Method for Preparation of Semiconductor Quantum‐Rod Lasers in a Cylindrical Microcavity

An efficient method for preparation of semiconductor quantum rod films for robust lasing in a cylindrical microcavity is reported. A capillary tube, serving as the laser cavity, is filled with a solution of nanocrystals and irradiated with a series of intense nanosecond laser pulses to produce a nanocrystal film on the capillary surface. The films exhibit intense room‐temperature lasing in whispering‐gallery modes that develop at the film–capillary interface as corroborated from the spacing detected for the lasing modes. Good lasing stability is observed at moderate pump powers. The method was applied successfully to several quantum‐rod samples of various sizes.     

Finite element analysis of electromagnetic scattering from a cavity

A finite element method (FEM) is implemented to compute the radar cross section of a two-dimensional (2D) cavity embedded in an infinite ground plane. The method is based on the variational formulation which uses the Fourier transform to couple the fields outside the cavity and those inside the cavity; hence, the scattering problem can be reduced to a bounded domain. The convergence of the discrete finite element problem is analyzed. Numerical results are presented and compared with those obtained by the standard finite element-Green function method and by the 2D integral equation method.     

Ozone measurement in visible region: an optical fibre sensor system

Ozone measurement based on the optical absorption of visible light at 603 nm using polymer optical fibres is investigated and tested. Comparisons with a commercial UV based sensor demonstrate the ability of the visible based sensor to measure high concentrations over a range 27-127 mg/litre. A resolution of 5 mg/litre is also demonstrated for this sensor.     

Transconductance and mobility of Si:B delta MOSFETs

Delta-doped MOSFETs have been fabricated in MBE-grown silicon using for the first time boron as the dopant within the delta layer. Current-voltage characteristics have been measured, and secondary ion mass spectrometry (SIMS) is used to confirm the location of the delta layer and the extent of layer broadening by diffusion during processing. Precise threshold voltages of the devices are difficult to determine since the devices (which all operate in depletion mode) take several volts to switch off. Transconductances of the devices have been measured, and it is shown how analysis of these results can yield estimates of the carrier mobility for transport along the delta layers despite the uncertainty in the threshold voltage. A clear transition is observed in the results which is attributed to the formation of a parasitic surface-channel field-effect transistor, providing conclusive evidence that the devices are conducting along a delta channel for part of the measured range of applied gate biases     

The Transmogrifier-2: a 1 million gate rapid-prototyping system

This paper describes the Transmogrifier-2 (TM-2), a second-generation multifield programmable gate array (FPGA) rapid-prototyping system. The largest version of the system will comprise 16 boards that each contain two Altera 10K50 FPGA's, four I-Cube interconnect chips, and up to 8 Mbytes of memory. The inter-FPGA routing architecture of the TM-2 uses a novel interconnect structure, a nonuniform partial crossbar, that provides a constant delay between any two FPGA's in the system. The TM-2 architecture is modular and scalable, meaning that systems of various sizes can be constructed from copies of the same board, while maintaining routability and the constant delay feature. Other features include a system-level programmable clock that allows single-cycle access to off-chip memory, and programmable clock waveforms with edge resolution of 10 ns. The first Transmogrifier-2 boards have been manufactured and are functional. They have recently been used successfully in some simple graphics acceleration applications     

Detailed nuclear structure studies far from stability

State-of-the-art spectroscopy of nuclei far from stability has achieved an extraordinary level of sophistication and detail in the last ten years. In principle, if a state can be populated, it can be characterized by its energy, spin, parity, and major decay paths. Sometimes its lifetime can be measured. In practice, one is confronted with enormous complexity. To convert raw spectroscopic data into nuclear structure data involves a complex process of disentangling gamma rays and conversion electrons into decay schemes. Specifically, coincidence techniques, especially coincidence intensities, play a crucial role in this process. Recent examples and methods from work done at UNISOR are presented.