Syntheses, characterization and study of the use of cobalt (II) Schiff-base complexes as catalysts for the oxidation of styrene by molecular oxygen

Schiff-Base complexes of bis-5-phenylazosalicylaldehyde ethylenediimine and bis-5-phenylazosalicylaldehyde-O-phenylenediimine ligands with Co(II) (I and II) have been synthesized and characterized by their IR spectra and elemental analyses. These complexes catalyze the oxidation of styrene in the presence of dioxygen and excess pyridine. The effect of the reaction conditions on the oxidation of styrene was studied by varying solvent, nature and amount of the catalyst and substrate. The catalytic behavior of the studied complexes was shown to be dependent on the conditions applied. In all reactions, acetophenone and 1- phenylethanol were the only observed products.     

Ab Initio Study of Conformational Properties of Heteroatom-Containing 1,2-Bisketene Analogues

Abstract

Minimum-energy and transition-state geometries of 4-oxobuta-1,3-diene-1-thione, buta-1,3-diene-1,4-dithione, 4-selenoxobuta-1,3-diene-1-thione, 4-selenoxobuta-1,3-diene-1-one, and buta-1,3-diene-1,4-diselenone were calculated using HF, B3LYP, and MP2 levels of theory and 6–31 + G* basis set by rotation around the related ?C?C? single bonds. In all of the above-mentioned molecules, the s-trans conformation was obtained as the most stable conformer with the 180° dihedral angle. In buta-1,3-diene-1,4-dithione, 4-selenoxobuta-1,3-diene-1-thione, and buta-1,3-diene-1,4-diselenone, the s-cis form of these compounds corresponded to the other energy-minimum geometry. Their skew geometries, with torsional angles approximately 100°, were a transition state for conformational interconversion between the two global minima forms. In 4-oxobuta-1,3-diene-1-thione and 4-selenoxobuta-1,3-diene-1-one, geometries with the C?C?C?C dihedral angles about 51 and 43° (respectively) were attributed to the second energy-minimum geometry. Transition-state structures from both molecules were found in the torsional angles at about 0 and 100°.

Supplemental materials are available for this article. Go to the publisher's online edition of Phosphorus, Sulfur, and Silicon and the Related Elements to view the free supplemental file.

GRAPHICAL ABSTRACT     

Adsorption of Metanil Yellow Azoic Dye from Aqueous Solution onto Mg‐Fe‐NO3 Layered Double Hydroxide

We report the preparation and characterization of a layered double hydroxide (LDH) adsorbent for azoic dye, metanil yellow (yellow GX; YGX) removal. The nanoparticles of Mg‐Fe‐LDH‐NO₃ adsorbent were prepared with Mg/Fe molar ratio of 3:1 by a hydrothermal process and coprecipitation method at pH 9.5 and were characterized by X‐ray powder diffraction (XRPD), thermal gravimetric analysis (TGA), elemental analysis, and Fourier transform infrared spectroscopy (FT‐IR). The size and morphology of nanoparticles were examined by scanning electron microscopy (SEM). The XRD patterns indicate that the intercalation of YGX between the LDH layers has not occurred and surface adsorption has happened. In the adsorption experiments, the Gibbs free energy ΔG⁰ values, the enthalpy ΔH⁰, and entropy ΔS⁰ was determined. The isotherms showed that the adsorption of YGX by Mg‐Fe‐LDH‐NO₃ was both consistent with Langmuir and Freundlich equations.     

Chemically bonded multiwalled carbon nanotubes as efficient material for solid phase extraction of some metal ions in food samples

Multiwalled carbon nanotubes chemically functionalized with 2-((3-silylpropylimino) methyl) phenol (SPIMP-MWCNT) and successfully applied for the solid phase extraction (SPE) of some metal ions in food samples. The influences of the analytical parameters including pH, amounts of solid phase, eluent conditions (type, volume and concentrations), sample volume and interference of some metal ions on the recoveries of ions Cu²⁺, Pb²⁺, Fe²⁺, Ni²⁺ and Zn²⁺ ion were investigated. The metal ions retained on SPIMP-MWCNT was eluted using 6?mL of 4?mol?L^?1 HNO₃ solution and their content was determined by flame atomic absorption spectrometry (FAAS) with recoveries more than 95% and relative standard deviations (n?=?5) between 2.4–3.4% for both reproducibility and repeatability. The detection limit of this metal ions was between 1.0–2.6?ng?mL^?1 (3S _b , n?=?10) and their preconcentration factor was 100, while their loading capacity was above 32.9?mg?g^?1 of SPIMP-MWCNT. The proposed method was successfully applied for the preconcentration and determination of analytes in different samples.     

The application of the gradient-based adjoint multi-point optimization of single and double shock control bumps for transonic airfoils

A shock control bump (SCB) is a flow control method that uses local small deformations in a flexible wing surface to considerably reduce the strength of shock waves and the resulting wave drag in transonic flows. Most of the reported research is devoted to optimization in a single flow condition. Here, we have used a multi-point adjoint optimization scheme to optimize shape and location of the SCB. Practically, this introduces transonic airfoils equipped with the SCB that are simultaneously optimized for different off-design transonic flight conditions. Here, we use this optimization algorithm to enhance and optimize the performance of SCBs in two benchmark airfoils, i.e., RAE-2822 and NACA-64-A010, over a wide range of off-design Mach numbers. All results are compared with the usual single-point optimization. We use numerical simulation of the turbulent viscous flow and a gradient-based adjoint algorithm to find the optimum location and shape of the SCB. We show that the application of SCBs may increase the aerodynamic performance of an RAE-2822 airfoil by 21.9 and by 22.8 % for a NACA-64-A010 airfoil compared to the no-bump design in a particular flight condition. We have also investigated the simultaneous usage of two bumps for the upper and the lower surfaces of the airfoil. This has resulted in a 26.1 % improvement for the RAE-2822 compared to the clean airfoil in one flight condition.     

The Multi-point Optimization of Shock Control Bump with Constant-Lift Constraint Enhanced with Suction and Blowing for a Supercritical Airfoil

Both shock control bump (SCB) and suction and blowing are flow control methods used to control the shock wave/boundary layer interaction (SWBLI) in order to reduce the resulting wave drag in transonic flows. A SCB uses a small local surface deformation to reduce the shock-wave strength, while suction decreases the boundary-layer thickness and blowing delays the flow separation. Here a multi-point optimization method under a constant-lift-coefficient constraint is used to find the optimum design of SCB and suction and blowing. These flow control methods are used separately or together on a RAE-2822 supercritical airfoil for a wide range of off-design transonic Mach numbers. The RANS flow equations are solved using Roe’s averages scheme and a gradient-based adjoint algorithm is used to find the optimum location and shape of all devices. It is shown that the simultaneous application of blowing and SCB (hybrid blowing/SCB) improves the average aerodynamic efficiency at off-design conditions by 18.2 % in comparison with the clean airfoil, while this increase is only 16.9 % for the hybrid suction/SCB. We have also studied the SWBLI and how the optimization algorithm makes the flow wave structure and interactions of the shock wave with the boundary layer favorable.     

Fabrication of modified TiO2 nanoparticle carbon paste electrode for simultaneous determination of dopamine, uric acid, and l-cysteine

A carbon paste electrode, modified with 2, 2′-[1,7-hepthandiylbis(nitriloethylidyne)]-bis-hydroquinone and TiO₂ nanoparticles, was used for the simultaneous determination of dopamine (DA), uric acid (UA), and l-cysteine. The study was carried out by using cyclic voltammetry, chronoamperometry, and square wave voltammetry (SWV) techniques. Some kinetic parameters such as the electron transfer coefficient (α) and heterogeneous rate constant (k_s) were also determined for the DA oxidation. A dynamic range of 8.0–1400 μM, with the detection limit of 8.4 × 10⁻⁷ M for DA, was obtained using SWV (pH = 7.0). The prepared electrode was successfully applied for the determination of DA, UA, and l-cysteine in real samples.     

Syntheses and mesomorphic properties of new oxygen-bridged dicopper complex homologous derived from azo-containing salicylaldimine Schiff base ligands

The synthesis, characterization and liquid crystal properties of a homologous series of new tridentate 5-((4-ⁿalkoxyphenyl) azo)-N-(3-ydroxypropyl) salicylaldimine ligands (alkoxy = octloxy, decyloxy, dodecyloxy and tetradecyloxy) and their dicopper(II) complexes are reported. These ligands were prepared by the condensation of the 5-((4-ⁿalkoxyphenyl)azo)salicylaldehydes homologous with 3-amino-1-propanol. The ligands and their dicopper complexes have been characterized by IR, ¹H NMR, mass spectroscopy and elemental analyzes. The liquid crystalline properties of the ligands and the related dicopper complexes were studied by differential scanning calorimetry (DSC) and by using a polarizing microscope equipped with a heating and cooling stage. None of the free ligands exhibit liquid crystalline behavior but all of the dicopper complexes demonstrate a smectic A mesophase.