Determination of trace levels of titanium in polyolefin polymers by catalytic reduction using square wave voltammetry

A sensitive and rapid method for the determination of trace levels of titanium in polyolefin polymers using square wave voltammetry is discussed. It involves ashing, acid digestion of polymer samples and determination of titanium(IV) by catalytic reduction using square wave voltammetric (SWV) technique. A well defined peak of titanium(IV) in Britton-Robinson buffer solution containing EDTA and KBrO(3) is observed in the potential range of -0.10 to -0.40 vs. Ag/AgCl. Calibration graphs were linear in the range 0.05-0.25 microg/ml for titanium. Effects of pH and concentration of bromate, EDTA and buffer constituents are studied for the optimization of experimental conditions. Interference from other concomitants present in the polymer matrix are studied. Low density polyethylene (LDPE) obtained by tubular process was used for preparing the synthetic standards in order to optimize the experimental conditions and good recoveries (99-101%) were obtained. The method was extended to different polyolefin samples and the results obtained for the titanium content compared with those obtained by UV/Vis spectrophotometry. Statistical evaluation showed no significant bias between the two methods. SWV is found suitable for the estimation of Ti in the range 1-50 microg/g in polyolefin polymers with a RSD < 2.0%.     

Engineering a Small HOMO–LUMO Gap and Intramolecular C−H Borylation by Diborene/Anthracene Orbital Intercalation

The diborene 1 was synthesized by reduction of a mixture of 1,2-di-9-anthryl-1,2-dibromodiborane(4) ( 6 ) and trimethylphosphine with potassium graphite. The X-ray structure of 1 shows the two anthryl rings to be parallel and their π(C₁₄) systems perpendicular to the diborene π(B=B) system. This twisted conformation allows for intercalation of the relatively high-lying π(B=B) orbital and the low-lying π* orbital of the anthryl moiety with no significant conjugation, resulting in a small HOMO–LUMO gap (HLG) and ultimately a C−H borylation of the anthryl unit. The HLG of 1 was estimated to be 1.57 eV from the onset of the long wavelength band in its UV/Vis absorption spectrum (THF, λ_onset=788 nm). The oxidation of 1 with elemental selenium afforded diboraselenirane 8 in quantitative yield. By oxidative abstraction of one phosphine ligand by another equivalent of elemental selenium, the B−B and C¹−H bonds of 8 were cleaved to give the cyclic 1,9-diborylanthracene 9 .     

Understanding the Origin of Highly Selective CO2 Electroreduction to CO on Ni,N-doped Carbon Catalysts

Ni,N-doped carbon catalysts have shown promising catalytic performance for CO₂ electroreduction (CO₂R) to CO; this activity has often been attributed to the presence of nitrogen-coordinated, single Ni atom active sites. However, experimentally confirming Ni−N bonding and correlating CO₂ reduction (CO₂R) activity to these species has remained a fundamental challenge. We synthesized polyacrylonitrile-derived Ni,N-doped carbon electrocatalysts (Ni-PACN) with a range of pyrolysis temperatures and Ni loadings and correlated their electrochemical activity with extensive physiochemical characterization to rigorously address the origin of activity in these materials. We found that the CO₂R to CO partial current density increased with increased Ni content before plateauing at 2 wt % which suggests a dispersed Ni active site. These dispersed active sites were investigated by hard and soft X-ray spectroscopy, which revealed that pyrrolic nitrogen ligands selectively bind Ni atoms in a distorted square-planar geometry that strongly resembles the active sites of molecular metal–porphyrin catalysts.     

1,3‐Dehydro‐o‐Carborane: Generation and Reaction with Arenes

Like the importance of benzyne, witnessed in modern arene chemistry for decades, 1,2‐dehydro‐o‐carborane (o‐carboryne), a three‐dimensional relative of benzyne, has been used as a synthon for generating a wide range of cage, carbon‐functionalized carboranes over the past 20 years. However, the selective B functionalization of the cage still represents a challenging task. Disclosed herein is the first example of 1,3‐dehydro‐o‐carborane featuring a cage C? B bond having multiple bonding characters, and is successfully generated by treatment of 3‐diazonium‐o‐carborane tetrafluoroborate with non‐nucleophilic bases. This presents a new methodology for simultaneous functionalization of both cage carbon and boron vertices.     

Regioselective Insertion of o‐Carborynes into the α‐CH Bond of Tertiary Amines: Synthesis of α‐Carboranylated Amines

o‐Carboryne can undergo α‐C? H bond insertion with tertiary amines, thus affording α‐carboranylated amines in very good regioselectivity and isolated yields. In this process, the nucleophilic addition of tertiary amines to the multiple bond of o‐carboryne generates a zwitterionic intermediate. An intramolecular proton transfer, followed by a nucleophilic attack leads to the formation of the final product. Thus, regioselectivity is highly dependent upon the acidity of α‐C? H proton of tertiary amines. This approach serves as an efficient methodology for the preparation of a series of 1‐aminoalkyl‐o‐carboranes.     

Understanding the Origin of Highly Selective CO2 Electroreduction to CO on Ni,N‐doped Carbon Catalysts

Ni,N‐doped carbon catalysts have shown promising catalytic performance for CO₂ electroreduction (CO₂R) to CO; this activity has often been attributed to the presence of nitrogen‐coordinated, single Ni atom active sites. However, experimentally confirming Ni?N bonding and correlating CO₂ reduction (CO₂R) activity to these species has remained a fundamental challenge. We synthesized polyacrylonitrile‐derived Ni,N‐doped carbon electrocatalysts (Ni‐PACN) with a range of pyrolysis temperatures and Ni loadings and correlated their electrochemical activity with extensive physiochemical characterization to rigorously address the origin of activity in these materials. We found that the CO₂R to CO partial current density increased with increased Ni content before plateauing at 2 wt % which suggests a dispersed Ni active site. These dispersed active sites were investigated by hard and soft X‐ray spectroscopy, which revealed that pyrrolic nitrogen ligands selectively bind Ni atoms in a distorted square‐planar geometry that strongly resembles the active sites of molecular metal–porphyrin catalysts.     

Residual Dipolar-Coupling-Based Conformational Comparison of Noncovalent Ubiquitin Homodimer with Covalently Linked Diubiquitin

Although the conformation of the polymer chain of Ubiquitin (Ub) mainly depends on the type of isopeptide linkage connecting two Ub molecules, the non-covalent (noncovalent) interaction between two Ub molecules within the chain could also tune their conformational preference. Here, we studied the conformation of noncovalently formed Ub dimers in solution using residual dipolar couplings (RDCs). Comparing the RDC derived alignment tensor of the noncovalently formed dimer with the two most abundant (K11 and K48) covalent linked Ub dimers revealed that the conformation of K11 linked and noncovalent Ub dimers were similar. Between the various NMR and crystal structures of K11 linked Ub dimers, RDC tensor analysis showed that the structure of K11 linked dimer crystalized at neutral pH is similar to noncovalent dimer. Analogous to the experimental study, the comparison of predicted order matrix of various covalent Ub dimers with that of the experimentally determined order matrix of noncovalent Ub dimer also suggests that the conformation of K11 linked dimers crystalized at neutral pH is similar to the noncovalent dimer.     

Two-dimensional solidification of viscous flow over a semi infinite plate with constant heat removal

Two-dimensional solidification of forced viscous flow over a semi infinite flat plate is considered. The plate is initially maintained at a constant temperature above the freezing point of the liquid. At time t>0, heat is removed from the plate so that the liquid freezes. The continuity equation and the two-dimensional, nonsteady, momentum and energy equations in the liquid and solid phases are solved numerically. The growth of the solid layer as a function of time and position along the plate is determined.     

Characterization, sintering and dielectric properties of nanocrystalline zinc oxide prepared by a citric acid-based combustion route

Nanosized zinc oxide has been synthesized through a novel single step solution combustion route using citric acid as fuel. The X-ray diffraction (XRD) analysis revealed that the synthesized ZnO nanopowder has the pure wurtzite structure. The phase purity of the nanopowder has been confirmed using differential thermal analysis (DTA), thermogravimetric analysis (TGA) and Fourier transform infrared spectroscopy (FT-IR). The morphology and crystalline size of the as-prepared nanopowder characterized by scanning electron microscopy (SEM) and transmission electron microscopy (TEM) revealed that the powder consisted of a mixture of nanoparticles and nanorods. The nanocrystalline ZnO could be sintered to ∼97% of the theoretical density at 1200 °C in 4 h. The dielectric constant (ε_r) and dielectric loss (ε_i) of sintered ZnO pellets at 5 MHz were 1.38 and 9×10⁻², respectively, at room temperature.     

Effect of ZnO doping on the structural and optical properties of BaWO<Subscript>4</Subscript> thin films prepared using pulsed laser ablation technique

BaWO₄ doped with ZnO (2, 3, 5, 7 and 10 wt%) nanostructured films are prepared on quartz substrates by pulsed laser ablation. The films are post annealed at 900°C. GIXRD analysis of the post-annealed films reveal the change of orientation of scheelite tetragonal crystal growth from 1 1 2 reflection plane to 0 0 4 planes when doping concentration is more than 3 wt%. The AFM images show that film with 7 wt% ZnO doping concentration has good ceramic pattern with surface features giving a minimum value of rms surface roughness suitable for optoelectronic device applications. The optical transmittance and band-gap energy of the films are found to decrease considerably on postannealing which can be due to the increase in grain size of the crystallites on annealing. Thus doping with ZnO improves the surface features of the films and increases the optical band-gap energy.