A novel specimen for investigating the mechanical behavior of elastomers under multiaxial loading conditions

In this paper we describe the design and manufacture of an axial-torsion test specimen, and provide relationships needed when conducting stress-strain characterization experiments with the specimen. The specimen is a short hollow cylinder of rubber bonded between two steel mounting rings, in which simultaneous axial and shear strains are produced via independently controlled axial and twist displacements. We present calculations for the strain-displacement and stress-load relationships, and strain energy density. These relationships have been established and validated via a combination of analytical and experimental techniques, and finite element analysis. We have investigated the extent and effects of strain and stress field non-uniformity in the test specimen. The specimen design is sufficiently simple that a closed-form expression for the strain-displacement relationship has been successfully developed.     

Vanadium oxide monolayer catalysts. I. Preparation,characterization, and thermal stability

Vanadium oxide catalysts of the monolayer type have been prepared by means of chemisorption of vanadate(V)-anions from aqueous solutions and by chemisorption of gaseous V₂O₃(OH)₄. Using Al₂O₃, Cr₂O₃, TiO₂, CeO₂ and ZrO₂, catalysts with an approximately complete monomolecular layer of vanadium(V) oxide on the carrier oxides can be prepared, if temperature is not too high. Divalent metal oxides like CdO and ZnO may already form threedimensional surface vanadates at moderate temperature. The thermal stability of a monolayer catalyst is related to the parameter z/a, i. e. the ratio of the carrier cation charge to the sum of ionic radii of carrier cation and oxide anion. Thus, monolayer catalysts will be thermally stable only under the condition that z/a is not too high (aggregated catalyst) nor too small (ternary compound formation).     

Direct Synthesis of Anatase Films with ~100% (001) Facets and [001] Preferred Orientation

Anatase films exhibiting ~100% (001) reactive facets at the surface were grown hydrothermally on gold substrate from a homogeneous solution of TiF(4) and NaF. In addition to NaF, it was found that TiO(2) films with very similar properties could be prepared with the fluoride salts LiF, CsF, HF, NH(4)F, and N(CH(2)CH(3))(4)F. The polycrystalline anatase films are continuous, approximately 1 μm thick, and evenly coat the substrate. The surface grain size is ~400 nm. Grazing angle XRD measurements show that the films exhibit a high degree of preferred orientation with the c-axis normal to the substrate surface. SEM images reveal that the grains span the thickness of the films. Annealing the films at 500 °C removes fluorine and causes crystallites within the grains to restructure as shown by SEM, XRD, and Raman spectroscopy. Supported anatase films grown from this one-pot method may serve as oxidative photocatalysts and electrodes for photoelectrochemical applications such as solar cells and hydrogen evolution.     

Application of particle-induced X-ray emission, backscattering spectrometry and scanning electron microscopy in the evaluation of orthodontic materials

The focus of this investigation was on orthodontic materials used in the manufacture of dental brackets. The properties of these dental materials are subjected to various physical parameters such as elongation, yield strength and elasticity that justify their application. In turn, these parameters depend on the quantitative elemental concentration distribution (QECD) in the materials used in the manufacture. For compositional analysis, proton-induced X-ray emission (PIXE), backscatter spectrometry (BS) and scanning electron microscopy (SEM) were applied. QECD analysis was performed to correlate the physical parameters with the composition and to quantify imperfections in the materials. PIXE and BS analyses were performed simultaneously with a 3 MeV proton beam while electrons accelerated at 25 keV were used for the SEM analysis. From the QECDs it was observed that: (1) the major elements Cr, Fe and Ni were homogeneously distributed in the orthodontic plate; (2) the distribution of Mo and O correlated with one another; (3) there was a spread of Cr around regions of high C concentration; and, (4) areas of high concentrations of Mo and O corresponded to a decrease in C concentrations. Elemental concentration correlations are shown to indicate the similarities and differences in the ease of formation of phases, based on the tangent of linearity.     

Merrifield resin-supported chain transfer agents, precursors for RAFT polymerization

The modification of Merrifield resins to form chain transfer agent (CTA) precursors for reversible addition fragmentation chain transfer (RAFT) polymerization is investigated. A series of CTA precursor resins were prepared and characterized by FTIR and elemental analysis (EA). [reaction: see text]     

Ring‐Extended Gramicidin S Analogs Containing cis δ‐Sugar Amino Acid Turn Mimetics with Varying Ring Size

This article presents a series of ring‐extended gramicidin S derivatives, 9 – 14 , that have four ornithine residues as polar protonated side chains and one modified turn region containing a mono‐functionalized cis‐δ‐oxetane, δ‐furanoid, or δ‐pyranoid sugar amino acid residue. Of the GS analogs evaluated, we identified compound 7 , which contains the mono‐benzyloxy cis‐δ‐pyranoid sugar amino acid, as having a better biological profile than the clinically applied topical antibiotic gramicidin S.     

Phenol, chlorobenzene and chlorophenol isomers: resonant states and dissociative electron attachment

This paper reports a study of resonant dissociative electron attachment (DEA) to the phenol, chlorobenzene, p-, m-, and o-chlorophenol molecules. On the basis of spectroscopic and thermochemical approaches the resonant states of the molecular negative ions (NIs) and the structures of some dissociative decay products are assigned. In the electron energy range up to 3 eV, DEA processes are determined by the two 2[pi*]-shape resonances resulting mainly in formation of [M-H]- and/or Cl- ions. At higher electron energies the energy correlation between peaks in the negative ion effective yield curves and bands of UV spectra allowed identification of the core-excited resonances. The peculiarities of Cl- ion formation and the vibrational fine structure on the effective yield curves of the [M-H]- ions are discussed. The mass spectrometric procedures for measurement of relative cross sections for NI formation are described.