尼龙6与半芳香性非晶尼龙原位共混物的结构与性能

一种半芳香的非晶尼龙共聚物溶解于熔融的己内酰胺中,引发后者负离子开环聚合原位制备尼龙6与非晶尼龙的共混物.与纯尼龙6相比较,此原位共混物的强度与模量显著提高.非晶区呈现单一的玻璃化转变,表明共混物为均相体系,其组分的相容性源于负离子聚合过程中链交换反应引起的共聚.与纯尼龙6相比较,此共混物的熔点与结晶度显著降低.此外,与纯尼龙6只存在α晶不同,共混物中伴生有大量的γ晶.当非晶尼龙含量为20 wt%时,绝大部分晶体为γ晶.然而,共混物中球晶仅有一定程度细化.共混物强度和模量的提高被认为主要源于非晶区分子活动能力降低以及γ晶相对含量的提高.     

LOW DENSITY POLYETHYLENE/CLAY NANOCOMPOSITES MODIFIED BY ETHYLENE COPOLYMERS： EFFECTS OF FUNCTIONALIZED SEGMENTS ON MORPHOLOGY

Melt extrusion was used to prepare binary nanocomposites of ethylene copolymers and organoclay and trinary nanocomposites of low-density polyethylene （LDPE）, ethylene copolymer and organoclay. X-ray diffraction （XRD） and transmission electron microscopy （TEM） were used to analyze the structure of the clay phase and the morphology of the nanocomposites. Influences of the comonomer in the copolymer and the content of the copolymer on the morphology of the resulting nanocomposites were discussed. The binary and the trinary composites may form intercalated or exfoliated structures depending on the interaction between the copolymer and the clay layers and the content of the copolymer.     

Influence of clay on the morphology and phase separation behavior of poly(methyl methacrylate)/poly(styrene-co-acrylonitrile) blends

The effect of clay on the morphology and phase-separation behavior of poly(methyl methacrylate)/poly(styreneco-acrylonitrile)(PMMA/SAN) blends and the variation of clay dispersion have been investigated. With the evolution of phase separation in PMMA/SAN, most of the clays are first located at the boundaries between PMMA and SAN, and then gradually move to the PMMA-rich domain, owing to the affinity of clay to PMMA. The introduction of clay causes the increase of binodal and spinodal temperatures of PMMA/SAN and enlarges their metastable region, indicating the phase stabilizing effect of clay on the matrix. But the influence of clay on the cloud points obviously depends on the composition of PMMA/SAN. The selective adsorption of PMMA on the clay results in the difference between the composition of surface layer and that of polymer matrix. Hence, the clay plays the role of an agent changing the conditions of phase structure formation.     

纳米层状双金属氢氧化物改性PU/PMMA的制备及其弛豫行为

采用原位聚合法,制备了聚氨酯(PU)/聚甲基丙烯酸甲酯(PMMA)/层状双金属氢氧化物(LDH)纳米复合体系(PU/PMMA/LDH).通过广角X射线衍射(WXRD)、透射电子显微镜(TEM)对其结构和形貌进行了表征,并通过热失重(TGA)、动态力学分析(DMA)和宽频介电谱(BDRS)研究了LDH含量(φ)对PU/PMMA体系热稳定性和弛豫行为的影响.结果表明,当φ<1 wt%时,LDH在聚合物基体中以剥离结构为主,PU/PMMA/LDH体系的玻璃化温度(Tg)降低,最大损耗因子(tanδmax)增大;而当φ>1 wt%时,LDH在聚合物基体中以插层结构为主,插层结构对聚合物分子链的限制使复合体系的Tg升高、tanδmax降低.LDH表面与PU硬段间的氢键作用,使复合体系的α介电弛豫转变随φ增加而向高温方向移动,弛豫过程激活参数增大.     

剪切作用下纳米粘土对LDPE熔体粘弹响应的影响

以LDPE/EVA/纳米粘土复合体系为研究模型,考察了剪切作用下,分散良好的纳米粘土对聚合物基体熔体稳态及瞬态粘弹响应的影响.发现剪切作用下,纳米粘土增加了聚合物熔体粘弹特性对剪切速率、剪切应变及剪切作用史的依赖性,改变了相应的依赖关系.稳态剪切时,纳米粘土的加入使体系第一法向应力差(N1)在低剪切速率区变为负值,而在高剪切速率区N1与粘土的含量无关;同时就瞬态剪切应力及N1的应变依赖关系而言,复合体系明显不同于聚合物基体;预剪切对聚合物基体瞬态粘弹响应几乎没有影响,而当纳米粘土的加入量大于3wt%后,与未经预剪切的样品相比较,经预剪切的复合体系的瞬态剪切应力值、应力过冲程度以及稳态剪切应力值均明显下降,且预剪切前后复合体系达到稳态时其瞬态剪切应力差值随纳米粘土含量的增高而线性增加.此外,纳米粘土的添加对聚合物熔体受剪切作用的非线性粘弹响应存在影响.复合体系熔体呈现特异非线性粘弹响应,其缘由被认为是由于纳米粘土在聚合物基体中剥离分散,或聚合物分子链插层于粘土片层间,形成局部有序结构,受剪切作用而排列取向.     

SiO2粒子对PMMA/SAN共混体系相分离行为的影响

采用小角激光光散射(SALLS)并结合动态流变学方法,考察了气相法二氧化硅(SiO2)粒子的加入对聚甲基丙烯酸甲酯/苯乙烯-丙烯腈无规共聚物(PMMA/SAN)共混体系相行为的影响,得到了添加SiO2粒子前后的相图,发现SiO2粒子对基体相行为的影响与基体的组成有关.对PMMA/SAN(60/40)体系,加入SiO2粒子后相分离温度上升,但并未改变相分离机理,仍为亚稳单相分解过程(spinodal decomposition,SD);而对于PMMA/SAN(30/70)体系,加入SiO2粒子后却降低了体系的相分离温度.该现象可能是SiO2粒子和基体组分界面间组成与PMMA/SAN共混物基体组成的差异造成的.     

白云石制备似立方体状方解石型碳酸钙晶体及其机理研究

以轻烧白云石粉、氯化铵和二氧化碳为原料,在未使用晶型控制剂的情况下,通过蒸氨-沉钙过程制备出了似立方体状碳酸钙。研究了反应温度、溶液中钙离子浓度、通气速率、搅拌速度以及陈化时间对碳酸钙中方解石相含量以及晶体形貌的影响,并探索了沉钙反应的晶型控制机理。结果表明,在反应温度40 ℃、钙离子浓度0.05 mol/L、通碳速率100 mL/min、搅拌速度400 r/min和陈化时间2 h的条件下,制备出形貌规整、粒径分布均匀的似立方体状碳酸钙,平均粒径为5~10 μm。该研究为提升白云石的使用价值、生产高附加价值的碳酸钙产品,以及提高白云石资源的利用率提供理论基础。     

苯乙烯-马来酸酐共聚物增容Nylon-6/ABS共混体系的形态和力学性能

通过熔融共混法制备了苯乙烯-马来酸酐共聚物(SMA)增容的尼龙6(Nylon-6)/ABS共混物.采用TEM、SEM、FTIR等研究了SMA增容的Nylon-6/ABS共混物的相形态与性能.发现在Nylon-6和ABS的简单共混体系中,分散相易聚集,相界面清晰,断裂面光滑,呈脆性断裂,相容性差.加入少量SMA后,共混物由共连续相结构转变为典型的"海-岛"结构,分散相分布均匀,界面粘接程度增加,表明SMA对Nylon-6/ABS体系有显著的增容效果.     

Theoretical investigation of the Gamow-Teller transition across N=40 shell

The Gamow-Teller transitions for pf shell nuclei with proton number less than 40 and neutron number larger than 40 were believed to be blocked, due to the full filling of the neutron orbit. However, recent experimental research shows that the Gamow-Teller transitions for these kinds of nuclei are not blocked. In this paper, we systematically calculate the GT transition of pf shell nuclei ⁷⁶Se in different truncations, and the results are compared with experimental results. It is shown that, due to correlations, the believed blocked GT transition occurs, and the shell model calculations reproduce the experimental GT strength. In addition, the electron capture rates in a stellar environment are calculated and discussed.     

气相二氧化硅填充极性低聚物的界面与流变

气相二氧化硅(FS)/低聚物纳米复合材料应用广泛于涂料、胶黏剂、锂离子电池、液体防弹衣等诸多领域.然而,极性低聚物与FS表面相互作用复杂,FS/低聚物复合材料(ONCs)的流变响应多种多样.如何实现ONCs流变行为调控,是长期困扰工业界的难题.本文详细总结了FS在ONCs领域的应用,将FS粒子间相互作用与ONCs流变性质相关联,综述ONCs界面层结构的表征、调控手段及界面层与流变行为的关系.结合本课题组对FS/极性低聚物体系界面及流变行为的研究成果,提出未来ONCs领域的2个重要方向,即研究界面结构与粒子-极性低聚物相互作用间的关系,并通过界面设计实现对纳米粒子/极性低聚物复合材料的流变行为的精确调控.