Modulation of the phase difference between polarization modes in single-mode fibers

Mechanisms of polarization modulation in a single-mode fiber that modulate the phase difference between polarization modes without affecting their amplitudes are considered. A coefficient that characterizes the efficiency of cylindrical piezoceramic modulators and is independent of their resonant properties is introduced. Analytical expressions for this coefficient for different modulation mechanisms are derived. The lateral pressure on the fiber is shown to provide the highest efficiency. For isotropic fibers, a modulator with a squeezing covering, which increases significantly its efficiency, is studied. For anisotropic fibers, the most appropriate way of phase difference modulation is longitudinal extension, in which case the birefringence axes do not have to be matched. In most cases, the measured and predicted efficiencies are in good correspondence.     

On the stability of retrial queues

We consider the following Type of problems. Calls arrive at a queue of capacity K (which is called the primary queue), and attempt to get served by a single server. If upon arrival, the queue is full and the server is busy, the new arriving call moves into an infinite capacity orbit, from which it makes new attempts to reach the primary queue, until it finds it non-full (or it finds the server idle). If the queue is not full upon arrival, then the call (customer) waits in line, and will be served according to the FIFO order. If λ is the arrival rate (average number per time unit) of calls and μ is one over the expected service time in the facility, it is well known that μ > λ is not always sufficient for stability. The aim of this paper is to provide general conditions under which it is a sufficient condition. In particular, (i) we derive conditions for Harris ergodicity and obtain bounds for the rate of convergence to the steady state and large deviations results, in the case that the inter-arrival times, retrial times and service times are independent i.i.d. sequences and the retrial times are exponentially distributed; (ii) we establish conditions for strong coupling convergence to a stationary regime when either service times are general stationary ergodic (no independence assumption), and inter-arrival and retrial times are i.i.d. exponentially distributed; or when inter-arrival times are general stationary ergodic, and service and retrial times are i.i.d. exponentially distributed; (iii) we obtain conditions for the existence of uniform exponential bounds of the queue length process under some rather broad conditions on the retrial process. We finally present conditions for boundedness in distribution for the case of nonpatient (or non persistent) customers. This revised version was published online in June 2006 with corrections to the Cover Date.     

Production of Semiconducting III–V Single Crystals: Current Status and Outlook

The current status of and outlook for the worldwide production of semiconducting III–V single crystals, primarily gallium arsenide, are examined. Particular emphasis is placed on improving production technologies and reaching head positions in the vertical crystallization technology.     

Identification of dislocations and their influence on the recombination of charge carriers in gallium nitride

The relation between the density of etch pits revealed in GaN by etching in a KOH/NaOH eutectic and the density of dislocations determined by transmission electron microscopy (TEM) is studied along with the relation between the density of dislocations and the density of dark spot defects observed in GaN by microcathodoluminescence (MCL) and electron-beam-induced current (EBIC). It is demonstrated that selective etching is a reliable rapid method for the determination of the type and density of dislocations in GaN in the range 10⁶–10⁸ cm^?2, while MCL and EBIC can be used for the rapid nondestructive determination of the density of dislocations in the range 10⁶–10⁸ cm^?2. It is also found that some deep electron and hole traps are related to dislocations.     

Stochastic Arithmetic: s-spaces and Some Applications

It has been recently shown that computation with stochastic numbers as regard to addition and multiplication by scalars can be reduced to computation in familiar vector spaces. In this work we show how this can be used for the algebraic solution of linear systems of equations with stochastic right-hand sides. On several examples we compare the algebraic solution with the simulated solution using the CADNA package.