Wavelength and power monitoring of DWDM systems using scanning F–P filter calibrated with a F–P laser

A novel technique to overcome the long-term drift and hysteresis of a scanning Fabry–Perot filter was developed and applied to wavelength and power monitoring of DWDM system. By using the comb peaks generated by a temperature-stabilized, near threshold-biased Fabry–Perot diode laser as wavelength reference for the scanning Fabry–Perot filter, wavelength and power measurement accuracy of better than ±10 pm and 0.2 dB, respectively, were achieved.     

THE -PROBLEM FOR HOLOMORPHIC (0,2)-FORMS ON PSEUDOCONVEX DOMAINS IN SEPARABLE HILBERT SPACES AND D.F.N. SPACES

51. IntroductionL. H5.m.nd..l3] solved the 0problem by using the L2-estimates for partial differentialoperators in C'.. J. Kajiwara[4] studied infinite dimensional generalizations of the poten-tial kernel. Concerning the 0-problem in infinite dimensional spaces, P. ffeb.i.lll] investi-gated the a-equation for coc (o, 1)-forms in arbitrary pseudoconvex open subsets of separableHilbert spaces without growth condition. J. F. Colombeau and B. Perr.t[l1 showed that aCoc solution u of 0u = w ca…     

Active long pulse shaping technique of pulsed CO2 laser using multi-pulse discharge control

We describe the pulse forming of pulsed CO₂ laser using multi-pulse superposition technique. Various pulse shapes, high duty cycle pulse forming network (PFN) are constructed by time sequence. This study shows a technology that makes it possible to make various long pulse shapes by activating SCRs of three PFN modules consecutively at a desirable delay time with the aid of a PIC one-chip microprocessor. The power supply for this experiment consists of three PFN modules. Each PFN module uses a capacitor, a pulse forming inductor, a SCR, a high voltage pulse transformer, and a bridge rectifier on each transformer secondary. The PFN modules operate at low voltage by driving the primary of HV pulse transformer. The secondary of the transformer has a full-wave rectifier, which passes the pulse energy to the load in a continuous sequence.We investigated various long pulse shapes as different trigger time intervals of SCRs among three PFN modules. As a result, we could obtain laser beam with various pulse shapes and durations from about 250 to 1000 μs.     

ON THE ACOUSTIC ABSORPTION OF MULTI-LAYER ABSORBERS WITH DIFFERENT INNER STRUCTURES

A rigorous finite element analysis procedure is developed to study the effect of the inner structures on the acoustic absorption of multi-layer absorbers. To do this, four types of basic inner structure compartments adopted in the multi-layer absorbers are selected for analysis. These compartments are composed of porous materials inlaid with perforated plates of various shapes, say, triangle, semicircle, convex rectangle and plate shapes. As it is different from the conventional finite element analysis for the acoustic system in the literature, the perforated plates are simulated by appropriate equivalent boundary conditions, depending on their thickness, hole radius, hole pitch and porosity and the air contained in the holes. A large number of total degrees of freedom generated from meshing the air in the holes of perforated plates are thus avoided. The results reveal that the inner structures of the multi-layer absorbers will influence the acoustic absorption at some frequency bands significantly. Based on those features, the multi-layer absorber with a novel inner structure is then designed and manufactured. Both the finite element and experimental results show that its acoustic absorption would be distinctly promoted.     

聚丙烯醇做土壤改良剂研究：老化与作用力分析

聚烯醇可生物分解且无毒性，可做为土壤改良剂。其在土壤中受温度、紫外线影响而老化的问题为本研究的一部份。以加热及UV处理PVA膜与PVA与SiO2混合物。样品以FT-IR光谱了解其劣化情况。PVA膜与土壤之作用力则以原子力显微镜量测其力曲线与观察表面变化。此外PVA与SiO2混合物则以SEM观察其受热与受UV处理的结果。     

The glow curve structure for the LiF:Mg,Cu,Na,Si TL detector with dopants concentrations and sintering temperatures

The glow curve structures for LiF:Mg,Cu,Na,Si TL detectors with various dopant concentrations and sintering temperatures were investigated for the improvement of the glow curve structure and sensitivity of the TL detector. The dopant concentrations were varied over the following ranges: Mg (0–0.25 mol%), Cu (0–0.07 mol%), Na and Si (0–1.5 mol%). With increasing Cu concentration, the intensity of the main peak was intensified and reached a maximum at a concentration of 0.05 mol%. The high-temperature peak was reduced. The dependency of the main peak intensity on the Mg concentration exhibits a sharp maximum at 0.2 mol%. The intensity of the high-temperature peak tends to rise slightly with increasing Mg concentration. It was found that the optimum concentrations of the dopants in the LiF:Mg,Cu,Na,Si TL material are Mg: 0.2 mol%, Cu: 0.05 mol%, Na and Si: 0.9 mol%. The dependency of the main peak intensity on sintering temperature exhibits a very sharp maximum at 830°C. The high-temperature peak was rapidly reduced after 825°C.     

Pressure and temperature dependence of the gas‐transport properties of dense poly[2,6‐toluene‐2,2‐bis(3,4‐dicarboxylphenyl)hexafluoropropane diimide] membranes

The gas‐transport properties of poly[2,6‐toluene‐2,2‐bis(3,4‐dicarboxylphenyl)hexafluoropropane diimide] (6FDA‐2,6‐DAT) have been investigated. The sorption behavior of dense 6FDA‐2,6‐DAT membranes is well described by the dual‐mode sorption model and has certain relationships with the critical temperatures of the penetrants. The solubility coefficient decreases with an increase in either the pressure or temperature. The temperature dependence of the diffusivity coefficient increases with an increase in the penetrant size, as the order of the activation energy for the diffusion jump is CH₄ > N₂ > O₂ > CO₂. Also, the average diffusion coefficient increases with increasing pressure for all the gases tested. As a combined contribution from sorption and diffusion, permeability decreases with increases in the pressure and the kinetic diameter of the penetrant molecules. Even up to 32.7 atm, no plasticization phenomenon can be observed on flat dense 6FDA‐2,6‐DAT membranes from their permeability–pressure curves. However, just as for other gases, the absolute value of the heat of sorption of CO₂ decreases with increasing pressure at a low‐pressure range, but the trend changes when the feed pressure is greater than 10 atm. This implies that CO₂‐induced plasticization may occur and reduce the positive enthalpy required to create a site into which a penetrant can be sorbed. Therefore, a better diagnosis of the inherent threshold pressure for the plasticization of a glassy polymer membrane may involve examining the absolute value of the heat of sorption as a function of pressure and identifying the turning point at which the gradient of the absolute value of the heat of sorption against pressure turns from a negative value to a positive one. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 354–364, 2004