Efficient regio- and stereoselective ring opening of epoxides with alcohols, acetic acid and water catalyzed by ammonium decatungstocerate(IV)

Epoxides can be cleaved in a regio- and stereoselective manner under neutral conditions with alcohols and acetic acid in the presence of catalytic amounts of decatungstocerate(IV) ion, ([CeW₁₀O₃₆]⁸⁻), affording the corresponding β-alkoxy and β-acetoxy alcohols in high yields. In water, ring opening of epoxides occurs with this catalyst to produce the corresponding diols in good yields.     

An efficient,expeditious, and diastereoselective one-pot pseudo-five-component reaction for the synthesis of new bis-Betti bases under catalyst-free conditions

A novel, diastereoselective, one-pot synthesis of new bis-Betti bases via condensation of dihydroxynaphthalene, two equivalents of aryl aldehydes, and two equivalents of 3-amino-5-methylisoxazole is reported. Conversion into the adducts was almost quantitative without the use of solvent or catalyst. The reaction conditions are very simple and enable easy isolation of the product.     

Ultrasound-assisted emulsification microextraction using low density solvent for analysis of toxic nitrophenols in natural waters

An ultrasound-assisted emulsification microextraction (USAEME) based on low-density solvents was successfully applied for the extraction and pre-concentration of four toxic nitrophenols in water samples. The extracted analytes were analyzed by high-performance liquid chromatography-UV detection. The important parameters influencing the extraction efficiency were studied and optimized utilizing two different optimization methods: one variable at a time (OVAT) and central composite design (CCD). The results showed that the emulsification process can be completed in a few seconds using low-density solvents, but almost 10–20?min is necessary for high-density solvents. Under the optimum conditions (extraction solvent, 1-octanol; extraction solvent volume, 40?µL; sample pH, 3.0; salt concentration, 20% (w/v) NaCl; extraction temperature, 40 (±3)°C), limits of detection of the method were in the range of 0.25 to 1?µg?L^?1 and the repeatability and reproducibility of the proposed method, expressed as relative deviation, varied in the range of 2.2–4.2% and 4.7–6.9%, respectively. Linearity was found to be in the range of 1 to 200?µg?L^?1 and the preconcentration factors (PFs) were between 77 and 175. The relative recoveries of the four nitrophenols from water samples at spiking level of 10.0?µg?L^?1 were in the range of 92.0 to 115.0%.     

A combined experimental and computational investigation of the binary mixtures of 2-methylcyclohexanol and isobutanol

Structural Chemistry - The measured densities and viscosities of the binary mixtures of the isobutanol and 2-methylcyclohexanol were reported experimentally in a certain range of concentrations at...     

A highly sensitive spectrophotometric determination of ultra trace amounts of azide ion in water and biological samples after preconcentration using dispersive liquid-liquid microextraction technique

A simple and highly sensitive method developed for preconcentration and spectrophotometric determination of ultra trace amounts of azide ion (N ₃ ^? ) in water and biological samples using dispersive liquid-liquid microextraction (DLLME) technique. The method is based on ion association formation of azide ion with malachite green and extraction of the ion pairing product using DLLME technique. Some important parameters, such as reaction conditions and the kind and volume of extraction solvent and disperser solvent were studied and optimized. The calibration curve was linear in the range of 0.5–50 μg/L of azide ion. Also, the enrichment factor and extraction recovery obtained were 24.7 and 98.7%, respectively. The method was applied to the determination of azide ion in water and biological samples.     

Outdoor ground impedance models

Many models for the acoustical properties of rigid-porous media require knowledge of parameter values that are not available for outdoor ground surfaces. The relationship used between tortuosity and porosity for stacked spheres results in five characteristic impedance models that require not more than two adjustable parameters. These models and hard-backed-layer versions are considered further through numerical fitting of 42 short range level difference spectra measured over various ground surfaces. For all but eight sites, slit-pore, phenomenological and variable porosity models yield lower fitting errors than those given by the widely used one-parameter semi-empirical model. Data for 12 of 26 grassland sites and for three beech wood sites are fitted better by hard-backed-layer models. Parameter values obtained by fitting slit-pore and phenomenological models to data for relatively low flow resistivity grounds, such as forest floors, porous asphalt, and gravel, are consistent with values that have been obtained non-acoustically. Three impedance models yield reasonable fits to a narrow band excess attenuation spectrum measured at short range over railway ballast but, if extended reaction is taken into account, the hard-backed-layer version of the slit-pore model gives the most reasonable parameter values.     

Microbubble-enhanced hemorrhage control using high intensity focused ultrasound

Our objective was to investigate whether hemorrhage control can be achieved faster when high-intensity focused ultrasound (HIFU) is applied in the presence of ultrasound contrast agents (UCA) as compared to HIFU only application. Incisions (3 cm long and 0.5 cm deep) were produced in the livers of anesthetized rabbits. UCA Optison (0.18 ml/kg) was injected into the mesenteric vein. A HIFU applicator (5.5 MHz, 6800 W/cm² in situ) was scanned at a rate of 1–2 mm/s in one direction over the incision (with multiple passes if needed), until hemostasis was achieved. Hemostasis times were 59 ± 23 s (n = 21) in the presence of Optison and 70 ± 23 s (n = 29) without Optison. The presence of Optison produced on average 37% reduction in hemostasis times normalized to initial bleeding rates (p < 0.05), as well as 60% faster formation of the coagulum seal over the incision (p < 0.05). Gross and histological observations showed similar appearance of HIFU lesions produced in the presence of Optison and HIFU lesions produced without Optison. Our results suggest potential utility of UCA for increasing efficiency of HIFU-induced hemostasis of solid organ injuries.     

The effect of reaction mixture movement on the performance of chromium-benzenedicarboxylate,MIL-101(Cr), applicable for CO2 adsorption through a new circulating solvothermal synthesis process

Journal of the Iranian Chemical Society - The primary objective of the present work was to investigate the effect of fluid movement on synthesized chromium-benzenedicarboxylate, MIL-101(Cr),...     

Photovoltaic cells technology: principles and recent developments

Solar energy is one of the renewable energy resources that can be changed to the electrical energy with photovoltaic cells. This article accomplishes a comprehensive review on the emersion, underlying principles, types and performance improvements of these cells. Although there are some different categorizations about the solar cells, but in general, all of them can be divided to crystalline silicon solar cells, thin film technology, III–V multijunction cells, dye-sensitized solar cells, polymer solar cells and quantum structured solar cells. Thin film technology is investigated in two non-crystalline silicon solar cells and chalcogenide cells. We present a complete categorization of solar cells and discuss the recent developments of different types of solar cells. Indeed, this paper covers almost all of the development processes of solar cells from their emersion in 1939 up to now. Also, due to substantial effects of the light trapping techniques on the improvements of the solar cells, a comprehensive study has been carried out.     

Molybdenum (VI)‐functionalized UiO‐66 provides an efficient heterogeneous nanocatalyst in oxidation reactions

A novel heterogeneous nanocatalyst was established by supporting molybdenum (VI) on Zr₆ nodes in the structure of the well‐known UiO‐66 metal–organic framework (MOF). The structure of the UiO‐66 before and after Mo (VI) immobilization was confirmed with XRD, DR‐FTIR and UV–vis spectroscopy, and the presence and amount of Mo (VI) was identified by X‐ray photoelectron spectroscopy and inductively coupled plasma atomic emission spectroscopy. TEM imaging confirmed the absence of Mo clusters on the MOF surface, while SEM confirmed that the appearance of the MOF has not changed upon immobilizing the Mo (VI) catalyst. BET adsorption measurements were used to confirm the porosity of the catalyst. The catalytic activity of this heterogeneous catalyst was investigated in oxidation of sulfides with H₂O₂ in acetonitrile and oxidative desulfurization of dibenzothiophene. Easy work up, convenient and steady reuse and high activity and selectivity are prominent properties of this new hybrid material.