New 7‐membered diazepanone alkoxyamines for nitroxide‐mediated radical polymerization

The synthesis of new 7‐membered diazepanone alkoxyamines [2,2,7,7‐tetramethyl‐1‐(1‐phenyl‐ethoxy)‐[1,4]diazepan‐5‐one ( 3 ) and 2,7‐diethyl‐2,3,7‐trimethyl‐1‐(1‐phenyl‐ethoxy)‐[1,4]diazepan‐5‐one ( 8 )] through the Beckmann rearrangement of piperidin‐4‐one alkoxyamines was developed. Both 3 and 8 were evaluated as initiators and regulators for the nitroxide‐mediated radical polymerization of styrene and n‐butyl acrylate. 8 , a sterically highly hindered alkoxyamine readily available as a crystalline solid, allowed the fast and controlled polymerization and preparation of polymers with low polydispersity indices (1.2–1.4) up to a degree of polymerization of about 100. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 3332–3341, 2004     

Multicyclic polyethers derived from 1,1,1‐tris(4‐hydroxyphenyl)ethane and 2,6‐dihalopyridines

Poly(pyridine ether)s were prepared in two ways: the polycondensation of silylated 1,1,1‐tris(4‐hydroxyphenyl)ethane (THPE) with 2,6‐difluoropyridine (method A) and the polycondensation of free THPE with 2,6‐dichloropyridine (method B). With method A, the THPE/difluoropyridine feed ratio was varied from 1.0:1.0 to 1.0:1.6. Cycles, bicycles, and multicycles were the main reaction products, and crosslinking was never observed. When ideal stoichiometry was used exclusively, multicycles free of functional groups were obtained. These multicycles were detectable in matrix‐assisted laser desorption/ionization time‐of‐flight (MALDI‐TOF) mass spectra up to B₃₈C₇₆ with a mass of approximately 32,000 Da. With method B, the reaction conditions were varied at a fixed feed ratio to achieve an optimum for the preparation of multicyclic polyethers, but because of the lower reactivity of 2,6‐dichloropyridine, a quantitative conversion was not achieved. The reaction products were characterized with MALDI‐TOF mass spectrometry, viscosity measurements, and size exclusion chromatography. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5725–5735, 2004     

Differential scanning calorimetry and thermogravimetric analysis investigation of the thermal properties and degradation of some radiation‐grafted films and membranes

The influence of irradiation and grafting on the crystallinity of three base polymers has been investigated with differential scanning calorimetry. Grafting has the largest effect on the base polymer crystallinity and results in a reduction of the crystallinity. The thermal degradation of the base polymers and grafted films has been investigated with thermogravimetric analysis. The extent of the fluorination of the base polymer, the irradiation method, and the graft level all influence the thermal degradation and its activation energy. It is proposed that the variation of the chain lengths of the grafted polystyrene chains is actually a primary underlying factor responsible for the influence of these various parameters on the degradation process. The first results of a comparative thermal analysis of some fuel‐cell membranes are also presented, and the promise and shortcomings of this method are discussed. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2612–2624, 2004     

Quantitative electron probe microanalysis for the characterization of thin carbon-boron layers in fusion devices

Summary The first wall of the fusion device TEXTOR at the Forschungszentrum Jülich has been coated in situ with an amorphous hydrogen rich carbon/boron film (a-C/B:H) which reduces plasma impurities caused by the plasma surface interaction. The results of the coating process of the 35 m² large inner wall surface have been controlled by a recently developed modification of the quantitative electron probe microanalysis, which has been applied to 12 samples from specified positions inside the tokamak. The quantification itself is based on a Monte Carlo simulation of electron trajectories providing very accurate results for X-ray intensities emitted by elements present in the electron bombarded sample. The Monte Carlo results are used in the present work to calibrate the measured X-ray intensities emitted by boron and carbon from the a-C/B:H layers deposited on pure silicon substrates. As a result the total deposited mass of the layer per area unit as well as the composition of the layers (except hydrogen) could be determined very accurately. The relative errors were less than 7%. The limit of detectability were found to be in the range of one monolayer for boron as well as for carbon.     

Butyltins in california river and lake marina waters

Butyltins were analyzed in waters from California river and lake marinas and were detected at the part per trillion (ppt) level in most locations. The tributyltin:dibutyltin (TBT/DBT) ratios in the fresh waters were similar to those in their saline counterparts indicating like rates of degradation in the two salinity regimes.     

Development of a parallel storm surge model

A new parallel storm surge model, the Parallel Environmental Model (PEM), is developed and tested by comparisons with analytic solutions. The PEM is a 2‐D vertically averaged, wetting and drying numerical model and can be operated in explicit, semi‐implicit and fully implicit modes. In the implicit mode, the propagation, Coriolis and bottom friction terms can all be treated implicitly. The advection and diffusion terms are solved with a parallel Eulerian–Lagrangian scheme developed for this study. The model is developed specifically for use on parallel computer systems and will function accordingly in either explicit of implicit modes. Storm boundary conditions are based on a simple exponential decay of pressure from the centre of a storm. The simulated flooding caused by a major Category 5 hurricane making landfall in the Indian River Lagoon, Florida is then presented as an example application of the PEM. Copyright © 2003 John Wiley & Sons, Ltd.     

Standardization of Methods for Characterizing the Surface Geometry of Solids

Since a comprehensive survey published in 1999 [1] much work was done in standardizing measuring methods to characterize the surface geometry of dispersed and/or porous solids and to certify reference materials. The present paper is an extension of a short communication [2]. It gives a survey on existing standards and reports on new drafts and proposals.