Estimation of growth rate in unidirectionally solidified multicrystalline silicon by the growth-induced striation method

Multicrystalline silicon was grown by unidirectional solidification method using the accelerated crucible rotation technique. The application of the accelerated crucible rotation technique in unidirectional solidification method induced growth striations across the axial direction of the grown crystal. This striation pattern was observed from carbon concentration distribution, obtained by using Fourier transform infrared spectroscopy. The generated striation pattern was found to be weak and discontinuous. Some striations were absent, probably due to back melting, caused during each crucible rotation. From the growth striations and applied time period in crucible rotation, the growth rate was estimated by using Fourier transformation analysis.     

Integral Representations,Differentiability Properties and Limits at Infinity for Beppo Levi Functions

The first aim in the present paper is to give an integral representation for Beppo Levi functions on R ⁿ. Our integral representation is an extension of Sobolev's integral representation given for infinitely differentiable functions with compact support. As applications, continuity and differentiability properties of Beppo Levi functions are studied.Our second aim in this paper is to study the existence of limits at infinity for Beppo Levi functions. We also consider the existence of fine-type limits at infinity with respect to Bessel capacities, which yields the radial limit result at infinity.     

Complex impedance spectra of chip inductor using Li–Zn–Cu–Mn ferrite

A multi-layer chip inductor (MCI) was fabricated using polycrystalline Li–Zn–Cu–Mn ferrite and the green-sheet technique, and its complex impedance spectrum was evaluated with the help of numerical calculations. The complex impedance spectra of the MCI component using Ni–Zn–Cu ferrite, which have been widely used for this application, were very sensitive to the residual stress and deviated much from the calculated values; however, it was found that the complex impedance spectrum of the MCI component using Li–Zn–Cu–Mn ferrite is quite well reproduced by calculation, where the complex permittivity and permeability of the polycrystalline ferrite as well as the MCI dimensions, were used. It implied that the magneto-striction effect was negligible in case of MCI using Li–Zn–Cu–Mn ferrite, and that the difference was related to magneto-strictive coefficient of the polycrystalline ferrite. Consequently, utilization of Li–Zn–Cu–Mn ferrite enabled us to easily design the complex impedance of MCI component.     

Hydrolysis of acetals in water under hydrothermal conditions

A simple method for the hydrolysis of acetals and ketals was accomplished in neutral water or aqueous media by hydrothermal treatment without using acidic reagents. The deacetalization reaction was effectively accelerated in the presence of calcium chloride. Because no acidic catalysts were employed, neutralization of the reaction mixture was not necessary after the reaction. This sequence was successfully applied to the hydrolysis of chitosan, a biodegradable polyaminosaccharide.     

Design of a widely tunable laser with a chirped ladder filter

We theoretically investigated a digitally tunable laser with a chirped ladder filter and a ring resonator to obtain a wide wavelength tuning range covering the whole C- or L- band. The clear relation between the tuning range and laser structure, especially the ladder filter, is described analytically. The introduction of a chirped structure into a ladder filter is effective in achieving both wide tunability and a stable lasing mode. A numerical simulation based on multimode rate equations shows that a tuning range of over 40 nm and a mode suppression ratio over 40 dB can be achieved by introducing a chirped ladder filter.     

Imprinting by hot embossing in polymer substrates using a template of silica glass surface-structured by the ablation of LIBWE method

Laser-induced backside wet etching (LIBWE) of silica glass plates was performed to fabricate an imprinting template for hot embossing in polymer substrates such as polystyrene and silicone resin. Well-defined inverse surface-micropatterns of gratings and grid arrays on the substrates were produced by the hot embossing using a surface-structured silica glass as the template. These results indicate that the LIBWE method allows us to generate robust glass molding tools that exhibit the inverse shapes of the intended microstructures. PACS 52.38.Mf; 68.47.Mn; 81.05.Kf; 81.05.Lg; 83.50.Uv     

Fiber-in-Tube Solid Phase Extraction (FIT-SPE) for Miniaturized Sample Preparation Process

A typical analytical separation procedure has several important steps: sample preparation, isolation, identification, quantitation, statistical evaluation and final decision. Each step is alwayscritical to obtain correct results to fulfill the analytical purpose. In these various steps sample     

Stereo- and regio-selective formation of 2-oxazolone telomers as potential synthetic intermediates for aminosugars

3-Acetyl-2-oxazolone readily undergoes free-radical homopolymerization as well as telomerization with polyhalomethanes, in which low telomer formation is highly stereo- and regio-selective.     

Drug-carrying latices for prolonged release of drugs

Dichlorophene was used as a model drug. Drug-carrying latex particles were prepared by soap-free emulsion copolymerization of dichlorophene acrylate with some hydrophilic methacrylate comonomers. The comonomers used affected not only the structure and colloidal stability of particles, but also the drug-activity of particles. Preliminary study of the drug activity revealed that highly hydrophilic latex particles were very stable and too inactive to be engulfed by amoebae and kill them. On the contrary, less hydrophilic particles carrying a large amount of drug can be an effective device to release drugs at a moderate rate to fight against extracelluar targets such as parasites.     

Thermodynamic Insight into the Origin of a Calix[n]arene-[60]fullerene Interaction and its Application to a Porphyrin-[60]fullerene Energy Transfer System

The calixarene-fullerene interaction,which causes only a slight change in the absorptionspectra, has been substantiated by calorimetricmeasurements: the H° values arecomparable with those obtained from the associationconstants estimated by a spectroscopic method. Furthermore, we determined the association constantbetween homooxacalix[3]arene and [60]fullerenederivatives with a porphyrin moiety by fluorescencespectra.