Improvement in flow-sheet of extraction chromatography for trivalent minor actinides recovery

Journal of Radioanalytical and Nuclear Chemistry - Extraction chromatography flow-sheet employing octyl(phenyl)-N,N-diisobutylcarbonoylmethylphosphine oxide and bis(2-ethylhexyl) hydrogen phosphate...     

The required sample size in measuring oblique incidence absorption coefficient Experimental study

It is an important issue to clarify the minimum required size of a specimen for the accurate measurement of oblique incidence absorption coefficient. Investigation is made on the basis of experimental studies in a laboratory, using Aoshima's time stretched pulse technique. Measurements are carried out for glass fiber with thickness of 50 and 100 mm as highly absorbing materials and for ceramic with a thickness of 52 mm as relatively low absorbing material. The tested surface areas range from 0.0625 to 42 m² for glass fiber and from 0.1563 to 39.168 m² for ceramics. The absorption coefficients are determined at incidence angles from 0 to 45° in increments of 15°. With consideration of an active surface bounded by ellipse orbit, the minimum required surface area is 16 m² with a ratio of length to width of about 1.25. This value is twice the area size of the active surface, which is calculated from the geometry of source and microphone, and the width of the temporal window.     

Trinucleon cluster structure at high-excitation energies in A=6 nuclei

Trinucleon molecular structures in ⁶He and ⁶Be were investigated by using the ⁶Li(⁷Li, ⁷Be)⁶He reaction at 455 MeV and ⁶Li(³He, t)⁶Be reaction at 450 MeV, respectively. Binary decays into t + t from a broad state at E _x =18.0±1.0 MeV in ⁶He and into ³He + ³He from one at E _x =18.0±1.2 MeV in ⁶Be, respectively, were observed by measuring trinucleon cluster decays in coincidence with reaction particles. The branching ratios for binary decay were estimated to be about 0.7 for ⁶He and ⁶Be. These large branching ratios show that a trinucleon cluster state exists as an isobaric partner around E _x =18 MeV in ⁶He and ⁶Be.     

Development of Non-Halogen Flame Retardant Optical Fiber and Optical Fiber Cord

A non-halogen highly flame-retardant 0.9mm optical fiber and 2.0mm simplex optical cord, which are harmonized with the ecosystem, have been developed. The characteristics of them are presented in this paper.     

Anomalous PL brightening caused by partial Auger recombination of a (D, X) complex during an impact ionization avalanche in n-GaAs

Partial Auger recombination of the (D⁰, X) bound-exciton in n-GaAs at 4.2 K during an impact ionization avalanche under an applied pulse voltage has been investigated. The bright photoluminescence (PL)-pattern observed by applying the pulse voltage, characterizes well the formation of a current density filament. The observation of the bright PL spectra inside the current density filament gives a quite new result concerning the partial Auger recombination process of the (D⁰, X) complex, leaving the neutral donor in the excited states.     

High-quality hydroxyapatite coating on biocompatible materials by laser-assisted laser ablation method

A new method for high-quality hydroxyapatite (HAp) coating is developed, the laser-assisted laser ablation method. In this method, two lasers are used. One is used for ablation of a HAp target. The other, the assist laser, is used to irradiate a Ti substrate surface. The effects of the assist laser irradiation are to anneal the HAp coating and to improve its adhesive strength to the Ti substrate. The quality of the HAp coating depends on the delay time of the assist-laser irradiation. HAp coatings obtained at a delay time of 10 microseconds or more are more amorphous. It was confirmed that the amorphous part of a coating dissolves in simulated body fluid, while the crystalline part does not. The value of the Ca/P ratio in a coating obtained at a delay time of a few microseconds is close to the stoichiometric value. PACS 81.16.Mk     

Keratinized epithelial transport of beta-blocking agents. I. Relationship between physicochemical properties of drugs and the flux across rat skin and hamster cheek pouch.

The maximum fluxes (Jmax) of beta-blockers through keratinized membranes were determined in vitro and compared with their physiochemical parameters such as lipophilicity (log k'0) and melting point (mp). Rat abdominal skin and hamster cheek pouch mucosa were used as the model membranes. Propranolol, metoprolol, timolol, pindolol, nadolol and agenolol were used as beta-blockers with a variety of physicochemical characters. Linear relations of Jmax with either log k'0 or mp were observed both in intact rat skin and in intact hamster cheek pouch, suggesting that the lipophilicity and thermodynamic activity of a drug in the crystal state primarily affect the drug's permeation through these membranes. However, the slope, dJmax/d(log k'0), for cheek pouch mucosa was greater than that for rat skin, corresponding to the lack of appendigeal shunt pathways in cheek pouch. Penetration studies using the delipidized membranes and the isolated stratum corneum sheet of hamster cheek pouch mucosa clarified that the primary rate-limiting barrier function might exist in the lipid layer of the stratum corneum. Jmax values for the tape-stripped and delipidized skins correlated with both the solubilities of drugs in the vehicle and with the mp, suggesting the polar porous characteristics of both model membranes. However, a theoretical approach confirmed that the contribution of an intracellular or aqueous pore route in the intact membrane to the permeation of drugs with positive lipophilic indexes is negligible.     

WIDE RANGE DETECTOR USING PARABOLIC CYLINDRICAL MIRROR FOR THz APPLICATIONS

A new, wide-band, high-speed and high-sensitivity THz detector has been developed. The prototype detector consists of a parabolic cylindrical mirror, a long wire antenna and a Schottky barrier diode. Direct detection measurements have shown a stable sensitivity of 150 ± 50 V/W for 1–2 THz without any adjustments. The long wire antenna was fixed at the focus of parabolic cylindrical mirror then it has been realized less operation steps, easy coupling to the external THz signals and a dramatic enhancement in the practicality of this system. The optically polished mirror and frosted surface one showed comparable sensitivities, thus easy polishing and less cost mirror fabrication can be applied for this system. The radiation pattern showed a maximum radiation angle of approximately 23° with its dominant main lobe, which was attributed to the wire antenna character and confirmed good agreements with classical antenna theory.     

Ethylene polymerization by chromium complexes with phosphorous‐bridged bisphenoxy ligand

Chromium catalysts combined with phosphorous‐bridged bisphenoxy ligands were found to be highly active for ethylene polymerization. The most efficient catalyst precursor among them, generated by combining bis[3‐tert‐butyl‐5‐methyl‐2‐hydroxyphenyl](phenyl)phosphine hydrochloride ( 1a ) and CrCl₃(THF)₃, was characterized. X‐ray analysis of (3‐tert‐butyl‐5‐methyl‐2‐phenoxy)(3‐tert‐butyl‐5‐methyl‐ 2‐hydroxyphenyl)(phenyl)phosphine bis(tetrahydrofuran)chromium dichloride ( 6 ), obtained by the reaction of 1a and CrCl₃(THF)₃ in the presence of NaH, revealed a unique structure in which one phenol moiety of the bisphenol did not coordinate to the chromium center. Complex 6 showed higher activities than those observed in the in situ catalyst system. Polyethylene of various molecular weights was obtained with differing activators. The highest activity (113.5 kg mmol (cat)^?1 h^?1) was observed when TIBA/TB was used as a cocatalyst. A medium molecular weight polymer with narrow molecular weight distribution (M_w = 128,700, M_w/M_n = 1.8) was obtained using a 6 ‐TIBA/B(C₆F₅)₃ system. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 3668–3676, 2007     

Strain analysis of Si by FEM and energy-filtering CBED.

Lattice strains around a platelet oxygen precipitate in Si wafer is studied by energy filtering convergent-beam electron diffraction (CBED) and calculations based on the finite element method (FEM). Local lattice strains are measured from CBD patterns obtained with a probe size less than 2 nm in a specimen thicker than 450 nm. Strains measured are compressive along a direction normal to a plate of the precipitation and tensile along a direction parallel to the plate. Two-dimensional stress fields near the precipitate are obtained with FEM computer analyses by fitting the measured strains. It appears that shear stresses are concentrated at the end of the precipitate edge and the maximum shear stress at an interface between the precipitate and the Si-matrix is 1.9 GPa. It is demonstrated that a combination of the energy filtering CBED and FEM is very useful for the study of local strains near interfaces in semiconductor devices, in particular for the study of stress fields that are too steep for application of the conventional CBED technique.