Tannins of tamarind seed husk: preparation, structural characterization, and antioxidant activities

The high content (about 39%) of polymeric tannins in tamarind (Tamarindus indica L.) seed husk (TSH) was demonstrated, and an extract (crude TSE) with a high content (about 94%) of polymeric tannins was prepared from TSH with a one pot extraction using ethanol/water (3:2, v/v). The crude TSE was further purified with Sephadex LH20 to give one fraction (metTSE) eluted with methanol/water (3:2, v/v) and another (acTSE) eluted with acetone/water (3:2, v/v). The tannins of acTSE were established as polymeric proanthocyanidins (PA) by 13C NMR spectroscopy; this was further confirmed by IR and UV spectroscopy, n-BuOH/HCl and vanillin assays, and from HPLC pattern. The ratio of procyanidins to prodelphinidins was 2:3, and the average degree of polymerization of acTSE was 7. Galloylated flavan-3-ols were not detected in acTSE. The main ingredients of metTSE were confirmed to be polymeric PA by 13C NMR spectroscopy. The antioxidant activities using DPPH and ABTS assays were investigated. The IC50 values of acTSE were 4.2 +/- 0.2 (DPPH assay) and 6.2 +/- 0.3 microg/mL (ABTS assay).     

Curcumin-sensitized TiO2 for enhanced photodegradation of dyes under visible light

Curcumin was coated on P25 TiO₂ by using impregnation method from freshly prepared curcumin solution. The resulting products (Cur–TiO₂–P25) was studied by several techniques such as X-ray diffraction, scanning electron microscopy, transmission electron microscopy, Fourier-transformed infrared spectroscopy, specific surface area by the Brunauer–Emmett–Teller method, and UV–Vis diffused reflectance spectroscopy. Experimental results revealed that impregnation of curcumin at 0.5, 3, 5, and 7 wt% did not affect the native phase of anatase and rutile in P25 significantly, however, it caused red shift of absorption onset in all curcumin-coated samples. The Cur–TiO₂–P25 showed enhanced adsorption efficiency and increased photocatalytic activity under visible light with optimal result at 5 wt% curcumin content. Commercial anatase and rutile coated with curcumin (Cur–TiO₂–an and Cur–TiO₂–ru) were also prepared by the same method for the use in comparative studies of photodegradation of dyes. Cur–TiO₂–an and Cur–TiO₂–ru were also characterized with some selected equipment above but not as extensively as the Cur–TiO₂–P25. Curcumin coating helped improve photocatalytic efficiencies of P25 and anatase but not for rutile. The mechanism of photocatalytic reaction was proposed that under visible light irradiation, curcumin molecule could act as dye sensitizing agent that injected electron into the conduction band of TiO₂ leading to photodegradation of dyes.     

Amorphous titanium dioxide as an adsorbent for dye polluted water and its recyclability

Amorphous TiO₂, synthesized from TiCl₄ and diluted NH₃ solution, was characterized by X-ray diffraction spectrometry, UV–Vis diffused reflectance spectroscopy, Fourier-transformed infrared spectroscopy, and scanning electron microscopy. The powder exhibited high specific surface area at 508 m²/g as measured by the Brunauer-Emmett-Teller method. The pH at point of zero charge of the as-prepared amorphous TiO₂ was determined by the pH drift method to be 6.8. The product was studied for its sorption efficiency using two dyes—crystal violet (CV) and malachite green (MG). Studies on the effects of various sorption parameters (contact time, TiO₂ dosage, pH of solution, and initial concentration of dye) were carried out in order to find the optimum adsorption conditions for which the results were: contact time ~30 min, TiO₂ dosage ~0.05–0.1 g, pH 7–9, and initial concentration <1 × 10^?4 M. The adsorption data were analyzed and fitted better with the Langmuir model than the Freundlich model. The maximum adsorption capacities obtained from the Langmuir model were 0.4979 and 0.4075 mmol dye/g TiO₂ for CV and MG dye, respectively. In addition, the regeneration and the recyclability of the prepared amorphous TiO₂ were also studied. The used adsorbent should be regenerated 10–12 h before reuse in the next cycle for the best result.