butyl‐5‐methyl‐2‐phenoxy)(3‐tert‐butyl‐5‐methyl‐ 2‐hydroxyphenyl)(phenyl)phosphine bis(tetrahydrofuran)chromium dichloride ( 6 ), obtained by the reaction of 1a and CrCl₃(THF)₃ in the presence of NaH, revealed a unique structure in which one phenol moiety of the bisphenol did not coordinate to the chromium center. Complex 6 showed higher activities than those observed in the in situ catalyst system. Polyethylene of various molecular weights was obtained with differing activators. The highest activity (113.5 kg mmol (cat)^?1 h^?1) was observed when TIBA/TB was used as a cocatalyst. A medium molecular weight polymer with narrow molecular weight distribution (M_w = 128,700, M_w/M_n = 1.8) was obtained using a 6 ‐TIBA/B(C₆F₅)₃ system. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 3668–3676, 2007     

A short synthesis of 4-amino-3-hydroxybutyric acid (GABOB) via allyl cyanide

4-Amino-3-hydroxybutyric acid was synthesized from allyl cyanide in four steps in an overall yield of 38%. Ultrasonically promoted epoxidation of allyl cyanide with m-chloroperoxybenzoic acid giving oxiranylacetonitrile was used as a key step.     

First thermally responsive supramolecular polymer based on glycosylated amino acid

In materials science, a dynamic property sensitive to an environmental change (heat, light, electric current, pH, and other chemical or physical changes) is indispensable for intelligent materials. Such organic materials, however, are very limited even in conventional polymers. This paper clearly demonstrates that, regardless of the low molecular weight, a glycosylated amino acid derivative newly screened by a combinatorial method forms a macroscopic supramolecular hydrogel that reversibly swells or shrinks in response to the external temperature. Using the unique thermal response of the present hydrogel, we carried out the controlled release of DNA and the perfect removal of bisphenol A from the polluted water. Recently, advanced supramolecular polymers, in which monomers are noncovalently connected, are expected to be highly advantageous over traditional polymers because of their tunable and recyclable characteristics. The present result newly confers a dynamic feature on the supramolecular polymers, which is desirable for the sophisticated application in many fields.