Thermal,morphostructural and spectrometric characterization of an antibacterial kaolinite-based filter modified with silver for water treatment

Journal of Thermal Analysis and Calorimetry - The aim of this work is to synthesize and characterize a new structured silver–clay dried, calcined or sintered at different temperatures...     

Application of pressure sensitive paint measurement to a low-solidity cascade diffuser of a transonic centrifugal compressor

A pressure sensitive paint (PSP) measurement has been known as a pressure field measurement technique based on the oxygen quenching phenomenon of luminescence of specific luminophores. A PSP measurement was applied for pressure field measurement in a low-solidity circular cascade diffuser of a single-stage transonic centrifugal compressor with 5 in pressure ratio for HFC134a gas. The oxygen concentration was about 500 ppm. Ru (bath-phen) was adsorbed on a silica-gel thinlayer chromatography sheet, and the sheet was pasted onto the side-wall between the cascade vanes. A drastic change in luminescent intensity was recognized during a surge condition. Also the pressure variations based on luminescent intensity agreed well with the pressure fluctuations measured using a semiconductor pressure sensor with high-frequency-response. It was shown that a PSP measurement worked well to investigate the unsteady pressure fields in a circular cascade diffuser of a transonic centrifugal compressor. Moreover, the time response of PSP becomes clear as a problem to be overcome for the present.     

Phase transitions of lanthanide monophosphides with NaCl-type structure at high pressures

Lanthanide monophosphides LnP (Ln = La, Ce, Pr, Nd, Sm, Gd, Tb, Tm and Yb) with a NaCl-type structure have systematically been prepared at high temperatures. Using synchrotron radiation, X-ray diffractions of LnP have been studied up to 61 GPa at room temperature. The NaCl---CsCl transition for CeP is found at around 25 GPa. First-order phase transitions of LnP (Ln = La, Pr and Nd) with the crystallographic change occur at around 24, 26 and 30 GPa, respectively. The structure of the high pressure phases of these phosphides is a body center tetragonal structure (Ln: 0, 0, 0; P: 1/2, 1/2, 1/2; space group P4/mmm), which can be seen as the distorted CsCl-type structure. The Pr---P distance in the high pressure form of PrP is 2.789 Å. This almost agrees with the sum of covalent radii of Pr and P. The Pr---P bond has the covalent character at very high pressures. Similar results are also obtained for LaP and NdP. The pressure-induced phase transitions of SmP, GdP, TbP, TmP and YbP occur at around 35, 40, 38, 53 and 51 GPa, respectively. The structure of the high pressure phase is unknown. The phase transitions of LnP with many f-electrons are not due to the mechanism of the ordinary NaCl---CsCl transition. The transition pressures of LnP increase with decreasing the lattice constants in the NaCl-type structure, which decrease with increasing atomic number of the lanthanide atoms.     

Synthesis of silicon nitride based ceramic nanoparticles by the pyrolysis of silazane block copolymer micelles

Diblock copolymer poly(1,1,3,N,N′‐pentamethyl‐3‐vinylcyclodisilazane)‐block‐polystyrene (polyVSA‐b‐polySt) and triblock copolymer poly(1,1,3,N,N′‐pentamethyl‐3‐vinylcyclodisilazane)‐block‐polystyrene‐block‐poly(1,1,3,N,N′‐pentamethyl‐3‐vinylcyclodisilazane) (polyVSA‐b‐polySt‐b‐polyVSA), consisting of silazane and nonsilazane segments, were prepared by the living anionic polymerization of 1,1,3,N,N′‐pentamethyl‐3‐vinylcyclodisilazane and styrene. PolyVSA‐b‐polySt formed micelles having a poly(1,1,3,N,N′‐pentamethyl‐3‐vinylcyclodisilazane) (polyVSA) core in N,N‐dimethylformamide, whereas polyVSA‐b‐polySt and polyVSA‐b‐polySt‐b‐polyVSA formed micelles having a polyVSA shell in n‐heptane. The micelles with a polyVSA core were core‐crosslinked by UV irradiation in the presence of diethoxyacetophenone as a photosensitizer, and the micelles with a polyVSA shell were shell‐crosslinked by UV irradiation in the presence of diethoxyacetophenone and 1,6‐hexanedithiol. These crosslinked micelles were pyrolyzed at 600 °C in N₂ to give spherical ceramic particles. The pyrolysis process was examined by thermogravimetry and thermogravimetry/mass spectrometry. The morphologies of the particles were analyzed by atomic force microscopy and transmission electron microscopy. The chemical composition of the pyrolysis products was analyzed by X‐ray fluorescence spectroscopy and Raman scattering spectroscopy. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 4696–4707, 2006     

Acylation of hydrazides with acetic acid and formic acid

In peptide synthesis, hydrazides are important intermediates for the azide coupling method. A hydrazide is converted to the corresponding azide in the presence of an acid and a nitrite. When acetic acid (or formic acid) is used as the acid, partial acetylation (or formylation) of the hydrazide occurs as a side reaction. Formylation of the hydrazide is much faster than acetylation. Removal of the formyl group on the hydrazide with hydrazine and hydroxylamine was studied. The rate of deformylation with hydrazine treatment is faster than that with hydroxylamine treatment.     

Polyiodide composition in poly(vinyl acetate)-iodine-iodide complex

Polyiodide formed by complexation of poly(vinyl acetate) (PVAc) with iodine in the presence of iodide has been investigated by chemical analysis and resonance Raman spectrophotometry. When PVAc films were immersed in iodide-iodine aqueous solutions which had different ratios of iodide to iodine concentration [I^?]/[I₂], the complex films exhibited tremendous variations of swelling degree, despite the relatively small change in the amount of bound iodine. From a quantitative chemical analysis, the composition of polyiodide bound to PVAc was found to be 1.01 ± 0.035 in the molar ratio of iodide to iodine irrespective of the composition of the iodide-iodine aqueous solution ([I^?]/[I₂] = 2–500). The polyiodide formed in PVAc-iodine-iodide complex was therefore inferred to be (I₃^?)_n. Resonance Raman spectra obtained on PVAc-iodine-iodide complexes were also identical to those of the benzamide-iodine complex, in which the polyiodide consists of (I₃^?)_n, consistent with the result from chemical analysis.     

Fully automated micro- and nanoscale one- or two-dimensional high-performance liquid chromatography system for liquid chromatography-mass spectrometry compatible with non-volatile salts for ion exchange chromatography

A one- or two-dimensional high performance liquid chromatography system for electrospray ionization mass spectrometers has been developed that is optimized for ion exchange and reversed phase separations. A unique and simple valve configuration permits the use of a variety of non-volatile salts; ammonium sulfate was used in an example of strong cation exchange separations. The system was designed and evaluated for both micro- and nanoflow chromatography. The peptide detection limit was approximately 100 fmol for micro- and 20 fmol for nanoflow, demonstrating the concentration and mass sensitivity improvements expected with nanoelectrospray ionization. The 1D/2D-HPLC MS system is fully automated for routine peptide analyses, compatible with direct injection of proteolytic digests, and exhibits chromatographic reproducibility and sensitivity. Software permits operator selection of either a 1D or 2D configuration with corresponding system parameters as required for individual samples. The hardware elements and resulting performance are described in this paper.     

Fluorimetric assay for measuring Dns-His-Lys-Arg-His-Lys cleaving enzyme using high-performance liquid chromatography

A rapid and sensitive assay for the determination of Dns-His-Lys-Arg-His-Lys cleaving enzyme activity is reported. This assay is based on fluorimetric detection of a dansylated dipeptide, 5-dimethylaminonaphthalene-1-sulfonyl-His-Lys, enzymatically formed from the substrate 5-dimethylaminonaphthalene-1-sulfonyl-His-Lys-Arg-His-d-Lys, after separation by high-performance liquid chromatography (HPLC) using a C-18 reversed-phase column by isocratic elution. This assay is sensitive enough to measure 5-dimethylaminonaphthalene-1-sulfonyl-His-Lys at concentrations as low as 7 pmol, and yields highly reproducible results and requires less than 9.0 min per sample for separation and quantitation. The optimum pH for Dns-His-Lys-Arg-His-Lys cleaving enzyme activity was 7.5-8.0. The Michaelis constant (K_m) and the maximum velocity (V_max) values were 33.3 μM and 47.07 pmol/(μg h), respectively with the use of enzyme extract obtained from bovine pituitary. By using this assay, axonal transport of this enzyme activity was observed 48 h after double ligations of rat sciatic nerves. The high sensitivity and selectivity of this assay would be useful for clarification of the physiological role of this enzyme.     

Recent progress of high-power negative ion beam development for fusion plasma heating

A negative-ion-based neutral beam injector (N-NBI) has been constructed for JT-60U. The N-NBI is designed to inject 500 keV, 10 MW neutral beams using two ion sources, each producing a 500 keV, 22 A D⁻ ion beam. In the preliminary experiment using one ion source, a D⁻ ion beam of 13.5 A has been successfully accelerated with an energy of 400 keV (5.4 MW) for 0.12 s at an operating pressure of 0.22 Pa. This is the highest D⁻ beam current and power in the world. Co-extracted electron current was effectively suppressed to the ratio of Ie/I_D⁻ < 1. The highest energy beam of 460 keV, 2.4 A, 0.44 s has also been obtained. To realize 1 MeV class NBI system for ITER (International Thermonuclear Experimental Reactor), demonstration of ampere class negative ion beam acceleration up to 1 MeV is an important mile stone. To achieve the mile stone, a prototype accelerator and a 1 MV, 1 A test facility called MeV Test Facility (MTF) were constructed. Up to now, an H⁻ ion beam was accelerated up to the energy of 805 keV with an acceleration drain current of 150 mA for 1 s in a five stage electrostatic multi-aperture accelerator.     

Selective chemical vapor deposition synthesis of double-wall carbon nanotubes on mesoporous silica

Double-wall carbon nanotubes (DWNTs) have been selectively synthesized over Fe/Co loaded mesoporous silica by catalytic chemical vapor deposition of alcohol. Several silica materials with desired pore diameter and morphology have been investigated for the DWNT growth. The diameter distribution and selectivity of the DWNT are found to depend on the reaction temperature, pore size, and thermal stability of the support material. A high-yield synthesis of DWNTs has been achieved at 900 degrees C over high-temperature stable mesoporous silica. The outer diameter of DWNTs is found to be in the range of 1.5-5.4 nm with a "d" spacing of 0.38 +/- 0.02 nm between inner and outer layers, which is much larger than those of multiwall carbon nanotubes.