In the present research, magnesium aluminate spinel was prepared as catalyst support using a novel, facile, and efficient mechanochemical method. The Co-promoted catalysts with 20 wt.% of Ni were fabricated using an impregnation route and the samples were analyzed by the X-ray diffraction (XRD), N2 adsorption/desorption (BET), temperature-programmed reduction and desorption (H2-TPR and O2-TPD), and field emission scanning electron microscopy (FESEM) tests. The results confirmed that all samples have a mesoporous structure with a high specific surface area and the presence of cobalt caused complete CH4 oxidation at low temperatures, and no side reactions were observed. The results indicated that the 3%Co-20%Ni/MgAl2O4 catalyst was the optimal sample among the prepared catalysts, owing to the improvement of reduction features and oxygen mobility. The 50 and 90% of methane conversion was obtained at 530 and 600 °C, respectively. Also, the influence of calcination temperature, GHSV, and feed ratio was determined on the catalytic activity. The obtained outcomes revealed that the calcination temperature has a significant effect on the textural properties and catalytic efficiency. The sample calcined at 700 °C showed the weakest performance, which was related to the sintering of particles at high temperatures. The catalytic stability showed that the 3%Co-20%Ni/MgAl2O4 has acceptable stability during 600 min time of reaction.
Journal of Thermal Analysis and Calorimetry - Artificial neural network/kriging interpolation method optimization method which is evaluated concerned the hybrid nanofluid composed of iron oxide... 相似文献
This study describes a technique that combines the benefits of focusing schlieren and phase conditioning. Focusing schlieren blurs and drops contrast of non-critical features whereas phase conditioning emphasizes periodic flow features, and their combination produces unique results. The supersonic jets that we studied produced an intense tone referred to as screech. The measured screech tone signal was used as input to the phase conditioning circuit that adjusted the strobing light source to the vertical synchronization pulse of a CCD camera. The sharp video images obtained by this technique could either be frozen or continuously swept through one period of screech to acquire a slow motion video record of the jet unsteadiness. Two cases were visualized in this study: first, an underexpanded jet from a convergent rectangular nozzle at various fully expanded Mach numbers. Second, a supersonic jet emerging from a convergent-divergent rectangular nozzle at a design Mach number of 1.4, artificially excited by impingement tones. The results of this study illustrate the usefulness of this system in visualizing oscillatory flows.The authors would like to thank Dr. Edward J. Rice for his contributions including the design of the impingement obstacles. The efforts of Brentley C. Nowlin (NASA Lewis), and James E. Little (NYMA Inc.) in the design and construction of the strobe trigger mechanism are highly appreciated. We also thank Janet Ivancic (NASA Lewis Photo Lab) for the image enhancement. 相似文献
Enthalpies of mixing (mH) aqueous solutions of CoCl2, CuCl2, and MnCl2 with NaCl solutions were measured at constant ionic strengths of 0.5, 1.0, and 3.0 molal at 25°C. The excess enthalpy equations of Pitzer were then fit to the resulting mH data. The resulting parameters are the temperature derivatives of the activity coefficient mixing parameters in the Pitzer system. The heat of mixing data for CoCl2 and CuCl2 were in agreement with earlier isomolal results by other workers. 相似文献
The dependency of adsorption energy (E) and affinity coefficient (beta) of Dubinin equations (Dubinin-Radushkevich (DR) or Dubinin-Astakhov (DA)) on surface chemistry and porosity of activated carbons was investigated by analyzing adsorption of nitrogen, benzene, trichloroethylene (TCE), and water vapor by several surface-modified activated carbons and carbon fibers. For all studied nonpolar adsorbates, carbons with smaller average micropores showed higher adsorption energies independent of their surface chemistry. For water vapor, carbons with higher surface polarities showed higher adsorption energies due to specific adsorbate-adsorbent interactions. Adsorption energies increased with decreasing average micropore widths. betaN2,DR for different carbons were observed to vary in the 0.292-0.539 range. Carbons with higher degrees of mesoporosity had higher betaN2,DR values, while no dependency was observed between betaN2,DR and surface chemistry. A comparison of DR and DA cases indicates that: (1) the average value of betaN2,DA is considerably above the classical value of this parameter; and (2) the range of betaN2,DA values were smaller compared to betaN2,DR, despite a wide range of mesoporosity of carbons examined. Obtained beta(TCE,DR) values varied in the 0.952-1.243 range, with an average value of 1.085+/-0.083, independent of surface chemistry or porosity of activated carbons. A similar result was observed for beta(TCE,DA). betaH2O,DR values of different granular and fibrous activated carbons changed in the range of 0.081-0.271. They depended more on the carbon surface chemistry and less on the porosity. A similar result was obtained when DA equation was considered. 相似文献
In this paper five equations of state are tested for checking their ability to predict the Joule-Thomson inversion curve.These five equations of state are:Mohsennia-Modarres-Mansoori(MMM),Ji-Lemp(JL),modified Soave-Redlich-Kwang(SRK)equation of state by Graboski(MSRK1),modified SRK equation of state by Peneloux and Rauzy(MSRK2),and modified Peng-Robinson (PR)equation of state by Rauzy(PRmr).The investigated equations of state give good prediction of the low-temperature branch of the inversion curve,except for MMM equation of state.The high-temperature branch and the peak of the inversion curve have been observed,in general,to be sensitive to the applied equation of state.The values of the maximum inversion temperature and maximum inversion pressure are calculated for each component used in this work. 相似文献
Epoxy-timber composites have received increasing attention during the last decades because there are many advantages related to their uses as construction materials in applications such as timber bridges. However, the durability of epoxy-timber composites under outdoor conditions has become a concern for many epoxy resins. This study evaluated the chemical, thermal, and mechanical properties of two cured epoxies, the product of the diglycidyl ether of bisphenol A with 2,4-trimethyl-1,6-hexanediamine (DGEBA-TMDA) and the analogous resin prepared with the hydrogenated diglycidyl ether of bisphenol A (HDGEBA-TMDA), each mixed with 2?wt. % calcium sulfate (CS). We hypothesized that the use of CS, as an inorganic UV absorber, could decrease undesirable effects arising from exposure to UV light, moisture, and extreme temperatures.
An accelerated aging chamber simulated natural weathering for 1, 2, 3, 4, and 6?months. Chemical changes in cured epoxy systems over time in the presence and absence of CS fillers were determined using Fourier transform infrared spectroscopy (FT-IR). Thermal degradation profiles before and after exposure to accelerated weathering were followed by thermogravimetric analysis (TGA). The glass transition temperatures (Tg) before and after accelerated weathering were measured, and the effect of accelerated weathering on the surface morphology of the epoxy systems was investigated by scanning electron microscopy (SEM). In the presence of CS, after 6?months accelerated weathering the tensile strength of DGEBA-TMDA reduced by 23.8?±?2.4%, compared to 46.5?±?5.5% in its absence, while the corresponding values for HDGEBA-TMDA were 21.4?±?2.1% and 28.7?±?1.8%. 相似文献