Magnetic hysteresis of the magnetoresistance and the critical current density in polycrystalline YBa2Cu3O7−δ–Ag superconductors

A systematic study of the magnetic hysteresis in transport properties of polycrystalline YBa₂Cu₃O_7−δ–Ag compounds has been made based on two kinds of measurements at 77 K and under applied magnetic fields up to 30 mT: critical current density J_c(B_a) and magnetoresistance R(B_a). The R(B_a) curves show a minimum in their decreasing branch occurring at B=B_min which was found to be both the excitation current I_ex and the maximum applied magnetic field B_am dependent. In addition, for a certain value of B_am>5 mT, we have observed that B_min increases with increasing I_ex and reaches a saturation value. The J_c(B_a) curves show a maximum in decreasing applied magnetic fields occurring at B=B_max. We have also found that B_max increases with increasing B_am and reaches a saturation value. The minimum in the R(B_a) and the maximum in J_c(B_a) curves were found to be related to the trapped flux within the grains. All the experimental results are discussed within the context of the flux dynamics and transport mechanisms in these high-T_c materials.     

Thermal and spectroscopic characterization of nanostructured zirconia–scandia–dysprosia

Zirconia containing 10 mol% scandia and x mol% dysprosia (0 ≤ x ≤ 1.5) gels was synthesized by simultaneous precipitation at room temperature. The aim of this work is to verify the effect of dysprosium on the cubic phase stabilization of the zirconia–scandia solid electrolyte. The gel was characterized by thermogravimetry, differential scanning calorimetry, and differential thermal analyses. The thermally treated powders were analyzed by Fourier transform infrared spectroscopy, thermal analyses, and X-ray diffraction techniques. For comparison purpose, a commercial zirconia–10 mol% scandia powder was subjected to some characterization techniques. The infrared spectrum shows characteristic absorption bands due to residual material from the synthesis on the surface of the powder particles. Nanostructured powders were obtained after thermal treatments at 500 °C for 2 h. Infrared spectroscopy and X-ray diffraction results evidence the stabilization of the cubic phase in zirconia–scandia containing dysprosium. The thermal stability of the cubic phase during thermal cycling was ascertained by thermal analysis.     

Synthesis and characterization of spherical and narrow size distribution indium oxide nanoparticles

This work reports the synthesis of indium oxide nanoparticles and their thermal, structural, microstructural and optical characterization. The preparation method is based on a surfactant-free room temperature soft chemistry route. Spherical indium oxide nanoparticles (about 8 nm in diameter) were obtained after thermal treatment of gels at 400 °C for 2 h, as shown by X-ray diffraction experiments and nitrogen adsorption measurements. Transmission electron microscopy observations confirm the single-crystalline nature of the produced nanoparticles. The photoluminescence emission spectrum at room temperature shows a broad peak with onset at approximately 315 nm as a result of quantum size effect as revealed by small-angle X-ray scattering.     

Impedance spectroscopy study of the sintering of yttria-stabilized zirconia/magnesia composites

In the present study, the sintering of (ZrO₂:8 mol%Y₂O₃)_1 ? m–(MgO)_m, YSZ–mMg composites, with m in the 0–30 mol% range, has been investigated by impedance spectroscopy (IS), dilatometry, and X-ray diffraction. Impedance diagrams were collected at 400 °C after heating the green compacts up to a selected sintering temperature, which was increased stepwise from 800 to 1400 °C. The combined experimental results revealed that the samples can be separated in two categories: below and above the solubility limit of MgO in the YSZ (m ~ 10). Moreover, important microstructural features associated with both the sintering process and solid solution formation of YSZ–mMgO samples were correlated to the electrical properties inferred by IS.     

Electric conduction-blocking effects of voids and second phases in stabilized zirconia

To elucidate the conduction-blocking process observed in sintered electric ceramics, measurements have been carried out on a weld between two YSZ (Yttria-Stabilized Zirconia) single crystals and on YSZ-Al₂O₃ composites in addition to previous measurements on cracks generated at room temperature in YSZ single crystals. A fraction of the mobile oxide ions appears to be blocked at impermeable parts of the internal surfaces. The surfaces of voids (cracks, pores, and probably parts of the grain boundaries) can generate the same blocking effects as the surface of precipitated second phases.     

Electrical conductivity of yttria-stabilized zirconia with cobalt addition

Yttria-stabilized zirconia is the most developed solid electrolyte for use in high-temperature solid oxide fuel cells. Commercial yttria-stabilized zirconia powders reach high densification at temperatures higher than that of the usual anode materials. Reduction of the sintering temperature of the solid electrolyte could allow for co-firing of both ceramic components, thereby reducing production costs. The main purpose of this work was to study the effect of small cobalt additions on densification and on electrical conductivity of 8 mol% yttria-stabilized zirconia. Linear shrinkage results show that the onset temperature for shrinkage decreases with increasing cobalt content. Impedance spectroscopy measurements reveal that the electrical conductivity depends on the sintering profile. For specimens sintered at 1400 °C for 0.1 h the electrical conductivity of grains and grain boundaries are almost unchanged with that of 8YSZ. In contrast, for specimens sintered at the same temperature but for 0.5 h of soaking time, the electrical conductivity is higher in 0.025 mol% samples and is lower for 1 mol% Co doped 8YSZ. Degradation of the microstructure by increased porosity was obtained for high additive contents.     

Master sintering curve for Gd-doped CeO<Subscript>2</Subscript> solid electrolytes

The sintering behavior of gadolinia-doped ceria powders was studied by the master sintering curve (MSC). Dilatometric analyses of powders produced by a soft chemical method were performed to provide the experimental data set for the construction of the MSC. The assumed model provided good fittings of the MSC and the activation energy for the sintering of Ce_1−x Gd _x O_3−δ, with x = 0, 0.05, 0.1, and 0.2 were found to be in the 218–325 KJ/mol range, depending on the dopant content. The results supported that both the nanometric size of the particles and the difference in ionic radii between Gd³⁺ and Ce⁴⁺ affects the sintering of Gd-doped CeO₂.     

Synthesis of In2O3nanoparticles by thermal decomposition of a citrate gel precursor

This paper describes the synthesis of indium oxide by a modified sol–gel method, and the study of thermal decomposition of the metal complex in air. The characterization of the intermediate as well as the final compounds was carried out by thermogravimetry, differential thermal analysis, Fourier transform infrared spectroscopy, X-ray diffraction, transmission electron microscopy, and small angle X-ray scattering. The results show that the indium complex decomposes to In₂O₃ with the formation of an intermediate compound. Nanoparticles of cubic In₂O₃ with crystallite sizes in the nanosize range were formed after calcination at temperatures up to 900°C. Calcined materials are characterized by a polydisperse distribution of spherical particles with sharp and smooth surfaces.     

Thermal and electrical properties of CaCu<Subscript>3</Subscript>Ti<Subscript>4</Subscript>O<Subscript>12</Subscript> synthesized by soft chemistry route

The non-isothermal sintering process of cerium dioxide containing gadolinium sesquioxide powders within a wide range of specific surface area was investigated by dilatometry. Linear shrinkage data of powder compacts were recorded under several constant rates of heating. Dilatometry data were analyzed by two methodologies enabling to preview the relative density for any temperature/time profile, and determination of the apparent activation energy for sintering. Correlation of dilatometry results with microstructure evolution was also carried out. Remarkable differences in sintering powders with different specific surface areas were found. The apparent activation energy for sintering increases with decreasing specific surface area and, in most cases, it does not change significantly in the approximately 70–85% range of relative density.     

Low-Temperature Sol-Gel Synthesis of Single-Phase ZrTiO4 Nanoparticles

Ceramic ZrTiO₄ powders were prepared by a sol-gel method using zirconium oxychloride and titanium tetraisopropoxide. In situ high temperature X-ray diffraction results show that crystallization of the amorphous gel starts at 400 ^∘C. Single-phase ZrTiO₄ nanoparticles were obtained after heat treatment at 450 ^∘C for one hour. An average particle size of 46 nm has been determined by nitrogen adsorption analysis. After pressing these sinteractive powders, pellets with controlled pore size distribution were obtained by sintering at temperatures as low as 400 ^∘C. The analysis of pores by mercury porosimetry gives an average porosity of 45%. The electrical resistivity, determined by impedance spectroscopy measurements at 24 ^∘C under different humidity environments, shows the ability of these pellets to adsorb water vapor in the porous surfaces. Pellets fabricated with the nanosized powders prepared by the sol-gel technique are proposed as good candidates to be used in humidity sensing devices.