Synthesis and refractive‐index control of fluoropolymers by the polyaddition of bis(epoxide)s and triazine di(aryl ether)s

The polyaddition of fluorine‐containing bis(epoxide)s and fluorine‐containing triazine di(aryl ether)s were examined to give the corresponding fluorine‐containing poly(cyanurate)s. It was observed that the synthesized fluoropolymers had good thermal stabilities and good film‐forming properties. The glass transition temperatures (T_g's) and refractive‐indices (n_D's) of synthesized polymers were determined by differential scanning calorimetry and ellipsometry, respectively, and it was found that the values of T_g's and n_D's were supported by their fluorine containing ratios and skeletons. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4421–4429, 2007     

Improved detectability with a polymer-based trapping device in rapid HPLC analysis for ultra-low levels of bisphenol A (BPA) in environmental samples.

A new high-performance liquid chromatography (HPLC) method has been developed to detect ultra-low concentrations of bisphenol-A (BPA) (below 1 ng/L (ppt)) using column switching electrochemical detection (ECD). The results were superior to those obtained from manual pretreatment procedure with membrane stationary phase. BPA is inherently ubiquitous in the environment, including tools and solvents used for its analysis; to obtain meaningful results, therefore, the concentration of the overall BPA contamination must be below the detection limit for BPA using the analytical system. Therefore, purified water for preparing the standard BPA solution must be filtered with a hydrophobic membrane to suppress BPA background levels of contamination. In addition, we investigated methods for effectively preserving environmental water containing BPA. The addition of a small amount of ethylenediaminetetraacetic acid (EDTA) provided good recovery even after overnight storage. By employing these precautionary measures and procedures to reduce BPA contamination from the analytical procedure, we could accurately determine l(-10) ppt of BPA in environmental water samples using a column switching HPLC system.     

2‐connected 7‐coverings of 3‐connected graphs on surfaces

An m‐covering of a graph G is a spanning subgraph of G with maximum degree at most m. In this paper, we shall show that every 3‐connected graph on a surface with Euler genus k ≥ 2 with sufficiently large representativity has a 2‐connected 7‐covering with at most 6k ? 12 vertices of degree 7. We also construct, for every surface F² with Euler genus k ≥ 2, a 3‐connected graph G on F² with arbitrarily large representativity each of whose 2‐connected 7‐coverings contains at least 6k ? 12 vertices of degree 7. © 2003 Wiley Periodicals, Inc. J Graph Theory 43: 26–36, 2003     

Basic study of the gelation of dimethacrylate‐type crosslinking agents

An investigation was made of the gelation of dimethacrylate‐type crosslinking agents in view of an application for separation media. The study mainly centered on a crosslinking agent, glycerol dimethacrylate (GDMA), which is relatively hydrophilic because of a hydroxyl group in the middle of its structure. The gelation of GDMA was compared with that of other hydrophobic crosslinking agents such as ethylene glycol dimethacrylate and 1,6‐hexanediol dimethacrylate. The diluents used in the study were toluene, toluene with methanol, and cyclohexanol. The gelation was observed in real time with a charge coupled device camera and dynamic light scattering (DLS). Also, the separated dry gels were extensively characterized with scanning electron microscopy, BET (N₂ absorption and desorption isotherm), and Fourier transform infrared. DLS analysis showed a stronger molecular interaction of GDMA gelation in toluene, whereas this interaction was much weaker in an alcoholic solvent such as toluene with methanol or cyclohexanol. This indicated that GDMA gelation might proceed through hydrogen bonding as well as a crosslinking reaction of vinyl groups. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 949–958, 2006     

Chemically modified proton‐conducting membranes based on sulfonated polyimides: Improved water stability and fuel‐cell performance

A series of branched/crosslinked sulfonated polyimide (B/C‐SPI) membranes were prepared and evaluated as proton‐conducting ionomers based on the new concept of in situ crosslinking from sulfonated polyimide (SPI) oligomers and triamine monomers. Chemical branching and crosslinking in SPI oligomers with 1,3,5‐tris(4‐aminophenoxy)benzene as a crosslinker gave the polymer membranes very good water stability and mechanical properties under an accelerated aging treatment in water at 130 °C, despite their high ion‐exchange capacity (2.2–2.6 mequiv g^?1). The resulting polymer electrolytes displayed high proton conductivities of 0.2–0.3 S cm^?1 at 120 °C in water and reasonably high conductivities of 0.02–0.03 S cm^?1 at 50% relative humidity. In a single H₂/O₂ fuel‐cell system at 90 °C, they exhibited high fuel‐cell performances comparable to those of Nafion 112. The B/C‐SPI membranes also displayed good performances in a direct methanol fuel cell with methanol concentrations as high as 50 wt % that were superior to those of Nafion 112. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 3751–3762, 2006     

Simultaneous imaging of the structure and fluorescence of a supramolecular nanostructure formed by the coupling of π‐conjugated polymer chains in the intermolecular interaction

We fabricated a micrometer‐long supramolecular chain in which π‐conjugated polyrotaxane was coupled. A new experimental setup was designed and constructed, and the simultaneous direct imaging of the structure and fluorescent function was achieved. Furthermore, we identified the formation of a polymer intertwined network and observed novel fluorescence due to a long‐range interaction via this intertwined network over a distance of 5 μm or more without quenching over 15 min in the near field. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 801–809, 2006     

Antithrombogenicity of cultured endothelial cell-detached surface

To examine the antithrombogenicity of cultured endothelial cell-detached surface, a simple hybrid vascular model tube consisting of a glass tube and endothelial cells was constructed. To detach the endothelial cells from the inner surface of the model tube, a steady shear stress of 2 or 8 N m(-2) was imposed onto the surface of endothelial cell monolayer by means of a coaxial double cylinder rotational-type apparatus. Coagulation of blood in contact with the endothelial cell-detached surface was examined using a damped oscillation rheometer. Coagulation of whole blood in the cell-detached tube occurred at about 40 min, which was almost the same as that in the endothelial cell-coated tube. A few platelets without shape change adhered to the endothelial cell-detached surface. These data suggest that the endothelial cell-detached surface may exhibit antithrombogenic and anticoagulant surfaces. Biochemical analyses showed that the glass surface, where endothelial cell was detached, was covered with components such as collagen type IV that is considered to be produced from the endothelial cells on the glass surface.