排序方式: 共有7条查询结果,搜索用时 922 毫秒
1
1.
由于高速移动,车车、车路通信信道存在较大多普勒频移,同时接收信号到达角不符合均匀分布。针对该特点,采用了两种方法进行信道建模,一种是采用R.von Mises提出的概率密度谱函数对多径散射信号到达移动接收机的角度进行建模,另一种是通过研究接收机和发送机之间相对运动进行建模。采用自回归模型法,根据不同的到达角平均方向、发射机和接收机速度比率和到达角宽,建立了不同的车车信道。仿真结果表明所建立的信道理论值与仿真值基本一致,同时揭示了3个参数对车车、车路信道模型二阶特性的影响。为了进一步验证不同信道模型对车车、车路通信的影响,搭建了下一代智能交通通信协议IEEE 802.11p系统测试平台,结果表明在最大多普勒频移为790 Hz、信噪比为5 d B时,简单二维各向异性散射信道比AKKI信道的系统误比特率低17.17 d B,三种信道的误比特率随着移动速度、调制阶数的提高而提高。仿真结果为研究智能交通系统稳定通信建立了基础。 相似文献
2.
A three-stage 4.8-6 GHz monolithic power amplifier(PA) compatible with IEEE 802.11a/n designed based on an advanced 2μm InGaP/GaAs hetero-junction bipolar transistor(HBT) process is presented.The PA integrates input matching and closed-loop power control circuits on chip.Under 3.3 V DC bias,the amplifier achieves a ~31 dB small signal gain,excellent wide band input and output matching among overall 1.2 GHz bandwidth,and up to 24.5 dBm linear output power below EVM 3%with IEEE 802.11a 64QAM OFDM input signal. 相似文献
3.
基于0.5 μm InGaAs pHEMT工艺,设计了一款应用于“北斗二号”导航系统的共源共栅低噪声放大器,其工作频率为1 575.42 MHz。该设计采用具有源端电感负反馈的电路结构,实现良好的输入匹配和反向隔离性能。输出端采用T-型匹配,支持大功率信号传输。测试结果表明,该低噪声放大器的增益S21为17.9 dB,噪声系数NF为0.92 dB,输入反射系数S11和输出反射系数S22分别为-9.9 dB和-10.9 dB,在2.85 V电压下,功耗为22 mW,且芯片面积仅为0.46 mm2,满足北斗导航系统要求。 相似文献
4.
A three-stage power amplifier (PA) for WLAN application in 2.4-2.5 GHz is presented. The proposed PA employs an adaptive bias circuit to adjust the operating point of the PA to improve the linearity of the PA. Two methods to short the 2nd harmonic circuit are compared in the area of efficiency and gain of the PA. The PA is taped out in the process of 2 μm InGaP/GaAs HBT and is tested by the evaluation board. The measured results show that 31.5 dB power gain and 29.3 dBm P1dB with an associated 40.4% power added efficiency (PAE) under the single tone stimulus. Up to 26.5 dBm output power can be achieved with an error vector magnitude (EVM) of lower than 3% under the 64QAM/OFDM WLAN stimulus. 相似文献
5.
6.
7.
基于2μm的InGaP/GaAs异质结双极晶体管(HBT)工艺设计了一种可应用于IEEE802.11 b/g/n无线局域网(WLAN)的高线性度射频功率放大器.为了提高射频功率放大器的线性度,采用了负反馈镜像电路提供直流工作点,设计了良好的输入、输出和级间匹配电路来提高射频功率放大器的线性输出功率.流片结果表明,在工作电压为3.3V时,射频功率放大器的1 dB线性压缩输出功率(P1dB)可达27 dBm,当误差向量幅度(EVM)为3%时,2.4 GHz64 QAM激励下,输出功率可达19.8 dBm,满足标准规范要求. 相似文献
1