Cobalt promoted Ni/MgAl2O4 catalyst in lean methane catalytic oxidation

In the present research, magnesium aluminate spinel was prepared as catalyst support using a novel, facile, and efficient mechanochemical method. The Co-promoted catalysts with 20 wt.% of Ni were fabricated using an impregnation route and the samples were analyzed by the X-ray diffraction (XRD), N₂ adsorption/desorption (BET), temperature-programmed reduction and desorption (H₂-TPR and O₂-TPD), and field emission scanning electron microscopy (FESEM) tests. The results confirmed that all samples have a mesoporous structure with a high specific surface area and the presence of cobalt caused complete CH₄ oxidation at low temperatures, and no side reactions were observed. The results indicated that the 3%Co-20%Ni/MgAl₂O₄ catalyst was the optimal sample among the prepared catalysts, owing to the improvement of reduction features and oxygen mobility. The 50 and 90% of methane conversion was obtained at 530 and 600 °C, respectively. Also, the influence of calcination temperature, GHSV, and feed ratio was determined on the catalytic activity. The obtained outcomes revealed that the calcination temperature has a significant effect on the textural properties and catalytic efficiency. The sample calcined at 700 °C showed the weakest performance, which was related to the sintering of particles at high temperatures. The catalytic stability showed that the 3%Co-20%Ni/MgAl₂O₄ has acceptable stability during 600 min time of reaction.

Graphical abstract

     

Efficacy of incorporating PCMs into the commercial wall on the energy-saving annual thermal analysis

Journal of Thermal Analysis and Calorimetry - In this study, the efficacy of incorporating phase change material (PCM) into the building walls on the annual heat transfer reduction is examined....     

Fully developed mixed convection in horizontal and inclined tubes with uniform heat flux using nanofluid

Fully developed laminar mixed convection of a nanofluid consists of water and Al₂O₃ in horizontal and inclined tubes has been studied numerically. Three-dimensional elliptic governing equations have been solved to investigate the flow behaviors over a wide range of the Grashof and Reynolds numbers. Comparisons with previously published experimental and numerical works on mixed convection in a horizontal and inclined tube are performed and good agreements between the results are observed. Effects of nanoparticles concentration and tube inclinations on the hydrodynamics and thermal parameters are presented and discussed. It is shown that the nanoparticles concentration does not have significant effects on the hydrodynamics parameters. Heat transfer coefficient increases by 15% at 4 Vol.% Al₂O₃. Skin friction coefficient continually increases with the tube inclination, but the heat transfer coefficient reaches a maximum at the inclination angle of 45°.     

Numerical Modeling of Solitons in a Low Birefringent Optical Fiber

A numerical investigation, based on the split-step Fourier transform algorithm of all optical switching of solitons in a low birefringent optical fiber is presented. The numerical algorithm is described in detail. This revised version was published online in August 2006 with corrections to the Cover Date.     

Titanium(IV) tungstosilicate and titanium(IV) tungstophosphate: two new inorganic ion exchangers

Crystalline phases of Ti(IV) tungstosilicate and Ti(IV) tungstophosphate have been synthesised. The ion-exchange capacities of Ti(IV) tungstosilicate and Ti(IV) tungstophosphate have been reported as 0.44 and 0.80 mequiv./g, respectively. Both materials show monofunctional ion-exchange characteristic and are stable in 0.1 M solutions of HNO3, HCl, H2SO4 and acetone and benzene. Ti(IV) tungstosilicate is found to be more stable thermally than Ti(IV) tungstophosphate (loss in ion-exchange capacity was found as 58 and 80%, respectively for samples heated at 200 degrees C). The Kd values for heavy metals such as Pb, Hg, Cd, Sb, Co, Zn, Ni, Fe, Cr etc. have been reported in demineralised water and two surfactant media by batch processes. Cr3+, Fe3+ and Sn4+ are totally adsorbed on both the materials in demineralised water while a decrease in Kd value with increase in concentration of two surfactants is reported. On the basis of Kd values for metal ions, thirteen binary separations and five ternary separations on Ti(IV) tungstosilicate and thirteen different binary separations and four different ternary separations on Ti(IV) tungstophosphate have been achieved. Separation of methylamine from ethylamine has been done by GC on a column packed with Ti(IV) tungstophosphate.     

High temperature reactions of titanium(IV) oxide with some alkali persulfates and their decomposition products

The solid state reactions between TiO₂ and Na₂S₂O₈ or K₂S₂O₈ have been investigated using TG, DTG, DTA, IR, and X-ray diffraction studies in the range of 20 to 1000°C.It has been shown that TiO₂ reacts stoichiometrically (1 : 1) with Na₂S₂O₈ in the range of 160 and 220°C forming the complex sodium monoperoxodisulfato—titanium(IV) as characterized by IR and X-ray analysis. The new complex then decomposes into the reactants above 190°C.An exothermic reaction has been observed between TiO₂ and molten K₂S₂O₇ at mole ratio 1:2 respectively and higher, in the range of 280 and 350°C. The IR and X-ray analyses have shown the formation of a complex namely, potassium tetrasulfato titanium(IV) for which the formula and structure have been proposed. This complex decomposes at higher temperatures into K₂SO₄ and a mixed sulfate of potassium and titanium. The mixed sulfate melts at 620°C and decomposes into K₂SO₄, TiO₂, and the gaseous SO₃.On the other hand, Na₂S₂O₈ decomposes in a special mode producing a polymeric product of Na₁₀S₉O₃₂. Decomposition of this species occurs after melting at 560°C into Na₂SO₄ and sulfur oxides. The decomposition reaction has been proved to be catalysed by TiO₂ itself.