Thin-gate oxides prepared by pure water anodization followed byrapid thermal densification

Anodic oxidation at room temperature with pure deionized water as electrolyte and then followed by high-temperature rapid thermal densification was used to prepare high breakdown endurance thin-gate oxides with thicknesses of about 50 Å. It was observed that the oxides prepared by anodic oxidation followed by rapid thermal densification (AOD) show better electrical characteristics than those grown by rapid thermal oxidation (RTO) only. The AOD oxides have a very low midgap interface trap density, Ditm, of smaller than 1×10¹⁰ eV^-1 cm^-2 and negative effective oxide trapped charge. From the smaller leakage currents observed during staircase ramp voltage time-zero dielectric breakdown (TZDB) and constant field time-dependent dielectric breakdown (TDDB) testings, it is supposed that the uniform interfacial property and the pretrapped negative charges in AOD oxides are responsible for the improved characteristics     

Effect of epitaxial realignment on the leakage behavior of arsenic-implanted,as-deposited polycrystalline Si-on-single crystal Si diodes

When dopants are indiffused from a heavily implanted polycrystalline silicon film deposited on a silicon substrate, high thermal budget annealing can cause the interfacial “native” oxide at the polycrystalline silicon-single crystal silicon interface to break up into oxide clusters, causing epitaxial realignment of the polycrystalline silicon layer with respect to the silicon substrate. Anomalous transient enhanced diffusion occurs during epitaxial realignment and this has adverse effects on the leakage characteristics of the shallow junctions formed in the silicon substrate using this technique. The degradation in the leakage current is mainly due to increased generation-recombination in the depletion region because of defect injection from the interface.     

Practical stopping criteria for validating safety-critical software by estimating impartial reliability

In this research, we investigate stopping rules for software testing and propose two stopping rules from the aspect of software reliability testing based on the impartial reliability model. The impartial reliability difference (IRD-MP) rule considers the difference between the impartial transition-probability reliabilities estimated for both software developer and consumers at their predetermined prior information levels. The empirical–impartial reliability difference (EIRD-MP) rule suggests stopping a software test when the computed empirical transition reliability is tending to its estimated impartial transition reliability. To insure the high-standard requirement for safety-critical software, both rules take the maximum probability (MP) of untested paths into account.     

The base current degradation of poly-emitter BJTs under AC stress

A simple model for the analysis of the ac stress effect in poly-emitter bipolar transistors is presented. Apart from the reverse-bias induced hot-carrier effects, the forward-bias recovery effect is a key factor under ac stress, it obviously suppresses the base current degradation of the device which is caused during the reverse-bias periods. In this work, we derived the relationship between the excess base current and the stress time for different ac stress conditions. This model is verified with experimental results.<>     

Size of Micelles Determined by Static Fluorescence Quenching

We developed a new method to measure the average aggregation number of large rod-like micelles using static fluorescence self-quenching of a solubilized fluorophore. The method is based on the increase of self-quenching of micelle-solubilized pyrene through excimer formation. We consider the effect of random distribution of pyrene in micelles and the micellar size distribution. The measured average aggregation <n> _M is based on a new M-weighted raging similar to our exponential-weighted averaging in the transient decay method. We apply this method to study the effect of a large concentration of salt on the average aggregation behavior of sodium dodecyl sulfate (SDS) and cetyle tetraammonium bromide (CTAB). The sizes increase with increasing ionic concentrations. For SDS, we used the thermodynamic model developed by Missel et al. to calculate < n > _M which we compare with experimental results.     

Temporal Response of SERS to the Potential for 4-Cyanopyridine Adsorbed on Ag Electrode

Time-resolved surface-enhanced Raman scattering (SERS) was applied to study the response of Raman bands from 4-cyanopyridine (PyCN) adsorbed on a Ag electrode to variation of the potential; the temporal resolution was 0.1 s. The response of the SERS signals of PyCN was instantaneous to the oxidation potential of Ag electrode. However, delay of the SERS signals was observed while AgCl was reducing. The decay and growth of the SERS bands look place within 1 s in the cases of desorption and adsorption of PyCN on the electrode. It took much longer for PyCN to alter from one adsorption geometry to another on the electrode.     

Optically clear simultaneous interpenetrating polymer networks based on poly(ethylene glycol) diacrylate and epoxy. I. Preparation and characterization

Poly(ethylene glycol) diacrylate was synthesized from poly(ethylene glycol) of molecular weight 600 with acryloyl chloride in a molar ratio of 1:2. Poly(ethylene glycol) diacrylate (PEGDA) was then blended with diglycidyl ether of bisphenol A (DGEBA) in various ratios, followed by curing with 2,2′-azobisisobutyronitrile (AIBN) and isophronediamine (IPDA) simultaneously. Viscosity changes before and during IPN formation were examined with a Brookfield viscometer. Formation of H-bonding and functional group changes were investigated with FTIR. Exothermic curing thermograms were recorded with dynamic DSC. Optically clear IPNs thus obtained were characterized with rheometric dynamic spectroscopy (RDS) and scanning electron microscopy (SEM) to check possible compatibility of the two networks. Experimental results revealed that during IPN formation hydrogen bonds between PEGDA and DGEBA and interlock of networks had profound effect on viscosity change and pot-life. Complete compatibility of the IPNs was found as DGEBA content was higher than 50% by weight. The compatibility between PEGDA and DGEBA networks was evidenced from inner shift of a single damping peak in RDS. In the meantime, SEM micrographs confirmed the coincidence with the result of RDS © 1992 John Wiley &Sons, Inc.     

Voltammetric study of copper(I) thioacetamide complexes

Summary The composition and stability of copper(I) complexes with thioacetamide (TAA) have been evaluated with the help of square-wave voltammetry using the fast pulse technique. Two species, namely Cu(I) (TAA) and Cu(I) (TAA)₂, have been identified having the formation constants log ₁=16.85; log ₂=18.03. The complex is stable in highly acidic medium (pH1). The application for the determination of copper is pointed out.     

Optically clear simulataneous interpenetrating polymer networks based on poly(ethylene glycol) diacrylate and epoxy. II. Kinetic study

Simultaneous interpenetrating polymer networks (SINs) based on diglycidyl ether of bis-phenol A (DGEBA) and poly(ethylene glycol) diacrylate (PEGDA) in weight ratios of 100/0, 50/50, and 0/100 were blended and cured simultaneously by using benzoyl peroxide (BPO) and m-xylenediamine (MXDA) as curing agents. A kinetic study during SIN formation was carried out at 45, 55, 63, and 70°C. Concentration changes for both the epoxide and C?C bond were monitored with FTIR. A rate expression for DGEBA cure kinetics was established with a model reaction of phenyl glycidyl ether (PGE) and benzylamine. Experimental results revealed that lower rate constants and higher activation energy for the SIN were found, compared with those for the constituent DGEBA and PEGDA network formation. A model of network interlock was proposed to account for this phenomenon. During simultaneous cure of DGEBA and PEGDA, the interlock (mutual entanglement) between DGEBA and PEGDA networks provided a sterically hindered environment, which subsequently increased the activation energy and reduced cure rates for both DGEBA and PEGDA. © 1993 John Wiley & Sons, Inc.     

Molecular-dynamics studies of bending mechanical properties of empty and C60-filled carbon nanotubes under nanoindentation

This paper utilizes molecular-dynamics simulations to investigate the mechanical characteristics of a suspended (10, 10) single-walled carbon nanotube (SWCNT) during atomic force microscopy (AFM) nanoindentation at different temperatures. Spontaneous topological transition of the Stone-Wales (SW) defects is clearly observed in the indentation process. The present results indicate that under AFM-bending deformation, the mechanical properties of the SWCNT, e.g., the bending strength, are dependent on the wrapping angle. In addition, it is also found that the radial dependence of the reduced formation energy of the SW defects is reasonably insensitive only for the small tubes. However, for tube diameters greater than 2.4 nm [corresponding to the (18, 18) CNT], the SW defects tend to be more radius sensitive. The results indicate that the bending strength decreases significantly with increasing temperature. This study also investigates the variation in the mechanical properties of the nanotube with the density of C60 encapsulated within the nanotube at various temperatures. It is found that, at lower temperatures, the bending strength of the C60-filled nanotube increases with C60 density. However, the reverse tendency is observed at higher temperatures. Finally, the "sharpest tip" phenomena between the probe and the tube wall and the elastic recovery of the nanotube during the retraction process are also investigated.