The interfacial conformation of polypropylene glycols and foam behaviour

The foam behaviour of low molecular weight polypropylene glycols (PPG) was investigated as a function of concentration and molecular weight (190–2000 g mol⁻¹). For each polypropylene glycol, foam stability increases with concentration and passes through a maximum, beyond which foamability is suppressed as the solubility limit of the glycol is exceeded and droplets of glycol form. Light-scattering data as well as static and dynamic surface tension results provide the key information leading to these interpretations. A maximum in foamability was observed for the PPG molecules with increasing molecular weight (caused by a change in molecular conformation at the interface). This suppresses the Marangoni effect and leads to a decrease in foam stability.     

On strongly stable normal operators in Krein spaces

For bounded normal operators in Krein spaces we give a necessary and sufficient condition for strong stability. The same result for unitary operators was obtained by M.G.Krein [1] (see also [2]). For selfadjoint operators we refer to the papers of P.Jonas, H.Langer [3] and H.Langer [4].     

InGaAs/GaAs multiple-quantum-well modulators and switches

The design, fabrication and characterization of electrooptical modulators and switches based on pseudomorphic InGaAs/GaAs multiple-quantum-well (MQW) structures is presented. The absorption and refractive index changes (, n) of In_0.2Ga_0.8As/GaAs MQW structures due to the quantum-confined Stark effect are examined in detail. The figures of merit /₀ and n/₀ give information on the design of modulation and switching devices. Based on these results, we develop two types of efficient and high-speed modulators, vertical and waveguide modulators, and for the first time an InGaAs/GaAs intersectional X-type switch. Recent experimental results for each device are presented.     

Influence of hydrolyzable metal ions on the interfacial chemistry, particle interactions, and dewatering behavior of kaolinite dispersions

The influence of hydrolyzable metal ions (Mn(II) and Ca(II)) adsorption on the surface chemistry, particle interactions, flocculation, and dewatering behavior of kaolinite dispersions has been investigated at pH 7.5 and 10.5. Metal ion adsorption was strongly cation type- and pH-dependent and significantly influenced the zeta potential, anionic polyacrylamide-acrylate flocculant (PAM) adsorption, shear yield stress, settling rate, and consolidation of kaolinite slurries. The presence of Mn(II) and Ca(II) ions alone led to a systematic reduction in zeta potential due to specific adsorption of positively charged metal ion-based hydrolysis products at the kaolinite-water interface. Metal ion-mediated zeta potential changes were reflected by lower dispersion shear yield stresses and improved clarification (higher settling rates) but had no detectable effect on dispersion consolidation. The adsorption of PAM was significantly improved by prior addition of the metal ions. In the presence of Mn(II) or Ca(II) ions, the flocculant adsorption density was enhanced at pH 7.5 for Mn(II) and pH 10.5 for Ca(II). Optimum flocculation conditions, involving partial rather than complete particle surface coverage by both metal ions and flocculant, were identified. As a consequence, the metal ions and flocculant acted synergistically to enhance dewatering, producing particle interactions that were more conducive to high settling rates and greater consolidation of kaolinite dispersions at pH 7.5 than 10.5.     

Pharmacokinetics of ICG and HPPH-car for the detection of normal and tumor tissue using fluorescence, near-infrared reflectance imaging: a case study

We present in vivo fluorescent, near-infrared (NIR), reflectance images of indocyanine green (ICG) and carotene-conjugated 2-devinyl-2-(1-hexyloxyethyl) pyropheophorbide (HPPH-car) to discriminate spontaneous canine adenocarcinoma from normal mammary tissue. Following intravenous administration of 1.0 mg kg-1 ICG or 0.3 mg kg-1 HPPH-car into the canine, a 25 mW, 778 nm or 70 mW, 660 nm laser diode beam, expanded by a diverging lens to approximately 4 cm in diameter, illuminated the surface of the mammary tissue. Successfully propagating to the tissue surface, ICG or HPPH-car fluorescence generated from within the tissue was collected by an image-intensified, charge-coupled device camera fitted with an 830 or 710 nm bandpass interference filter. Upon collecting time-dependent fluorescence images at the tissue surface overlying both normal and diseased tissue volumes, and fitting these images to a pharmacokinetic model describing the uptake (wash-in) and release (wash-out) of fluorescent dye, the pharmacokinetics of fluorescent dye was spatially determined. Mapping the fluorescence intensity owing to ICG indicates that the dye acts as a blood pool or blood persistent agent, for the model parameters show no difference in the ICG uptake rates between normal and diseased tissue regions. The wash-out of ICG was delayed for up to 72 h after intravenous injection in tissue volumes associated with disease, because ICG fluorescence was still detected in the diseased tissue 72 h after injection. In contrast, HPPH-car pharmacokinetics illustrated active uptake into diseased tissues, perhaps owing to the overexpression of LDL receptors associated with the malignant cells. HPPH-car fluorescence was not discernable after 24 h. This work illustrates the ability to monitor the pharmacokinetic delivery of NIR fluorescent dyes within tissue volumes as great as 0.5-1 cm from the tissue surface in order to differentiate normal from diseased tissue volumes on the basis of parameters obtained from the pharmacokinetic models.     

Morphology of adsorbed polymers and solid surface wettability

The adsorption of a polyacrylamide (MW 14600) and two polysaccharides (MW 9260 and 706 x 10(3)) onto model silica surfaces of different hydrophobicities was investigated. In all cases, adsorption adhered to the Freundlich isotherm, reflecting the heterogeneous character of the solid substrates. The latter strongly influenced the character of the adsorbed polymer, with morphologies from chainlike structures to thin films and patches being observed. Surface roughness, polymer type, and molecular weight also play roles in controlling adsorbed polymer morphology. Surface wettability is strongly influenced by the thickness of the adsorbed layer.