Effect of Fe substitution on the thermal expansion of the highT c superconductor Y1Ba2Cu3O y

Thermal expansion measurements have been carried out on Fe substituted superconducting compounds Y₁Ba₂(Cu_1−x Fe _x )₃O _y (0<x<4%) using a high resolution dilatometer employing the three terminal capacitance technique. The experimental set up is sensitive enough to detect changes in α of less than 10⁻⁸K⁻¹. Results show that the jump Δα in the coefficient of linear thermal expansion at the superconducting transition temperature,T _c, increases almost linearly with Fe concentration. The normal state thermal expansion coefficient α first decreases, attains a minimum value aroundx=1% and then increases for higher Fe concentrations. The oxygen content per unit formula is almost constant up tox=1% and then increases rapidly withx. It has also been observed that the anomalous behaviour of α around 260 K observed by Meingastet al [22] for Fe concentrationx=5% is due to inadequate annealing of the sample.     

Response Factor Correction for Estimation of Ester Content in Biodiesel

EN 14103 is generally used for quantification of ester content in biodiesel free of heptadecanoate ester (C17:0) or methyl nonadecanoate (C19:0), which are employed as internal standards. It was observed that ester content obtained by EN 14103 method did not match with theoretical value of biodiesel, as the method did not take care of response factors of each component to compensate for changes in detector sensitivities. In this study, the whole range of fatty acid (C₆–C_24:1) methyl esters have been taken into consideration for the calculation of the ester content. Methyl nonadecanoate (C19:0) was used as an internal standard. The response factors of both the saturated and unsaturated methyl esters in the range C₆–C_24:1 were estimated and found in the range 0.97–1.16. The ester content was calculated after applying the response factors of each methyl ester. The results obtained by this method agreed well with the theoretical value as compared to estimated value using EN14103 method. The results obtained from this method also show good correlation (R ² = 0.98) with ¹H-NMR method. Further, this method does not depend on nature of biodiesel feed stock and is applicable to all methyl biodiesel samples obtained from different raw materials.     

Anisotropy of penetration depth in superconducting tin

Microwave resonance technique at 3000 MHz has been used to carry out measurements of the temperature variation of penetration depth in single crystals of pure tin. Several samples of known crystallographic orientations have been studied, and the anisotropy of penetration depth obtained. The results clearly show non-tensorial anisotropy of penetration depth, and hence provide a direct experimental evidence for non-local relation between the current density and associated magnetic field in a type I superconductor.     

Estimation of Olefin Dimerisation Products by GC/GC–MS and IR Techniques

A GC and IR based protocol was developed for monitoring the isobutene dimerisation process wherein the complete characterisation of the products was carried out by GC coupled with mass spectrometry. In the dimerisation process, LPG from FCC process comprising a mixture of saturated and unsaturated C4 hydrocarbons is subjected to a dimerisation process using a catalyst to produce C8 hydrocarbons. The reaction is carried out keeping in view the demand for high-octane blending components in gasoline. The isooctene generated in the process (mainly from the dimerisation of isobutene) is converted into isooctane having the RON and MON value 100. The monitoring process requires the use of two different column chemistries, viz., a 100 m CPSIL PONA CB non-polar column for C8 and its isomers and an Alumina PLOT column for C4 hydrocarbons. A 100 m non-polar column does not separate the C4 mixture since the column is meant for gasoline range products containing C5 and above hydrocarbons. Therefore, a need was felt for an improvised method which can handle both the analyses simultaneously. A cryogenic oven program starting from 0 °C was developed for separating the isomers of C4 hydrocarbons and C8 hydrocarbons on a single column during the single run by Detailed Hydrocarbon Analyzer. The data obtained using the cryo programme was validated with data obtained using Alumina PLOT column on C4 mixture since the Alumina PLOT column is the widely accepted column chemistry for separating the C4 hydrocarbons. An IR method for the estimation of the total olefin content was developed using 2,2,4-trimethyl pentene-1 as the reference standard. The total olefins generated during the process were identified by GC–MS, quantified by DHA-FID and validated by infrared spectroscopy. A good correlation was found between GC and IR spectral results (correlation coefficient R ²  = 0.99).     

Paraconductivity of Ge-covered tin films,II

The temperature dependence if the excess electrical conductivity of thin superconducting tin films (a) covered by a protective germanium layer and (b) sandwiched between two germanium layers above the transition temperature has been measured. These thin films have been deposited on glass substrates held at room temperature. It was found that the pair- breaking parameter δ for germanium covered tin filns varies exponentially with normal state sheet resistance R^□_N and could be represented by δ = 3.77×10^-4 exp (1.76R^□_N) in the range 0.28?R^□_N<1.6ohm/?. Higher R^?_N samples show close agreement with Aslamazov-Larkin expression. Information obtained from type (b) samples showed that although protective germanium layer increases the δ values, sandwich type structure lowers it significantly. Results show that such a strong dependence of δ could be related to changes in the Cooper pair relaxation time and the proximity effect.     

Fractals in one and two dimensions of medium energy particles in 800 GeV p-AgBr interactions

We present the first experimental results on self-similar nature of fluctuations of one and two-dimensional density distributions of medium energy particles in 800 GeV p-AgBr interactions. The density fluctuations as measured by 1?D _q are found to be more in two dimensions as compared to those in one dimension, whereas the fluctuations decrease with increase in multiplicity. It has been found that the self-similar cascade model with multifractal properties describes well the observed fluctuations. The ratios of multifractal power law indices are found to be independent of the dimensionality of phase space and of multiplicity.     

Detailed Hydrocarbon Class Composition Analysis and Trace Level BTEX Estimation in Raffinate Column Bottom (RCB) Using GC×GC–TOFMS

A two-dimensional gas chromatography coupled with time-of-flight mass spectrometry (GC×GC–TOFMS) method was developed for the hydrocarbon class composition analysis and benzene, toluene, ethylbenzene, and xylene (BTEX) estimation of raffinate column bottom (RCB), which is generated as a by-product from linear alkyl benzene (LAB) plants. The molecular level characterization of RCB is important to generate value-added products for the petrochemical industry. GC×GC–TOFMS was found to be an excellent tool for estimation of hydrocarbon class composition (paraffins, naphthenes, monoaromatics, diaromatics, and polyaromatic hydrocarbons) and trace level BTEX in a single run. The hydrocarbon class composition was validated with the standard method based on HPLC (ASTM D6591) and good correlation was obtained. Finally, RCB is anticipated to be a useful nonhazardous safe by-product which could be used further for generating added value.     

Determination of Fatty Acid Based Lubricity Improver in Diesel by GC

GC/FID has been used for the determination of a fatty acid based lubricity improver in diesel fuel. The method makes use of phase transfer catalysis for the enrichment of the lubricity improver from the diesel matrix. The use of phase transfer catalysis for the simultaneous extraction, preconcentration and derivatisation of the fatty acids enables determination of concentrations of 20 mg L^?1. The method has been successfully applied to the analysis of diesel streams from various sources. The effect of the diesel matrix has also been investigated and it does not affect the recovery of the additive.     

Estimation of Olefin Dimerisation Products by GC/GC–MS and IR Techniques

A GC and IR based protocol was developed for monitoring the isobutene dimerisation process wherein the complete characterisation of the products was carried out by GC coupled with mass spectrometry. In the dimerisation process, LPG from FCC process comprising a mixture of saturated and unsaturated C4 hydrocarbons is subjected to a dimerisation process using a catalyst to produce C8 hydrocarbons. The reaction is carried out keeping in view the demand for high-octane blending components in gasoline. The isooctene generated in the process (mainly from the dimerisation of isobutene) is converted into isooctane having the RON and MON value 100. The monitoring process requires the use of two different column chemistries, viz., a 100 m CPSIL PONA CB non-polar column for C8 and its isomers and an Alumina PLOT column for C4 hydrocarbons. A 100 m non-polar column does not separate the C4 mixture since the column is meant for gasoline range products containing C5 and above hydrocarbons. Therefore, a need was felt for an improvised method which can handle both the analyses simultaneously. A cryogenic oven program starting from 0 °C was developed for separating the isomers of C4 hydrocarbons and C8 hydrocarbons on a single column during the single run by Detailed Hydrocarbon Analyzer. The data obtained using the cryo programme was validated with data obtained using Alumina PLOT column on C4 mixture since the Alumina PLOT column is the widely accepted column chemistry for separating the C4 hydrocarbons. An IR method for the estimation of the total olefin content was developed using 2,2,4-trimethyl pentene-1 as the reference standard. The total olefins generated during the process were identified by GC–MS, quantified by DHA-FID and validated by infrared spectroscopy. A good correlation was found between GC and IR spectral results (correlation coefficient R ² = 0.99).