Estimation of growth rate in unidirectionally solidified multicrystalline silicon by the growth-induced striation method

Multicrystalline silicon was grown by unidirectional solidification method using the accelerated crucible rotation technique. The application of the accelerated crucible rotation technique in unidirectional solidification method induced growth striations across the axial direction of the grown crystal. This striation pattern was observed from carbon concentration distribution, obtained by using Fourier transform infrared spectroscopy. The generated striation pattern was found to be weak and discontinuous. Some striations were absent, probably due to back melting, caused during each crucible rotation. From the growth striations and applied time period in crucible rotation, the growth rate was estimated by using Fourier transformation analysis.     

Integral Representations,Differentiability Properties and Limits at Infinity for Beppo Levi Functions

The first aim in the present paper is to give an integral representation for Beppo Levi functions on R ⁿ. Our integral representation is an extension of Sobolev's integral representation given for infinitely differentiable functions with compact support. As applications, continuity and differentiability properties of Beppo Levi functions are studied.Our second aim in this paper is to study the existence of limits at infinity for Beppo Levi functions. We also consider the existence of fine-type limits at infinity with respect to Bessel capacities, which yields the radial limit result at infinity.     

Complex impedance spectra of chip inductor using Li–Zn–Cu–Mn ferrite

A multi-layer chip inductor (MCI) was fabricated using polycrystalline Li–Zn–Cu–Mn ferrite and the green-sheet technique, and its complex impedance spectrum was evaluated with the help of numerical calculations. The complex impedance spectra of the MCI component using Ni–Zn–Cu ferrite, which have been widely used for this application, were very sensitive to the residual stress and deviated much from the calculated values; however, it was found that the complex impedance spectrum of the MCI component using Li–Zn–Cu–Mn ferrite is quite well reproduced by calculation, where the complex permittivity and permeability of the polycrystalline ferrite as well as the MCI dimensions, were used. It implied that the magneto-striction effect was negligible in case of MCI using Li–Zn–Cu–Mn ferrite, and that the difference was related to magneto-strictive coefficient of the polycrystalline ferrite. Consequently, utilization of Li–Zn–Cu–Mn ferrite enabled us to easily design the complex impedance of MCI component.     

Hydrolysis of acetals in water under hydrothermal conditions

A simple method for the hydrolysis of acetals and ketals was accomplished in neutral water or aqueous media by hydrothermal treatment without using acidic reagents. The deacetalization reaction was effectively accelerated in the presence of calcium chloride. Because no acidic catalysts were employed, neutralization of the reaction mixture was not necessary after the reaction. This sequence was successfully applied to the hydrolysis of chitosan, a biodegradable polyaminosaccharide.     

Design of a widely tunable laser with a chirped ladder filter

We theoretically investigated a digitally tunable laser with a chirped ladder filter and a ring resonator to obtain a wide wavelength tuning range covering the whole C- or L- band. The clear relation between the tuning range and laser structure, especially the ladder filter, is described analytically. The introduction of a chirped structure into a ladder filter is effective in achieving both wide tunability and a stable lasing mode. A numerical simulation based on multimode rate equations shows that a tuning range of over 40 nm and a mode suppression ratio over 40 dB can be achieved by introducing a chirped ladder filter.     

Strength of cylinder joint adhesively bonded by coupling

Summary A method of joining two metal cylindrical shafts with adhesive coupling is proposed. Two cylindrical shafts with the same diameter are connected by bonding through a cylindrical coupling with epoxy resin. The strength of the shaft joint under tensile loading and torsional loading is investigated analytically and experimentally. The stress and strain distributions of the shaft joint is analyzed by the finite element method. The analyzed strain distributions in the joint are compared with experimental values. The joint strength is predicted by applying the strength laws of shafts, coupling, adhesive layer and adhesive interface between shaft and adhesive coupling. The effects of the coupling dimension on the joint strength are examined. It is shown that the adhesive shaft joint can transfer the load by which the cylindrical shafts are plastically deformed.This paper was refined by the author, K. Ikegami, during statying at Technische Universität München under the support of Deutscher Akademischer Austauschdients. The author is grateful to Professor Lippmann of Technische Universität München who is the host professor of the support.     

Growth process of TiC clusters from Ti nanoparticles with evaporated carbon layer

Titanium carbide formation by the solid–solid reaction on the surface of Ti nanoparticles was studied in situ using a high-resolution transmission electron microscope with a heating stage. The cross-sectional image of the Ti surface was clearly observed. Vacuum-deposited carbon covered the whole the surface of Ti nanoparticles in spite of the partly evaporation on the nanoparticle surface. The diffusion of the carbon atoms inside the Ti nanoparticles depended on the size of the nanoparticles. When the Ti nanoparticle diameter was less than 30 nm, carbon atoms diffused into the Ti nanoparticle and formed TiC. The superstructure of the Ti nanoparticles was observed, which revealed the growth process of TiC to be the diffusion of carbon atoms. For Ti nanoparticles with diameter larger than 30 nm it was observed that diffusion of Ti atoms into the carbon layer was dominant, which resulted in formation of TiC in the carbon layer at the surface of Ti nanoparticles.     

Fiber-in-Tube Solid Phase Extraction (FIT-SPE) for Miniaturized Sample Preparation Process

A typical analytical separation procedure has several important steps: sample preparation, isolation, identification, quantitation, statistical evaluation and final decision. Each step is alwayscritical to obtain correct results to fulfill the analytical purpose. In these various steps sample     

Stereo- and regio-selective formation of 2-oxazolone telomers as potential synthetic intermediates for aminosugars

3-Acetyl-2-oxazolone readily undergoes free-radical homopolymerization as well as telomerization with polyhalomethanes, in which low telomer formation is highly stereo- and regio-selective.