Design of a widely tunable laser with a chirped ladder filter

We theoretically investigated a digitally tunable laser with a chirped ladder filter and a ring resonator to obtain a wide wavelength tuning range covering the whole C- or L- band. The clear relation between the tuning range and laser structure, especially the ladder filter, is described analytically. The introduction of a chirped structure into a ladder filter is effective in achieving both wide tunability and a stable lasing mode. A numerical simulation based on multimode rate equations shows that a tuning range of over 40 nm and a mode suppression ratio over 40 dB can be achieved by introducing a chirped ladder filter.     

Supported molybdena catalysts: Characterization of oxidized,reduced, and sulfided MoO3 prepared by an adsorption method

Highly dispersed molybdena-titania catalyst can be prepared by an equilibrium adsorption method. In this method, molybdate anions adsorb onto the positively charged titania surfaces via electrostatic attraction by controlling the pH of the impregnating solution and they increase as an inverse function of the pH. ⁹⁵Mo-NMR and UV spectroscopic studies of impregnating solution show that the polymeric species like Mo₇O₂₄ ⁶-ions are adsorbed on titania in the acidic impregnating solution. XRD, Raman, and XPS data of the calcined samples show that mono-layer coverage of molybdenum oxide over-layer possesses a highly distorted MoO₆ group with a molecular geometry resembling the distorted square pyramid. The catalytic oxidation of methanol over the surface molybdate species on titania possesses higher turnover numbers and higher selectivities of partial oxidation products than the catalysts supported on alumina, silica, zirconia, or magnesia. Changes of the surface properties either after reduction and sulfiding treatment over monolayer catalyst on titania have also been investigated. The NO chemisorption and XPS studies show that two types of active sites appeared after reduction treatment: one site is active for hydrogenation of 1,3-butadiene and the other site is active for metathesis of propene. A higher degree coordinative unsaturations of MO is required for hydrogenation than metathesis. After sulfiding treatments of the catalyst, hydrogenation of 1,3-butadiene also requires triply coordinative unsaturation, and hydrogenolysis of thiophene requires the ensemble of doubly or triply coordinative unsaturations.     

Phase separation and extraction with acetonitrile for sample preparation in HPLC analysis

Summary Acetonitrile can be salted-out from aqueous solution by adding tetrabutylammonium perchlorate. This phase separation method has been used for the extraction of the Fe(III)-4,7-diphenylphenanthroline complex into acetonitrile followed by direct injection onto an ODS column. The Fe complex is separated by using 9:1 acetonitrile/water as a mobile phase. The proposed reversed-phase high-performance liquid chromatography has been applied to the determination of Fe in serum.     

Fluorimetric determination of isatin in human urine and serum by liquid chromatography postcolumn photoirradiation

For the fluorimetric determination of isatin in human urine and serum, HPLC-postcolumn photoirradiation using a mobile phase has been developed. Isatin in the urine or serum sample was separated on a Capcell Pak C1 column (250 x 4.6 mm id). The mobile phase consisted of 70 mmol l-1 phosphate buffer (pH 7.2)-tetrahydrofuran (85 + 15% v/v) containing 5 mmol l-1 hydrogen peroxide, which was irradiated with germicidal light to induce fluorescence (lambda ex 302 nm, lambda em 418 nm). The addition of tetrahydrofuran to the mobile phase led to the peaks showing good separation as well as increased sensitivity. The calibration graph for isatin was linear over the range of 0.16-10.7 ng. The pretreatment of the acidified urine or serum samples consisted of diluting steps or deproteinizing steps using perchloric acid, respectively. The mean recovery of isatin from urine and serum was greater than 94%.     

Combustion behaviors of isolated n-decane and ethanol droplets in carbon dioxide-rich ambience under microgravity

The burning and sooting behaviors of isolated fuel droplets for ethanol and n-decane are examined in high concentration of the ambient carbon dioxide under microgravity. A quartz fiber with the diameter of 50 μm maintains the droplet in the center of the combustion chamber and the range in the initial droplet diameter is from 0.30 to 0.80 mm. The ambience consists of oxygen, nitrogen and carbon dioxide. The concentration of oxygen is 21% in volume, and that of carbon dioxide is varied from 0% to 60% in volume. Detail measurements of the projected image of the droplet are conducted by using a high speed video camera and the effective droplet diameter squared are calculated from the surface area of the rotating body of the projected object. From evolutions of the droplet diameter squared, the instantaneous burning rates are calculated. Time history of the instantaneous burning rate clearly represents the droplet combustion events, such as the initial thermal expansion, ignition and following combustion. The instantaneous burning rate for n-decane shows an increasing trend during combustion, while that for non-sooting ethanol remains almost constant or shows a decreasing trend. A slight stepwise increase in the instantaneous burning rate is observed for larger n-decane droplets in air, which may be attributed to soot accumulation. However, this behavior of the burning rate disappears in higher concentration of carbon dioxide. Direct observation of the droplet flame indicates suppression of soot production in higher concentration of carbon dioxide and the suppression is enhanced for smaller droplet.     

High-transmission waveguide with a small radius of curvature at a bend fabricated by use of a circular photonic crystal

A bent photonic crystal waveguide was fabricated by use of a lattice pattern of a circular photonic crystal that allowed high transmission for a broad band of wavelengths with a small radius of curvature at a bend. The waveguide was fabricated by use of alumina rods with a diameter of 3 mm. Windows of high transmission as a result of waveguiding were observed near 9 and 15 GHz. By measurement of the relative wave intensity [E]2 along the line defects, the propagation losses in the straight and the bent sections were estimated at 9.3 GHz to be 0.04 and 0.03 dB/mm, respectively.     

Evolution of the Hall coefficient and the peculiar electronic structure of the cuprate superconductors

Although the Hall coefficient R(H) is an informative transport property of metals and semiconductors, its meaning in the cuprate superconductors has been ambiguous because of its unusual characteristics. Here we show that a systematic study of R(H) in La2-xSrxCuO4 single crystals over a wide doping range establishes a qualitative understanding of its peculiar evolution, which turns out to reflect a two-component nature of the electronic structure caused by an unusual development of the Fermi surface recently uncovered by photoemission experiments.